Filtered by vendor Juniper
Subscriptions
Total
866 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2022-22203 | 1 Juniper | 11 Ex4600, Ex4650, Junos and 8 more | 2024-09-16 | 6.5 Medium |
| An Incorrect Comparison vulnerability in PFE of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a Denial of Service (DoS). On QFX5000 Series, and EX4600 and EX4650 platforms, the fxpc process will crash followed by the FPC reboot upon receipt of a specific hostbound packet. Continued receipt of these specific packets will create a sustained Denial of Service (DoS) condition. This issue only affects Juniper Networks Junos OS 19.4 version 19.4R3-S4. | ||||
| CVE-2021-0290 | 1 Juniper | 26 Ex9200, Ex9204, Ex9208 and 23 more | 2024-09-16 | 6.5 Medium |
| Improper Handling of Exceptional Conditions in Ethernet interface frame processing of Juniper Networks Junos OS allows an attacker to send specially crafted frames over the local Ethernet segment, causing the interface to go into a down state, resulting in a Denial of Service (DoS) condition. The interface does not recover on its own and the FPC must be reset manually. Continued receipt and processing of these frames will create a sustained Denial of Service (DoS) condition. This issue is platform-specific and affects the following platforms and line cards: * MPC7E/8E/9E and MPC10E on MX240, MX480, MX960, MX2008, MX2010, and MX2020 * MX204, MX10003, MX10008, MX10016 * EX9200, EX9251 * SRX4600 No other products or platforms are affected by this vulnerability. An indication of this issue occurring can be seen in the system log messages, as shown below: user@host> show log messages | match "Failed to complete DFE tuning" fpc4 smic_phy_dfe_tuning_state: et-4/1/6 - Failed to complete DFE tuning (count 3) and interface will be in a permanently down state: user@host> show interfaces et-4/1/6 terse Interface Admin Link Proto Local Remote et-4/1/6 up down et-4/1/6.0 up down aenet --> ae101.0 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S7 on MX Series; 17.1R1 and later versions prior to 17.2R3-S3 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S11, 17.4R3-S1 on MX Series, SRX4600; 18.1 versions prior to 18.1R3-S10 on MX Series, EX9200 Series, SRX4600; 18.2 versions prior to 18.2R3-S3 on MX Series, EX9200 Series, SRX4600; 18.3 versions prior to 18.3R3-S1 on MX Series, EX9200 Series, SRX4600; 18.4 versions prior to 18.4R2-S3, 18.4R3 on MX Series, EX9200 Series, SRX4600; 19.1 versions prior to 19.1R2-S1, 19.1R3 on MX Series, EX9200 Series, SRX4600; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series, EX9200 Series, SRX4600; 19.3 versions prior to 19.3R2 on MX Series, EX9200 Series, SRX4600. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1. | ||||
| CVE-2022-22173 | 1 Juniper | 1 Junos | 2024-09-16 | 7.5 High |
| A Missing Release of Memory after Effective Lifetime vulnerability in the Public Key Infrastructure daemon (pkid) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause Denial of Service (DoS). In a scenario where Public Key Infrastructure (PKI) is used in combination with Certificate Revocation List (CRL), if the CRL fails to download the memory allocated to store the CRL is not released. Repeated occurrences will eventually consume all available memory and lead to an inoperable state of the affected system causing a DoS. This issue affects Juniper Networks Junos OS: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue can be observed by monitoring the memory utilization of the pkid process via: root@jtac-srx1500-r2003> show system processes extensive | match pki 20931 root 20 0 733M 14352K select 0:00 0.00% pkid which increases over time: root@jtac-srx1500-r2003> show system processes extensive | match pki 22587 root 20 0 901M 181M select 0:03 0.00% pkid | ||||
| CVE-2019-0019 | 1 Juniper | 1 Junos | 2024-09-16 | 7.5 High |
| When BGP tracing is enabled an incoming BGP message may cause the Junos OS routing protocol daemon (rpd) process to crash and restart. While rpd restarts after a crash, repeated crashes can result in an extended DoS condition. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S4, 16.1R7-S5; 16.2 versions prior to 16.2R2-S9, 16.2R3; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3-S1; 17.3 versions prior to 17.3R3-S3, 17.3R3-S4, 17.3R4; 17.4 versions prior to 17.4R1-S7, 17.4R2-S3, 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S4, 18.1R4; 18.2 versions prior to 18.2R2-S2, 18.2R2-S3, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S3, 18.3R2; 18.4 versions prior to 18.4R1-S2, 18.4R2. This issue does not affect Junos releases prior to 16.1R1. | ||||
| CVE-2021-0211 | 1 Juniper | 87 Ex2200, Ex2200-c, Ex2200-vc and 84 more | 2024-09-16 | 10 Critical |
| An improper check for unusual or exceptional conditions in Juniper Networks Junos OS and Junos OS Evolved Routing Protocol Daemon (RPD) service allows an attacker to send a valid BGP FlowSpec message thereby causing an unexpected change in the route advertisements within the BGP FlowSpec domain leading to disruptions in network traffic causing a Denial of Service (DoS) condition. Continued receipt of these update messages will cause a sustained Denial of Service condition. This issue affects Juniper Networks: Junos OS: All versions prior to 17.3R3-S10 with the exceptions of 15.1X49-D240 on SRX Series and 15.1R7-S8 on EX Series; 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R2-S12, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S3; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R1-S3, 19.4R2-S3, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S3 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2. Junos OS Evolved: All versions prior to 20.3R1-S1-EVO, 20.3R2-EVO. | ||||
| CVE-2017-2339 | 1 Juniper | 1 Screenos | 2024-09-16 | N/A |
| A persistent cross site scripting vulnerability in NetScreen WebUI of Juniper Networks Juniper NetScreen Firewall+VPN running ScreenOS allows a user with the 'security' role to inject HTML/JavaScript content into the management session of other users including the administrator. This enables the lower-privileged user to effectively execute commands with the permissions of an administrator. This issue affects Juniper Networks ScreenOS 6.3.0 releases prior to 6.3.0r24 on SSG Series. No other Juniper Networks products or platforms are affected by this issue. | ||||
| CVE-2022-22233 | 1 Juniper | 2 Junos, Junos Os Evolved | 2024-09-16 | 5.5 Medium |
| An Unchecked Return Value to NULL Pointer Dereference vulnerability in Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a locally authenticated attacker with low privileges to cause a Denial of Service (DoS). In Segment Routing (SR) to Label Distribution Protocol (LDP) interworking scenario, configured with Segment Routing Mapping Server (SRMS) at any node, when an Area Border Router (ABR) leaks the SRMS entries having "S" flag set from IS-IS Level 2 to Level 1, an rpd core might be observed when a specific low privileged CLI command is issued. This issue affects: Juniper Networks Junos OS 21.4 versions prior to 21.4R1-S2, 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2. Juniper Networks Junos OS Evolved 21.4-EVO versions prior to 21.4R1-S2-EVO, 21.4R2-S1-EVO, 21.4R3-EVO; 22.1-EVO versions prior to 22.1R2-EVO. This issue does not affect: Juniper Networks Junos OS versions prior to 21.4R1. Juniper Networks Junos OS Evolved versions prior to 21.4R1-EVO. | ||||
| CVE-2019-0046 | 1 Juniper | 1 Junos | 2024-09-16 | 6.5 Medium |
| A vulnerability in the pfe-chassisd Chassis Manager (CMLC) daemon of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the EX4300 when specific valid broadcast packets create a broadcast storm condition when received on the me0 interface of the EX4300 Series device. A reboot of the device is required to restore service. Continued receipt of these valid broadcast packets will create a sustained Denial of Service (DoS) against the device. Affected releases are Juniper Networks Junos OS: 16.1 versions above and including 16.1R1 prior to 16.1R7-S5; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S2; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2. | ||||
| CVE-2021-31365 | 1 Juniper | 5 Ex2300, Ex3400, Ex4300 and 2 more | 2024-09-16 | 6.5 Medium |
| An Uncontrolled Resource Consumption vulnerability in Juniper Networks Junos OS on EX2300, EX3400 and EX4300 Series platforms allows an adjacent attacker sending a stream of layer 2 frames will trigger an Aggregated Ethernet (AE) interface to go down and thereby causing a Denial of Service (DoS). By continuously sending a stream of specific layer 2 frames an attacker will sustain the Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS EX4300 Series All versions prior to 15.1R7-S7; 16.1 versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS EX3400 and EX4300-MP Series All versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S9, 18.4R3-S7; 19.1 versions prior to 19.1R2-S3, 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2. Juniper Networks Junos OS EX2300 Series All versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R2. | ||||
| CVE-2018-0052 | 1 Juniper | 8 Ex2300, Ex3400, Junos and 5 more | 2024-09-16 | N/A |
| If RSH service is enabled on Junos OS and if the PAM authentication is disabled, a remote unauthenticated attacker can obtain root access to the device. RSH service is disabled by default on Junos. There is no documented CLI command to enable this service. However, an undocumented CLI command allows a privileged Junos user to enable RSH service and disable PAM, and hence expose the system to unauthenticated root access. When RSH is enabled, the device is listing to RSH connections on port 514. This issue is not exploitable on platforms where Junos release is based on FreeBSD 10+. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on QFX/EX Series; 15.1 versions prior to 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D131, 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 16.1 versions prior to 16.1R3-S9, 16.1R4-S9, 16.1R5-S4, 16.1R6-S4, 16.1R7; 16.2 versions prior to 16.2R2-S5; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.2X75 versions prior to 17.2X75-D110, 17.2X75-D91; 17.3 versions prior to 17.3R1-S4, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.2X75 versions prior to 18.2X75-D5. | ||||
| CVE-2017-2346 | 1 Juniper | 2 Junos, Mx | 2024-09-16 | N/A |
| An MS-MPC or MS-MIC Service PIC may crash when large fragmented packets are passed through an Application Layer Gateway (ALG). Repeated crashes of the Service PC can result in an extended denial of service condition. The issue can be seen only if NAT or stateful-firewall rules are configured with ALGs enabled. This issue was caused by the code change for PR 1182910 in Junos OS 14.1X55-D30, 14.1X55-D35, 14.2R7, 15.1R5, and 16.1R2. No other versions of Junos OS and no other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS on MX platforms running: 14.1X55 from 14.1X55-D30 to releases prior to 14.1X55-D35; 14.2R from 14.2R7 to releases prior to 14.2R7-S4, 14.2R8; 15.1R from 15.1R5 to releases prior to 15.1R5-S2, 15.1R6; 16.1R from 16.1R2 to releases prior to 16.1R3-S2, 16.1R4. | ||||
| CVE-2019-0060 | 1 Juniper | 25 Csrx, Junos, Srx100 and 22 more | 2024-09-16 | 7.5 High |
| The flowd process, responsible for forwarding traffic in SRX Series services gateways, may crash and restart when processing specific transit IP packets through an IPSec tunnel. Continued processing of these packets may result in an extended Denial of Service (DoS) condition. This issue only occurs when IPSec tunnels are configured. Systems without IPSec tunnel configurations are not vulnerable to this issue. This issue affects Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D171, 15.1X49-D180 on SRX Series; 18.2 versions 18.2R2-S1 and later, prior to 18.2R3 on SRX Series; 18.4 versions prior to 18.4R2 on SRX Series. | ||||
| CVE-2019-0036 | 1 Juniper | 1 Junos | 2024-09-16 | 9.8 Critical |
| When configuring a stateless firewall filter in Junos OS, terms named using the format "internal-n" (e.g. "internal-1", "internal-2", etc.) are silently ignored. No warning is issued during configuration, and the config is committed without error, but the filter criteria will match all packets leading to unexpected results. Affected releases are Juniper Networks Junos OS: All versions prior to and including 12.3; 14.1X53 versions prior to 14.1X53-D130, 14.1X53-D49; 15.1 versions prior to 15.1F6-S12, 15.1R7-S4; 15.1X49 versions prior to 15.1X49-D161, 15.1X49-D170; 15.1X53 versions prior to 15.1X53-D236, 15.1X53-D496, 15.1X53-D69; 16.1 versions prior to 16.1R7-S4, 16.1R7-S5; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R1-S8, 17.2R3-S1; 17.3 versions prior to 17.3R3-S4; 17.4 versions prior to 17.4R1-S7, 17.4R2-S3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S4; 18.2 versions prior to 18.2R1-S5, 18.2R2-S1; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S3; 18.4 versions prior to 18.4R1-S1, 18.4R1-S2. | ||||
| CVE-2020-1607 | 1 Juniper | 44 Ex2300, Ex2300-c, Ex3400 and 41 more | 2024-09-16 | 7.5 High |
| Insufficient Cross-Site Scripting (XSS) protection in J-Web may potentially allow a remote attacker to inject web script or HTML, hijack the target user's J-Web session and perform administrative actions on the Junos device as the targeted user. This issue affects Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D86, 12.3X48-D90 on SRX Series; 14.1X53 versions prior to 14.1X53-D51 on EX and QFX Series; 15.1F6 versions prior to 15.1F6-S13; 15.1 versions prior to 15.1R7-S5; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400 Series; 16.1 versions prior to 16.1R4-S13, 16.1R7-S5; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S2; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R2-S6, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.3 versions prior to 18.3R1-S6, 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S2, 19.1R2. | ||||
| CVE-2019-0021 | 1 Juniper | 3 Advanced Threat Prevention, Atp400, Atp700 | 2024-09-16 | N/A |
| On Juniper ATP, secret passphrase CLI inputs, such as "set mcm", are logged to /var/log/syslog in clear text, allowing authenticated local user to be able to view these secret information. This issue affects Juniper ATP 5.0 versions prior to 5.0.4. | ||||
| CVE-2016-4925 | 1 Juniper | 1 Junose | 2024-09-16 | N/A |
| Receipt of a specifically malformed IPv6 packet processed by the router may trigger a line card reset: processor exception 0x68616c74 (halt) in task: scheduler. The line card will reboot and recover without user interaction. However, additional specifically malformed packets may cause follow-on line card resets and lead to an extended service outage. This issue only affects E Series routers with IPv6 licensed and enabled. Routers not configured to process IPv6 traffic are unaffected by this vulnerability. Juniper SIRT is not aware of any malicious exploitation of this vulnerability. No other Juniper Networks products or platforms are affected by this issue. | ||||
| CVE-2021-31372 | 1 Juniper | 1 Junos | 2024-09-16 | 8.8 High |
| An Improper Input Validation vulnerability in J-Web of Juniper Networks Junos OS allows a locally authenticated J-Web attacker to escalate their privileges to root over the target device. This issue affects: Juniper Networks Junos OS All versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R3-S3; 19.3 versions prior to 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2; | ||||
| CVE-2020-1649 | 1 Juniper | 16 Junos, Mx10, Mx10000 and 13 more | 2024-09-16 | 7.5 High |
| When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(2): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1960, QID 0 [LOG: Err] MQSS(2): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0xc38fb1 [LOG: Notice] Error: /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(2), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D34, 18.2X75-D41, 18.2X75-D53, 18.2X75-D65, 18.2X75-D430 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2 on MX Series; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability. | ||||
| CVE-2022-22211 | 1 Juniper | 18 Junos Os Evolved, Ptx1000, Ptx1000-72q and 15 more | 2024-09-16 | 7.5 High |
| A limitless resource allocation vulnerability in FPC resources of Juniper Networks Junos OS Evolved on PTX Series allows an unprivileged attacker to cause Denial of Service (DoS). Continuously polling the SNMP jnxCosQstatTable causes the FPC to run out of GUID space, causing a Denial of Service to the FPC resources. When the FPC runs out of the GUID space, you will see the following syslog messages. The evo-aftmand-bt process is asserting. fpc1 evo-aftmand-bt[17556]: %USER-3: get_next_guid: Ran out of Guid Space start 1748051689472 end 1752346656767 fpc1 audit[17556]: %AUTH-5: ANOM_ABEND auid=4294967295 uid=0 gid=0 ses=4294967295 pid=17556 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=6 fpc1 kernel: %KERN-5: audit: type=1701 audit(1648567505.119:57): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=17556 comm="EvoAftManBt-mai" exe="/usr/sbin/evo-aftmand-bt" sig=6 fpc1 emfd-fpa[14438]: %USER-5: Alarm set: APP color=red, class=CHASSIS, reason=Application evo-aftmand-bt fail on node Fpc1 fpc1 emfd-fpa[14438]: %USER-3-EMF_FPA_ALARM_REP: RaiseAlarm: Alarm(Location: /Chassis[0]/Fpc[1] Module: sysman Object: evo-aftmand-bt:0 Error: 2) reported fpc1 sysepochman[12738]: %USER-5-SYSTEM_REBOOT_EVENT: Reboot [node] [ungraceful reboot] [evo-aftmand-bt exited] The FPC resources can be monitored using the following commands: user@router> start shell [vrf:none] user@router-re0:~$ cli -c "show platform application-info allocations app evo-aftmand-bt" | grep ^fpc | grep -v Route | grep -i -v Nexthop | awk '{total[$1] += $5} END { for (key in total) { print key " " total[key]/4294967296 }}' Once the FPCs become unreachable they must be manually restarted as they do not self-recover. This issue affects Juniper Networks Junos OS Evolved on PTX Series: All versions prior to 20.4R3-S4-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO version 21.2R1-EVO and later versions; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R2-EVO; 22.1-EVO versions prior to 22.1R2-EVO. | ||||
| CVE-2019-0031 | 1 Juniper | 1 Junos | 2024-09-16 | 7.5 High |
| Specific IPv6 DHCP packets received by the jdhcpd daemon will cause a memory resource consumption issue to occur on a Junos OS device using the jdhcpd daemon configured to respond to IPv6 requests. Once started, memory consumption will eventually impact any IPv4 or IPv6 request serviced by the jdhcpd daemon, thus creating a Denial of Service (DoS) condition to clients requesting and not receiving IP addresses. Additionally, some clients which were previously holding IPv6 addresses will not have their IPv6 Identity Association (IA) address and network tables agreed upon by the jdhcpd daemon after the failover event occurs, which leads to more than one interface, and multiple IP addresses, being denied on the client. Affected releases are Juniper Networks Junos OS: 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R2. | ||||