| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: add HE 6 GHz capability in the scan elems len
The HE 6 GHz Band Capability element is in the probe request for
every band if 6 GHz is supported, so add the size to scan_ies_len.
Otherwise, building probe request elements can fail, triggering the
WARN_ON in __ieee80211_start_scan(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: mesh: reset the CSA state when leaving
ifmsh->csa is allocated in ieee80211_mesh_csa_beacon() and only freed
in ieee80211_mesh_finish_csa(), i.e. when the channel switch completes.
Leaving the mesh while a switch is still pending therefore leaks it.
Additionally, ifmsh->csa_role and ifmsh->chsw_ttl have their state leak
in this case, so things can get mixed up in addition to the memory
leak.
Refactor the reset and call it in ieee80211_stop_mesh() to fix it all. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: set up the TX info early to fix failure paths
The previous commit 2c51457d930f ("wifi: mac80211: free ack status
frame on TX header build failure") cleaned up the leak, but still
left the code a bit messy and the failed SKB didn't get reported
to userspace.
Fix this up by initialising skb->cb[] earlier, which allows using
ieee80211_free_txskb() and therefore reports it for the failure
in ieee80211_build_hdr(), and unifies the ieee80211_skb_resize()
failure path with it. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: pxa: fix double counting of the hw descriptors
pxad_alloc_desc() was converted from
kzalloc(struct_size(sw_desc, hw_desc, nb_hw_desc), GFP_NOWAIT)
to kzalloc_flex(), which sets the __counted_by() counter sw_desc->nb_desc
itself - but only where the compiler has __builtin_counted_by_ref(), so
from gcc 15.1 or clang 22.1 on. The loop below it still increments
nb_desc, which makes it come out doubled there and correct elsewhere.
nb_desc is what pxad_free_desc() iterates over and what
set_updater_desc() indexes from, so set it explicitly and drop the
increment. The error path has to lower it to the number of descriptors
allocated so far, otherwise pxad_free_desc() would free entries that were
never allocated. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_nat: fully initialise new_addr in netmap setup
nft_nat_setup_netmap() builds the mapped address in an on-stack
union nf_inet_addr. For an IPv4 mapping it writes only the 4-byte .ip
member and the loop runs a single 32-bit iteration, but it then copies
the whole 16-byte union into range->min_addr and range->max_addr, so the
upper 12 bytes reach nf_nat_setup_info() uninitialised.
KMSAN reports an uninit-value in nf_nat_setup_info() reached from
nft_nat_eval(). The IPv6 path fills all 16 bytes and is not affected.
Zero-initialise new_addr. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: hold reference on ct until flow is released
nf_ct_put() releases the ct->ext area inmediately, the rcu typesafe
semantics also allow to refer to the wrong conntrack from the flowtable
datapath. Hold reference on ct until flow is released after rcu grace
period.
Add rcu_barrier() on module exit path, to ensure pending flow entries
are release before module goes away. |
| In the Linux kernel, the following vulnerability has been resolved:
drm: Fix drm_pending_vblank_event leak in error path for out_fence_ptr
When an out_fence_ptr is provided but DRM_MODE_PAGE_FLIP_EVENT is not
set, a drm_pending_vblank_event will be allocated. If later, there is an
allocation failure or another failure at setup_out_fence(), that event
will not have base.fence set and it will not be released at
complete_signaling().
Release the event and set crtc_state->event to NULL just like in the
DRM_MODE_PAGE_FLIP_EVENT case when there is a failure at
drm_event_reserve_init(). That is, prepare_signaling() releases the
event and there is nothing to be done at complete_signaling(). Use
drm_event_cancel_free() as that will also undo drm_event_reserve_init()
in case it has been called. |
| In the Linux kernel, the following vulnerability has been resolved:
neighbour: Enforce min/max to NDTPA_INTERVAL_PROBE_TIME_MS.
NDTPA_INTERVAL_PROBE_TIME_MS sets .type and .min but misses
.validation_type, so no validation is applied:
# ynl --family rt-neigh --do setneightbl \
--json '{"name": "arp_cache", "parms": {"interval-probe-time-ms": 0}}'
# ynl --family rt-neigh --dump getneightbl --output-json | \
jq '.[] | select(.name == "arp_cache" and has("config"))
| .parms["interval-probe-time-ms"]'
0
Moreover, nla_get_msecs() uses msecs_to_jiffies(), and u64 is
silently cast to u32, so a larger value can bypass the min check:
e.g. 4294967296 == 0x100000000
# ynl --family rt-neigh --do setneightbl \
--json '{"name": "arp_cache", "parms": {"interval-probe-time-ms": 4294967296}}'
# ynl --family rt-neigh --dump getneightbl --output-json | \
jq '.[] | select(.name == "arp_cache" and has("config"))
| .parms["interval-probe-time-ms"]'
0
msecs_to_jiffies() returns MAX_JIFFY_OFFSET if the value is
larger than INT_MAX. Also, INT_MAX ms overflows int NEIGH_VAR()
when HZ > 1000 (Alpha, MIPS), and passing a negative integer to
queue_delayed_work(unsigned long delay) causes sign extension,
which wraps around the expiry time to the past, resulting in it
being handled as 0 delay in the timer wheel.
Let's use NLA_POLICY_FULL_RANGE() and limit the max to 1 day.
The same max check is applied to sysctl as well.
Note that this controls the probe interval for NTF_MANAGED
entries, so the max of 1 day is unlikely to break any
deployments. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: protect runlist updates with the runlist lock
ntfs_non_resident_attr_shrink() calls runlist helpers that require the
runlist write lock, but did not hold it while freeing clusters and
truncating the runlist. Serialize those operations and the resident
conversion with the runlist lock.
ntfs_attr_map_cluster() can merge a newly allocated run before updating
mapping pairs. If the update fails, free the clusters and restore both
the in-memory runlist and on-disk mapping pairs from a saved runlist.
Mark the volume in error if either rollback step fails. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: set timer->private_data before registering the PCM timer
snd_pcm_timer_init() calls snd_device_register() to link the new
struct snd_timer into the global timer list while it still carries
hw.c_resolution = snd_pcm_timer_resolution (and hw.start/hw.stop),
and only afterwards sets timer->private_data = substream.
Once the timer is on the list under register_mutex, a concurrent
reader can already reach it through the same mutex and invoke these
callbacks. /proc/asound/timers does this via c_resolution(), and
snd_timer_open()+snd_timer_start() reach start()/stop() the same way.
All three dereference timer->private_data, which for this brief
window is NULL, giving a NULL-pointer dereference:
substream = timer->private_data;
return substream->runtime ? ... // substream is NULL
Move the private_data/private_free assignment before
snd_device_register() so the timer is never visible on the list
without its private_data set. On the snd_device_register() failure
path, private_free() (snd_pcm_timer_free()) can now run, but it only
does substream->timer = NULL, which is already NULL at that point
since substream->timer is set to the new timer just once, after a
successful registration -- so the failure path stays safe. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dp: skip PUSH_IDLE when the link was never enabled
msm_dp_display_atomic_enable() returns early when link training fails,
leaving ->power_on false and the main link down.
msm_dp_display_atomic_disable() nevertheless writes DP_STATE_CTRL_PUSH_IDLE
and waits for an idle-pattern completion that cannot arrive, so every failed
enable is followed by "PUSH_IDLE pattern timedout".
Every other step of the teardown is already gated on that flag:
msm_dp_display_disable(), called from .atomic_post_disable(), returns early
on !power_on. The PUSH_IDLE write is the only one that is not, so the
controller's runtime-PM reference is then dropped without the link having
been taken down.
On glymur (Snapdragon X2 Elite) the consequence is not a warning. The SoC
does not survive it: TrustZone force-stops the SOCCP and ADSP remote
processors and the machine resets silently about 50 ms later, with no oops
and no panic. On an ASUS Zenbook A16 (UX3607OA), whose eDP panel does not
currently train, this reproduces without any compositor or GPU involvement:
# eDP enable has already failed with "Failed link training (rc=-104)"
echo 1 > /sys/class/graphics/fb0/blank
[535.645455] === marker ===
[535.694833] qcom_q6v5_pas d00000.remoteproc: fatal error received: \
sys_m_smsm.c:512:TZ force stop
[535.694875] remoteproc remoteproc0: crash detected in soccp: type fatal error
[535.728857] qcom_q6v5_pas 6800000.remoteproc: fatal error received: \
sys_m_smsm.c:783:err fatal notification received from TZ
<SoC reset>
Gate the PUSH_IDLE write on ->power_on so the disable path is consistent
with the rest of the teardown. With this applied the same sequence is
harmless and the machine stays up; without it, it resets every time.
The unconditional write dates back to the original DP driver
(c943b4948b58 ("drm/msm/dp: add displayPort driver support")), but the
surrounding code has been restructured several times since, so no Fixes:
tag is offered.
Note that the eDP link-training failure that exposes this on the A16 is a
separate problem in the glymur eDP PHY and is reported separately; this
change is about not damaging the machine when training fails, for whatever
reason.
Tested on ASUS Zenbook A16 (UX3607OA), Snapdragon X2 Elite Extreme, on
linux-next next-20260803 and next-20260807. The machine has since been
running next-20260807 with this patch as its daily driver.
Patchwork: https://patchwork.freedesktop.org/patch/745167/ |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: virt_wifi: don't transfer operstate before register
virt_wifi_newlink() calls netif_stacked_transfer_operstate() before
register_netdevice(). If the lower device is dormant, that queues the
new netdev on lweventlist while it is still uninitialized. If
registration fails after that, for example because of an invalid name
such as "bad/name", free_netdev() immediately frees the object. A
later linkwatch_fire_event() then use-after-frees the list entry.
Move the transfer to after netdev_upper_dev_link(), as macvlan and
ipvlan already do. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/shrinker: Take a runtime PM ref before shrinking non-system memory
__xe_shrinker_walk() walks the SYSTEM and TT LRUs without a runtime PM
reference. Shrinking a bo outside system memory invalidates its GPU
mappings, which needs the device resumed, so while it is runtime
suspended the page table zap trips an assert and the TLB invalidation
returns -ENODEV:
WARNING: drivers/gpu/drm/xe/xe_bo.c:770 at xe_bo_move_notify+0x1fc/0x450 [xe]
xe_bo_shrink+0x20f/0x2b0 [xe]
__xe_shrinker_walk+0x174/0x410 [xe]
xe_shrinker_scan+0x10c/0x1e0 [xe]
do_shrink_slab+0x176/0x7e0
drop_caches_sysctl_handler+0x9c/0xf0
Take a reference before walking a memory type other than XE_PL_SYSTEM
and stop there if it cannot be acquired. Reuse the shrinker's existing
acquire path, which resumes the device directly where reclaim allows
that and otherwise queues the PM worker for a later scan. Stop the walk
once the scan target is met, so a satisfied scan does not wake the
device. System memory is still reclaimed while the device is suspended.
Gate this on xe_device_is_l2_flush_optimized(), the same condition under
which xe_bo_trigger_rebind() issues the invalidation for a non-fault-mode
vm, so reclaim is unaffected elsewhere. The System CCS copy already has
its own reference in xe_bo_shrink().
Only a non-fault-mode vm can reach this, since a fault-mode vm requires
LR mode and that holds a runtime PM reference for the vm's lifetime.
Reproduced with igt@xe_madvise@dontneed-before-exec while the GPU is
runtime suspended.
v2: simplify needs_rpm check. (Matt)
retarget Fixes tag since the issue occurs with the non-fault-mode
path added by 4e7ebff69aed.
v3: handle this in xe_shrinker.c instead of xe_bo.c (Thomas)
v4: stop the walk once the scan target is met. (Sashiko)
v5: rebase on the freed page accounting fix. (Sashiko)
v6: reuse the shrinker acquire path so runtime pm can be resumed
directly instead of always queueing a worker. (Thomas)
v7: replace xe_pm_runtime_put() with xe_shrinker_runtime_pm_put(). (Thomas)
(cherry picked from commit 628f92b28bf4c371c10207daf6fc4caee0c0db2e) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: Use managed KMS polling to fix UAF on unbind
vc4_kms_load() calls drm_kms_helper_poll_init() but the driver provides
no matching drm_kms_helper_poll_fini(). The output poll work stays
scheduled after unbind and runs on the freed drm_device:
# modprobe vc4; rmmod vc4; sleep 10
BUG: KASAN: slab-use-after-free in delayed_work_timer_fn
BUG: KASAN: slab-use-after-free in drm_client_dev_hotplug [drm]
Workqueue: events output_poll_execute [drm_kms_helper]
Allocated by task 171: __devm_drm_dev_alloc
Freed by task 262 (rmmod): drm_dev_put / component_del
Use drmm_kms_helper_poll_init() so polling is finalized with the device,
as other drivers do. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: mxl862xx: disable the stats poll on teardown
mxl862xx_setup() arms the stats poll before mxl862xx_setup_mdio(), and
nothing stops it until dsa_register_switch() has returned an error to
mxl862xx_probe(). DSA frees the dsa_port list before it returns, so a
poll that fires once .setup or a later step of dsa_tree_setup() has
failed walks freed ports. On shutdown the user ports stay registered,
and the WORK_STOPPED flag test in mxl862xx_get_stats64() is not atomic
with the cancel in mxl862xx_shutdown(), so a re-arm that read the flag
before it was set queues the poll after cancel_delayed_work_sync() has
returned.
Arm the poll once .setup has succeeded and stop it from a .teardown op,
which DSA calls on unregister and after a failed registration, in both
cases before it frees the ports. Use disable_delayed_work_sync() there
and in shutdown(): it drains a running poll as the cancel did and turns
every later attempt to queue the work into a no-op, so the re-arm
cannot bring the poll back. remove() and the probe error path only set
WORK_STOPPED, which crc_err_work tests before it walks the ports. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: restore the hardware filters on open
bcmgenet_hfb_init() runs INIT_LIST_HEAD() on priv->rxnfc_list, which drops
every rule off the list, and bcmgenet_open() calls it on each ifup. Every
rule the user configured is silently lost:
# ethtool -N eth0 flow-type ether dst $MAC action 0
Added rule with ID 0
# ethtool -n eth0 | grep -c Filter:
1
# ip link set eth0 down && ip link set eth0 up
# ethtool -n eth0 | grep -c Filter:
0
Initialise the lists once at probe and restore the rules on open, as
bcmgenet_resume() already does. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: icmp: reject RTN_UNREACHABLE input routes in icmp_route_lookup
When the forward output route cannot be used in icmp_route_lookup(),
it enters the "reverse path" and calls ip_route_input() on fl4_dec.daddr,
the original packet's source address.
ip_route_input() only returns an error for truly invalid packets. For
unreachable addresses it will succeed and return an input route whose
dst.output is set to ip_rt_bug(). The existing check only rejects
RTN_LOCAL routes, so the RTN_UNREACHABLE route types can still be returned
and later used for output, syzkaller triggering a WARN_ON_ONCE()
in ip_rt_bug() as bellow:
------------[ cut here ]------------
WARNING: net/ipv4/route.c:1273 at ip_rt_bug+0x14/0x20
RIP: 0010:ip_rt_bug+0x14/0x20
Call Trace:
ip_push_pending_frames+0xfa/0x100
__icmp_send+0x905/0xf10
ip_options_compile+0xc0/0xd0
ip_rcv_finish_core+0x321/0xae0
ip_rcv+0x1de/0x260
__netif_receive_skb_one_core+0x11a/0x130
netif_receive_skb+0x7b/0x260
tun_get_user+0x11bf/0x1c10
------------[ cut here ]------------
Reject input route that is RTN_UNREACHABLE to fix it. The net warning
is only printed for RTN_LOCAL, as RTN_UNREACHABLE is not the result of
a race condition. |
| In the Linux kernel, the following vulnerability has been resolved:
net: fddi: skfp: fix NULL deref when setting the MAC address while down
skfp_ctl_set_mac_address() calls ResetAdapter() unconditionally, without
checking netif_running(). ResetAdapter() first calls card_stop(), which
sets smc->hw.hw_state to STOPPED, and then mac_drv_clear_tx_queue(),
which walks the two transmit queues:
for (i = QUEUE_S; i <= QUEUE_A0; i++) {
queue = smc->hw.fp.tx[i] ;
...
t = queue->tx_curr_get ;
smc->hw.fp.tx[] is only populated by init_tx(), which is reached from
skfp_open() through init_smt() -> init_fddi_driver() -> init_fplus() ->
init_mac() -> init_tx(). The private area is allocated and zeroed by
alloc_fddidev(), so on an interface that has never been brought up both
queue pointers are still NULL. The hw_state test at the top of
mac_drv_clear_tx_queue() does not catch this, because card_stop() has
just set STOPPED; the function proceeds into the loop and dereferences
NULL. ResetAdapter() does call init_smt() itself, but only after the
queues have been cleared.
Setting the MAC address on a down interface therefore oopses:
ip link set dev fddi0 address 02:00:00:00:00:01
BUG: KASAN: null-ptr-deref in mac_drv_clear_tx_queue+0x68/0x2c0 [skfp]
Read of size 8 at addr 0000000000000010 by task ip/302
Call Trace:
<TASK>
mac_drv_clear_tx_queue+0x68/0x2c0 [skfp 6c01d4bab63c36978bd0a7d7e90837adb44cc37b]
ResetAdapter+0x29/0x100 [skfp 6c01d4bab63c36978bd0a7d7e90837adb44cc37b]
skfp_ctl_set_mac_address+0x57/0x80 [skfp 6c01d4bab63c36978bd0a7d7e90837adb44cc37b]
netif_set_mac_address+0x1e4/0x2c0
do_setlink+0x684/0x2680
</TASK>
Address 0x10 is the offset of tx_curr_get, the third pointer in
struct s_smt_tx_queue, on 64-bit. mac_drv_clear_rx_queue(), which
ResetAdapter() calls immediately afterwards, dereferences
smc->hw.fp.rx[QUEUE_R1] in the same way behind the same ineffective
hw_state test; the transmit queue merely crashes first. Both are
covered by the guard below.
Skip the adapter reset when the interface is down. dev_addr_set() is
left unconditional, so the new address is still recorded in
dev->dev_addr. Nothing is lost by not resetting the adapter here:
skfp_open() deliberately re-reads the factory address on every open,
read_address(smc, NULL);
eth_hw_addr_set(dev, smc->hw.fddi_canon_addr.a);
and the comment above it states this is done to discard exactly such an
address override across a close/open cycle. An address set while the
interface is down could not have survived the following open even
before this change, so the guard removes no working behaviour. Guarding
the hardware side of ndo_set_mac_address() with netif_running() is
established practice; skge_set_mac_address() has done so since commit
2eb3e621c4e0 ("skge: set mac address bonding fix").
Guarding the reset as a whole, rather than NULL-checking the queues, is
also what the rest of the driver expects. After a previous open/close
the queue pointers are stale but non-NULL, so there is no crash, yet
ResetAdapter() goes on to call smt_online() and STI_FBI() ("Enable
Board Interrupts") while skfp_close() has already called free_irq() -
the adapter would be brought back online with no handler installed. The
only other ResetAdapter() caller is skfp_interrupt(), which by
construction runs only while the device is open.
Found by automated driver testing against an emulated SysKonnect FDDI
adapter under a KASAN-enabled 7.0.0 kernel. Triggering it requires
CAP_NET_ADMIN. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: mst: move switchdev call outside rcu
This is a follow-up of one of sashiko's pre-existing bug reports.
br_mst_set_state() calls switchdev_port_attr_set() for nonzero MSTIs
while holding rcu_read_lock() which invokes the blocking switchdev
notifier chain and may sleep. Nonzero MSTI changes come from netlink
with rtnl held. Move the switchdev call before entering the rcu section and
assert that rtnl is held.
The call cannot be deferred because netlink needs its error and extack.
Also DSA reads the old bridge MST state during the callback and checks it.
A deferred callback will be late and will see the updated state. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: Don't call skb_clone_and_charge_r() for close()d listener in tcp_v6_do_rcv().
tcp_v6_do_rcv() no longer calls skb_clone_and_charge_r() for
TCP_LISTEN since commit 073d89808c06 ("net: fix data-races around
sk->sk_forward_alloc").
However, there is still a small race window between tcp_v6_rcv()
and tcp_v6_do_rcv(), where concurrent close() changes TCP_LISTEN
to TCP_CLOSE, causing skb_clone_and_charge_r() to be called
locklessly and resulting in the splat below. [0]
Let's avoid calling skb_clone_and_charge_r() for TCP_CLOSE as well.
This is fine for non-listeners because tcp_rcv_state_process()
drops skb for TCP_CLOSE and opt_skb was freed immediately anyway.
[0]:
sk->sk_forward_alloc
WARNING: net/ipv4/af_inet.c:162 at inet_sock_destruct+0x64d/0x810 net/ipv4/af_inet.c:162, CPU#1: ksoftirqd/1/28
Modules linked in:
CPU: 1 UID: 0 PID: 28 Comm: ksoftirqd/1 Not tainted 7.2.0 #17 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-debian-1.17.0-1 04/01/2014
RIP: 0010:inet_sock_destruct+0x64d/0x810 net/ipv4/af_inet.c:162
Code: 3d 49 ff e9 06 fd ff ff e8 d0 5b 83 f8 90 0f 0b 90 e9 35 fe ff ff e8 c2 5b 83 f8 90 0f 0b 90 e9 c5 fe ff ff e8 b4 5b 83 f8 90 <0f> 0b 90 e9 04 ff ff ff e8 a6 5b 83 f8 90 0f 0b 90 e9 65 fe ff ff
RSP: 0018:ffffc90000677bb8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8880117bde80 RCX: ffffffff8957eb41
RDX: ffff88801dad5d00 RSI: ffffffff8957ec3c RDI: 0000000000000005
RBP: 00000000fffff000 R08: ffffffff8957eb41 R09: 00000000fffff000
R10: 0000000000000005 R11: 0000000000000000 R12: dffffc0000000000
R13: ffff8880117bdf10 R14: ffffffff81c08eb7 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff8880d7ae5000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f93a1021138 CR3: 00000000207a9000 CR4: 0000000000350ef0
Call Trace:
<TASK>
__sk_destruct+0x82/0xae0 net/core/sock.c:2356
rcu_do_batch kernel/rcu/tree.c:2645 [inline]
rcu_core+0x59c/0x1100 kernel/rcu/tree.c:2897
handle_softirqs+0x1e4/0x9b0 kernel/softirq.c:622
run_ksoftirqd kernel/softirq.c:1076 [inline]
run_ksoftirqd+0x38/0x60 kernel/softirq.c:1068
smpboot_thread_fn+0x458/0xc80 kernel/smpboot.c:160
kthread+0x396/0x4a0 kernel/kthread.c:436
ret_from_fork+0x8e0/0xe40 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK> |
