| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: mpu3050: Move iio_device_register() to correct location
iio_device_register() should be at the end of the probe function to
prevent race conditions.
Place iio_device_register() at the end of the probe function and place
iio_device_unregister() accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: mpu3050: Fix irq resource leak
The interrupt handler is setup but only a few lines down if
iio_trigger_register() fails the function returns without properly
releasing the handler.
Add cleanup goto to resolve resource leak.
Detected by Smatch:
drivers/iio/gyro/mpu3050-core.c:1128 mpu3050_trigger_probe() warn:
'irq' from request_threaded_irq() not released on lines: 1124. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: mpu3050: Fix incorrect free_irq() variable
The handler for the IRQ part of this driver is mpu3050->trig but,
in the teardown free_irq() is called with handler mpu3050.
Use correct IRQ handler when calling free_irq(). |
| In the Linux kernel, the following vulnerability has been resolved:
iio: imu: st_lsm6dsx: Set buffer sampling frequency for accelerometer only
The st_lsm6dsx_hwfifo_odr_store() function, which is called when userspace
writes the buffer sampling frequency sysfs attribute, calls
st_lsm6dsx_check_odr(), which accesses the odr_table array at index
`sensor->id`; since this array is only 2 entries long, an access for any
sensor type other than accelerometer or gyroscope is an out-of-bounds
access.
The motivation for being able to set a buffer frequency different from the
sensor sampling frequency is to support use cases that need accurate event
detection (which requires a high sampling frequency) while retrieving
sensor data at low frequency. Since all the supported event types are
generated from acceleration data only, do not create the buffer sampling
frequency attribute for sensor types other than the accelerometer. |
| In the Linux kernel, the following vulnerability has been resolved:
pstore: ram_core: fix incorrect success return when vmap() fails
In persistent_ram_vmap(), vmap() may return NULL on failure.
If offset is non-zero, adding offset_in_page(start) causes the function
to return a non-NULL pointer even though the mapping failed.
persistent_ram_buffer_map() therefore incorrectly returns success.
Subsequent access to prz->buffer may dereference an invalid address
and cause crashes.
Add proper NULL checking for vmap() failures. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-pci: Fix race bug in nvme_poll_irqdisable()
In the following scenario, pdev can be disabled between (1) and (3) by
(2). This sets pdev->msix_enabled = 0. Then, pci_irq_vector() will
return MSI-X IRQ(>15) for (1) whereas return INTx IRQ(<=15) for (2).
This causes IRQ warning because it tries to enable INTx IRQ that has
never been disabled before.
To fix this, save IRQ number into a local variable and ensure
disable_irq() and enable_irq() operate on the same IRQ number. Even if
pci_free_irq_vectors() frees the IRQ concurrently, disable_irq() and
enable_irq() on a stale IRQ number is still valid and safe, and the
depth accounting reamins balanced.
task 1:
nvme_poll_irqdisable()
disable_irq(pci_irq_vector(pdev, nvmeq->cq_vector)) ...(1)
enable_irq(pci_irq_vector(pdev, nvmeq->cq_vector)) ...(3)
task 2:
nvme_reset_work()
nvme_dev_disable()
pdev->msix_enable = 0; ...(2)
crash log:
------------[ cut here ]------------
Unbalanced enable for IRQ 10
WARNING: kernel/irq/manage.c:753 at __enable_irq+0x102/0x190 kernel/irq/manage.c:753, CPU#1: kworker/1:0H/26
Modules linked in:
CPU: 1 UID: 0 PID: 26 Comm: kworker/1:0H Not tainted 6.19.0-dirty #9 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
Workqueue: kblockd blk_mq_timeout_work
RIP: 0010:__enable_irq+0x107/0x190 kernel/irq/manage.c:753
Code: ff df 48 89 fa 48 c1 ea 03 0f b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 04 84 d2 75 79 48 8d 3d 2e 7a 3f 05 41 8b 74 24 2c <67> 48 0f b9 3a e8 ef b9 21 00 5b 41 5c 5d e9 46 54 66 03 e8 e1 b9
RSP: 0018:ffffc900001bf550 EFLAGS: 00010046
RAX: 0000000000000007 RBX: 0000000000000000 RCX: ffffffffb20c0e90
RDX: 0000000000000000 RSI: 000000000000000a RDI: ffffffffb74b88f0
RBP: ffffc900001bf560 R08: ffff88800197cf00 R09: 0000000000000001
R10: 0000000000000003 R11: 0000000000000003 R12: ffff8880012a6000
R13: 1ffff92000037eae R14: 000000000000000a R15: 0000000000000293
FS: 0000000000000000(0000) GS:ffff8880b49f7000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000555da4a25fa8 CR3: 00000000208e8000 CR4: 00000000000006f0
Call Trace:
<TASK>
enable_irq+0x121/0x1e0 kernel/irq/manage.c:797
nvme_poll_irqdisable+0x162/0x1c0 drivers/nvme/host/pci.c:1494
nvme_timeout+0x965/0x14b0 drivers/nvme/host/pci.c:1744
blk_mq_rq_timed_out block/blk-mq.c:1653 [inline]
blk_mq_handle_expired+0x227/0x2d0 block/blk-mq.c:1721
bt_iter+0x2fc/0x3a0 block/blk-mq-tag.c:292
__sbitmap_for_each_set include/linux/sbitmap.h:269 [inline]
sbitmap_for_each_set include/linux/sbitmap.h:290 [inline]
bt_for_each block/blk-mq-tag.c:324 [inline]
blk_mq_queue_tag_busy_iter+0x969/0x1e80 block/blk-mq-tag.c:536
blk_mq_timeout_work+0x627/0x870 block/blk-mq.c:1763
process_one_work+0x956/0x1aa0 kernel/workqueue.c:3257
process_scheduled_works kernel/workqueue.c:3340 [inline]
worker_thread+0x65c/0xe60 kernel/workqueue.c:3421
kthread+0x41a/0x930 kernel/kthread.c:463
ret_from_fork+0x6f8/0x8c0 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246
</TASK>
irq event stamp: 74478
hardirqs last enabled at (74477): [<ffffffffb5720a9c>] __raw_spin_unlock_irq include/linux/spinlock_api_smp.h:159 [inline]
hardirqs last enabled at (74477): [<ffffffffb5720a9c>] _raw_spin_unlock_irq+0x2c/0x60 kernel/locking/spinlock.c:202
hardirqs last disabled at (74478): [<ffffffffb57207b5>] __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:108 [inline]
hardirqs last disabled at (74478): [<ffffffffb57207b5>] _raw_spin_lock_irqsave+0x85/0xa0 kernel/locking/spinlock.c:162
softirqs last enabled at (74304): [<ffffffffb1e9466c>] __do_softirq kernel/softirq.c:656 [inline]
softirqs last enabled at (74304): [<ffffffffb1e9466c>] invoke_softirq kernel/softirq.c:496 [inline]
softirqs last enabled at (74304): [<ffffffffb1e9466c>] __irq_exit_rcu+0xdc/0x120
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_queue: fix entry leak in bridge verdict error path
nfqnl_recv_verdict() calls find_dequeue_entry() to remove the queue
entry from the queue data structures, taking ownership of the entry.
For PF_BRIDGE packets, it then calls nfqa_parse_bridge() to parse VLAN
attributes. If nfqa_parse_bridge() returns an error (e.g. NFQA_VLAN
present but NFQA_VLAN_TCI missing), the function returns immediately
without freeing the dequeued entry or its sk_buff.
This leaks the nf_queue_entry, its associated sk_buff, and all held
references (net_device refcounts, struct net refcount). Repeated
triggering exhausts kernel memory.
Fix this by dropping the entry via nfqnl_reinject() with NF_DROP verdict
on the error path, consistent with other error handling in this file. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: Fix for duplicate device in netdev hooks
When handling NETDEV_REGISTER notification, duplicate device
registration must be avoided since the device may have been added by
nft_netdev_hook_alloc() already when creating the hook. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: rockchip-sfc: Fix double-free in remove() callback
The driver uses devm_spi_register_controller() for registration, which
automatically unregisters the controller via devm cleanup when the
device is removed. The manual call to spi_unregister_controller() in
the remove() callback can lead to a double-free.
And to make sure controller is unregistered before DMA buffer is
unmapped, switch to use spi_register_controller() in probe(). |
| In the Linux kernel, the following vulnerability has been resolved:
spi: amlogic: spifc-a4: Fix DMA mapping error handling
Fix three bugs in aml_sfc_dma_buffer_setup() error paths:
1. Unnecessary goto: When the first DMA mapping (sfc->daddr) fails,
nothing needs cleanup. Use direct return instead of goto.
2. Double-unmap bug: When info DMA mapping failed, the code would
unmap sfc->daddr inline, then fall through to out_map_data which
would unmap it again, causing a double-unmap.
3. Wrong unmap size: The out_map_info label used datalen instead of
infolen when unmapping sfc->iaddr, which could lead to incorrect
DMA sync behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
net: spacemit: Fix error handling in emac_tx_mem_map()
The DMA mappings were leaked on mapping error. Free them with the
existing emac_free_tx_buf() function. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: storvsc: Fix scheduling while atomic on PREEMPT_RT
This resolves the follow splat and lock-up when running with PREEMPT_RT
enabled on Hyper-V:
[ 415.140818] BUG: scheduling while atomic: stress-ng-iomix/1048/0x00000002
[ 415.140822] INFO: lockdep is turned off.
[ 415.140823] Modules linked in: intel_rapl_msr intel_rapl_common intel_uncore_frequency_common intel_pmc_core pmt_telemetry pmt_discovery pmt_class intel_pmc_ssram_telemetry intel_vsec ghash_clmulni_intel aesni_intel rapl binfmt_misc nls_ascii nls_cp437 vfat fat snd_pcm hyperv_drm snd_timer drm_client_lib drm_shmem_helper snd sg soundcore drm_kms_helper pcspkr hv_balloon hv_utils evdev joydev drm configfs efi_pstore nfnetlink vsock_loopback vmw_vsock_virtio_transport_common hv_sock vmw_vsock_vmci_transport vsock vmw_vmci efivarfs autofs4 ext4 crc16 mbcache jbd2 sr_mod sd_mod cdrom hv_storvsc serio_raw hid_generic scsi_transport_fc hid_hyperv scsi_mod hid hv_netvsc hyperv_keyboard scsi_common
[ 415.140846] Preemption disabled at:
[ 415.140847] [<ffffffffc0656171>] storvsc_queuecommand+0x2e1/0xbe0 [hv_storvsc]
[ 415.140854] CPU: 8 UID: 0 PID: 1048 Comm: stress-ng-iomix Not tainted 6.19.0-rc7 #30 PREEMPT_{RT,(full)}
[ 415.140856] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 09/04/2024
[ 415.140857] Call Trace:
[ 415.140861] <TASK>
[ 415.140861] ? storvsc_queuecommand+0x2e1/0xbe0 [hv_storvsc]
[ 415.140863] dump_stack_lvl+0x91/0xb0
[ 415.140870] __schedule_bug+0x9c/0xc0
[ 415.140875] __schedule+0xdf6/0x1300
[ 415.140877] ? rtlock_slowlock_locked+0x56c/0x1980
[ 415.140879] ? rcu_is_watching+0x12/0x60
[ 415.140883] schedule_rtlock+0x21/0x40
[ 415.140885] rtlock_slowlock_locked+0x502/0x1980
[ 415.140891] rt_spin_lock+0x89/0x1e0
[ 415.140893] hv_ringbuffer_write+0x87/0x2a0
[ 415.140899] vmbus_sendpacket_mpb_desc+0xb6/0xe0
[ 415.140900] ? rcu_is_watching+0x12/0x60
[ 415.140902] storvsc_queuecommand+0x669/0xbe0 [hv_storvsc]
[ 415.140904] ? HARDIRQ_verbose+0x10/0x10
[ 415.140908] ? __rq_qos_issue+0x28/0x40
[ 415.140911] scsi_queue_rq+0x760/0xd80 [scsi_mod]
[ 415.140926] __blk_mq_issue_directly+0x4a/0xc0
[ 415.140928] blk_mq_issue_direct+0x87/0x2b0
[ 415.140931] blk_mq_dispatch_queue_requests+0x120/0x440
[ 415.140933] blk_mq_flush_plug_list+0x7a/0x1a0
[ 415.140935] __blk_flush_plug+0xf4/0x150
[ 415.140940] __submit_bio+0x2b2/0x5c0
[ 415.140944] ? submit_bio_noacct_nocheck+0x272/0x360
[ 415.140946] submit_bio_noacct_nocheck+0x272/0x360
[ 415.140951] ext4_read_bh_lock+0x3e/0x60 [ext4]
[ 415.140995] ext4_block_write_begin+0x396/0x650 [ext4]
[ 415.141018] ? __pfx_ext4_da_get_block_prep+0x10/0x10 [ext4]
[ 415.141038] ext4_da_write_begin+0x1c4/0x350 [ext4]
[ 415.141060] generic_perform_write+0x14e/0x2c0
[ 415.141065] ext4_buffered_write_iter+0x6b/0x120 [ext4]
[ 415.141083] vfs_write+0x2ca/0x570
[ 415.141087] ksys_write+0x76/0xf0
[ 415.141089] do_syscall_64+0x99/0x1490
[ 415.141093] ? rcu_is_watching+0x12/0x60
[ 415.141095] ? finish_task_switch.isra.0+0xdf/0x3d0
[ 415.141097] ? rcu_is_watching+0x12/0x60
[ 415.141098] ? lock_release+0x1f0/0x2a0
[ 415.141100] ? rcu_is_watching+0x12/0x60
[ 415.141101] ? finish_task_switch.isra.0+0xe4/0x3d0
[ 415.141103] ? rcu_is_watching+0x12/0x60
[ 415.141104] ? __schedule+0xb34/0x1300
[ 415.141106] ? hrtimer_try_to_cancel+0x1d/0x170
[ 415.141109] ? do_nanosleep+0x8b/0x160
[ 415.141111] ? hrtimer_nanosleep+0x89/0x100
[ 415.141114] ? __pfx_hrtimer_wakeup+0x10/0x10
[ 415.141116] ? xfd_validate_state+0x26/0x90
[ 415.141118] ? rcu_is_watching+0x12/0x60
[ 415.141120] ? do_syscall_64+0x1e0/0x1490
[ 415.141121] ? do_syscall_64+0x1e0/0x1490
[ 415.141123] ? rcu_is_watching+0x12/0x60
[ 415.141124] ? do_syscall_64+0x1e0/0x1490
[ 415.141125] ? do_syscall_64+0x1e0/0x1490
[ 415.141127] ? irqentry_exit+0x140/0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wl1251: validate packet IDs before indexing tx_frames
wl1251_tx_packet_cb() uses the firmware completion ID directly to index
the fixed 16-entry wl->tx_frames[] array. The ID is a raw u8 from the
completion block, and the callback does not currently verify that it
fits the array before dereferencing it.
Reject completion IDs that fall outside wl->tx_frames[] and keep the
existing NULL check in the same guard. This keeps the fix local to the
trust boundary and avoids touching the rest of the completion flow. |
| The CloudStack Backup plugin has an improper authorization logic in versions 4.21.0.0 and 4.22.0.0. Anyone with authenticated user-account access in CloudStack 4.21.0.0+ environments, where this plugin is enabled and has access to specific APIs can list backups from any account in the environment. This vulnerability does not allow them to see the contents of the backup.
Users are recommended to upgrade to version 4.22.0.1, which fixes the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: mixer: oss: Add card disconnect checkpoints
ALSA OSS mixer layer calls the kcontrol ops rather individually, and
pending calls might be not always caught at disconnecting the device.
For avoiding the potential UAF scenarios, add sanity checks of the
card disconnection at each entry point of OSS mixer accesses. The
rwsem is taken just before that check, hence the rest context should
be covered by that properly. |
| The CloudStack Backup plugin has an improper access logic in versions 4.21.0.0 and 4.22.0.0. Anyone with authenticated user-account access in CloudStack 4.21.0.0+ environments, where this plugin is enabled and have access to specific APIs can create new VMs using backups of any other user of the environment.
Backup plugin users using CloudStack 4.21.0.0+ are recommended to upgrade to CloudStack version 4.22.0.1, which fixes this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs3: fix circular locking dependency in run_unpack_ex
Syzbot reported a circular locking dependency between wnd->rw_lock
(sbi->used.bitmap) and ni->file.run_lock.
The deadlock scenario:
1. ntfs_extend_mft() takes ni->file.run_lock then wnd->rw_lock.
2. run_unpack_ex() takes wnd->rw_lock then tries to acquire
ni->file.run_lock inside ntfs_refresh_zone().
This creates an AB-BA deadlock.
Fix this by using down_read_trylock() instead of down_read() when
acquiring run_lock in run_unpack_ex(). If the lock is contended,
skip ntfs_refresh_zone() - the MFT zone will be refreshed on the
next MFT operation. This breaks the circular dependency since we
never block waiting for run_lock while holding wnd->rw_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_set_pipapo_avx2: don't return non-matching entry on expiry
New test case fails unexpectedly when avx2 matching functions are used.
The test first loads a ranomly generated pipapo set
with 'ipv4 . port' key, i.e. nft -f foo.
This works. Then, it reloads the set after a flush:
(echo flush set t s; cat foo) | nft -f -
This is expected to work, because its the same set after all and it was
already loaded once.
But with avx2, this fails: nft reports a clashing element.
The reported clash is of following form:
We successfully re-inserted
a . b
c . d
Then we try to insert a . d
avx2 finds the already existing a . d, which (due to 'flush set') is marked
as invalid in the new generation. It skips the element and moves to next.
Due to incorrect masking, the skip-step finds the next matching
element *only considering the first field*,
i.e. we return the already reinserted "a . b", even though the
last field is different and the entry should not have been matched.
No such error is reported for the generic c implementation (no avx2) or when
the last field has to use the 'nft_pipapo_avx2_lookup_slow' fallback.
Bisection points to
7711f4bb4b36 ("netfilter: nft_set_pipapo: fix range overlap detection")
but that fix merely uncovers this bug.
Before this commit, the wrong element is returned, but erronously
reported as a full, identical duplicate.
The root-cause is too early return in the avx2 match functions.
When we process the last field, we should continue to process data
until the entire input size has been consumed to make sure no stale
bits remain in the map. |
| The CloudStack Backup plugin has an improper access logic in versions 4.21.0.0 and 4.22.0.0. Anyone with authenticated user-account access in CloudStack 4.21.0.0+ environments, where this plugin is enabled and have access to specific APIs can restore a volume from any other user's backups and attach the volume to their own VMs.
Backup plugin users using CloudStack 4.21.0.0+ are recommended to upgrade to CloudStack version 4.22.0.1, which fixes this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/umem: Fix double dma_buf_unpin in failure path
In ib_umem_dmabuf_get_pinned_with_dma_device(), the call to
ib_umem_dmabuf_map_pages() can fail. If this occurs, the dmabuf
is immediately unpinned but the umem_dmabuf->pinned flag is still
set. Then, when ib_umem_release() is called, it calls
ib_umem_dmabuf_revoke() which will call dma_buf_unpin() again.
Fix this by removing the immediate unpin upon failure and just let
the ib_umem_release/revoke path handle it. This also ensures the
proper unmap-unpin unwind ordering if the dmabuf_map_pages call
happened to fail due to dma_resv_wait_timeout (and therefore has
a non-NULL umem_dmabuf->sgt). |
