Filtered by vendor Juniper
Subscriptions
Filtered by product Junos
Subscriptions
Total
611 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2021-31371 | 1 Juniper | 6 Junos, Qfx5100, Qfx5110 and 3 more | 2024-09-17 | 5.3 Medium |
| Juniper Networks Junos OS uses the 128.0.0.0/2 subnet for internal communications between the RE and PFEs. It was discovered that packets utilizing these IP addresses may egress an QFX5000 Series switch, leaking configuration information such as heartbeats, kernel versions, etc. out to the Internet, leading to an information exposure vulnerability. This issue affects Juniper Networks Junos OS on QFX5110, QFX5120, QFX5200, QFX5210 Series, and QFX5100 with QFX 5e Series image installed: All versions prior to 17.3R3-S12; 18.1 versions prior to 18.1R3-S13; 18.3 versions prior to 18.3R3-S5; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2; | ||||
| CVE-2021-31361 | 1 Juniper | 44 Junos, Ptx1000, Ptx1000-72q and 41 more | 2024-09-17 | 5.3 Medium |
| An Improper Check for Unusual or Exceptional Conditions vulnerability combined with Improper Handling of Exceptional Conditions in Juniper Networks Junos OS on QFX Series and PTX Series allows an unauthenticated network based attacker to cause increased FPC CPU utilization by sending specific IP packets which are being VXLAN encapsulated leading to a partial Denial of Service (DoS). Continued receipted of these specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX Series: All versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS on PTX Series: All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2. | ||||
| CVE-2019-0001 | 2 Fedoraproject, Juniper | 2 Fedora, Junos | 2024-09-17 | 7.5 High |
| Receipt of a malformed packet on MX Series devices with dynamic vlan configuration can trigger an uncontrolled recursion loop in the Broadband Edge subscriber management daemon (bbe-smgd), and lead to high CPU usage and a crash of the bbe-smgd service. Repeated receipt of the same packet can result in an extended denial of service condition for the device. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S1; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S1; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2. | ||||
| CVE-2018-0058 | 1 Juniper | 1 Junos | 2024-09-17 | N/A |
| Receipt of a specially crafted IPv6 exception packet may be able to trigger a kernel crash (vmcore), causing the device to reboot. The issue is specific to the processing of Broadband Edge (BBE) client route processing on MX Series subscriber management platforms, introduced by the Tomcat (Next Generation Subscriber Management) functionality in Junos OS 15.1. This issue affects no other platforms or configurations. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S2, 15.1R8 on MX Series; 16.1 versions prior to 16.1R4-S11, 16.1R7-S2, 16.1R8 on MX Series; 16.2 versions prior to 16.2R3 on MX Series; 17.1 versions prior to 17.1R2-S9, 17.1R3 on MX Series; 17.2 versions prior to 17.2R2-S6, 17.2R3 on MX Series; 17.3 versions prior to 17.3R2-S4, 17.3R3-S2, 17.3R4 on MX Series; 17.4 versions prior to 17.4R2 on MX Series; 18.1 versions prior to 18.1R2-S3, 18.1R3 on MX Series; 18.2 versions prior to 18.2R1-S1, 18.2R2 on MX Series. | ||||
| CVE-2019-0074 | 1 Juniper | 6 Ex9200, Junos, Nfx150 and 3 more | 2024-09-17 | 5.5 Medium |
| A path traversal vulnerability in NFX150 Series and QFX10K Series, EX9200 Series, MX Series and PTX Series devices with Next-Generation Routing Engine (NG-RE) allows a local authenticated user to read sensitive system files. This issue only affects NFX150 Series and QFX10K Series, EX9200 Series, MX Series and PTX Series with Next-Generation Routing Engine (NG-RE) which uses vmhost. This issue affects Juniper Networks Junos OS on NFX150 Series and QFX10K, EX9200 Series, MX Series and PTX Series with NG-RE and vmhost: 15.1F versions prior to 15.1F6-S12 16.1 versions starting from 16.1R6 and later releases, including the Service Releases, prior to 16.1R6-S6, 16.1R7-S3; 17.1 versions prior to 17.1R3; 17.2 versions starting from 17.2R1-S3, 17.2R3 and later releases, including the Service Releases, prior to 17.2R3-S1; 17.3 versions starting from 17.3R1-S1, 17.3R2 and later releases, including the Service Releases, prior to 17.3R3-S3; 17.4 versions starting from 17.4R1 and later releases, including the Service Releases, prior to 17.4R1-S6, 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S3; 18.2 versions prior to 18.2R2; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S2, 18.3R2; 18.4 versions prior to 18.4R1-S1, 18.4R2. This issue does not affect: Juniper Networks Junos OS 15.1 and 16.2. | ||||
| CVE-2021-0278 | 1 Juniper | 1 Junos | 2024-09-17 | 8.8 High |
| An Improper Input Validation vulnerability in J-Web of Juniper Networks Junos OS allows a locally authenticated attacker to escalate their privileges to root over the target device. junos:18.3R3-S5 junos:18.4R3-S9 junos:19.1R3-S6 junos:19.3R2-S6 junos:19.3R3-S3 junos:19.4R1-S4 junos:19.4R3-S4 junos:20.1R2-S2 junos:20.1R3 junos:20.2R3-S1 junos:20.3X75-D20 junos:20.3X75-D30 junos:20.4R2-S1 junos:20.4R3 junos:21.1R1-S1 junos:21.1R2 junos:21.2R1 junos:21.3R1 This issue affects: Juniper Networks Junos OS 19.3 versions 19.3R1 and above prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.3R1. | ||||
| CVE-2020-1646 | 1 Juniper | 2 Junos, Junos Os Evolved | 2024-09-17 | 7.5 High |
| On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific UPDATE for an EBGP peer can lead to a routing process daemon (RPD) crash and restart. This issue occurs only when the device is receiving and processing the BGP UPDATE for an EBGP peer. This issue does not occur when the device is receiving and processing the BGP UPDATE for an IBGP peer. However, the offending BGP UPDATE can originally come from an EBGP peer, propagates through the network via IBGP peers without causing crash, then it causes RPD crash when it is processed for a BGP UPDATE towards an EBGP peer. Repeated receipt and processing of the same specific BGP UPDATE can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 17.3R3-S6, 17.4R2-S7, and 18.1R3-S7. Juniper Networks Junos OS Evolved 19.2R2-EVO and later versions, prior to 19.3R1-EVO. Other Junos OS releases are not affected. | ||||
| CVE-2021-0231 | 1 Juniper | 15 Junos, Srx1500, Srx300 and 12 more | 2024-09-17 | 6.5 Medium |
| A path traversal vulnerability in the Juniper Networks SRX and vSRX Series may allow an authenticated J-web user to read sensitive system files. This issue affects Juniper Networks Junos OS on SRX and vSRX Series: 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3; 20.1 versions prior to 20.1R1-S4, 20.1R2; 20.2 versions prior to 20.2R1-S3, 20.2R2; This issue does not affect Juniper Networks Junos OS versions prior to 19.3R1. | ||||
| CVE-2021-0283 | 1 Juniper | 1 Junos | 2024-09-17 | 7.5 High |
| A buffer overflow vulnerability in the TCP/IP stack of Juniper Networks Junos OS allows an attacker to send specific sequences of packets to the device thereby causing a Denial of Service (DoS). By repeatedly sending these sequences of packets to the device, an attacker can sustain the Denial of Service (DoS) condition. The device will abnormally shut down as a result of these sent packets. A potential indicator of compromise will be the following message in the log files: "eventd[13955]: SYSTEM_ABNORMAL_SHUTDOWN: System abnormally shut down" These issue are only triggered by traffic destined to the device. Transit traffic will not trigger these issues. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S19; 15.1 versions prior to 15.1R7-S10; 16.1 version 16.1R1 and later versions; 16.2 version 16.2R1 and later versions; 17.1 version 17.1R1 and later versions; 17.2 version 17.2R1 and later versions; 17.3 versions prior to 17.3R3-S12; 17.4 version 17.4R1 and later versions; 18.1 versions prior to 18.1R3-S13; 18.2 version 18.2R1 and later versions; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2; 21.2 versions prior to 21.2R1-S1, 21.2R2. | ||||
| CVE-2020-1661 | 1 Juniper | 32 Ex2300, Ex2300-c, Ex3400 and 29 more | 2024-09-17 | 5.3 Medium |
| On Juniper Networks Junos OS devices configured as a DHCP forwarder, the Juniper Networks Dynamic Host Configuration Protocol Daemon (jdhcp) process might crash when receiving a malformed DHCP packet. This issue only affects devices configured as DHCP forwarder with forward-only option, that forward specified DHCP client packets, without creating a new subscriber session. The jdhcpd daemon automatically restarts without intervention, but continuous receipt of the malformed DHCP packet will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue can be triggered only by DHCPv4, it cannot be triggered by DHCPv6. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S16; 12.3X48 versions prior to 12.3X48-D105 on SRX Series; 14.1X53 versions prior to 14.1X53-D60 on EX and QFX Series; 15.1 versions prior to 15.1R7-S7; 15.1X49 versions prior to 15.1X49-D221, 15.1X49-D230 on SRX Series; 15.1X53 versions prior to 15.1X53-D593 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S5. | ||||
| CVE-2022-22220 | 1 Juniper | 2 Junos, Junos Os Evolved | 2024-09-17 | 5.9 Medium |
| A Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability in Routing Protocol Daemon (rpd) of Juniper Networks Junos OS, Junos OS Evolved allows a network-based unauthenticated attacker to cause a Denial of Service (DoS). When a BGP flow route with redirect IP extended community is received, and the reachability to the next-hop of the corresponding redirect IP is flapping, the rpd process might crash. Whether the crash occurs depends on the timing of the internally processing of these two events and is outside the attackers control. Please note that this issue also affects Route-Reflectors unless 'routing-options flow firewall-install-disable' is configured. This issue affects: Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S10, 18.4R3-S10; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.4 versions prior to 19.4R3-S8; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos OS Evolved: All versions prior to 20.4R2-EVO; 21.1-EVO versions prior to 21.1R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 18.4R1. | ||||
| CVE-2021-0242 | 1 Juniper | 2 Ex4300, Junos | 2024-09-17 | 6.5 Medium |
| A vulnerability due to the improper handling of direct memory access (DMA) buffers on EX4300 switches on Juniper Networks Junos OS allows an attacker sending specific unicast frames to trigger a Denial of Service (DoS) condition by exhausting DMA buffers, causing the FPC to crash and the device to restart. The DMA buffer leak is seen when receiving these specific, valid unicast frames on an interface without Layer 2 Protocol Tunneling (L2PT) or dot1x configured. Interfaces with either L2PT or dot1x configured are not vulnerable to this issue. When this issue occurs, DMA buffer usage keeps increasing and the following error log messages may be observed: Apr 14 14:29:34.360 /kernel: pid 64476 (pfex_junos), uid 0: exited on signal 11 (core dumped) Apr 14 14:29:33.790 init: pfe-manager (PID 64476) terminated by signal number 11. Core dumped! The DMA buffers on the FPC can be monitored by the executing vty command 'show heap': ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 4a46000 268435456 238230496 30204960 11 Kernel 1 18a46000 67108864 17618536 49490328 73 Bcm_sdk 2 23737000 117440512 18414552 99025960 84 DMA buf <<<<< keeps increasing 3 2a737000 16777216 16777216 0 0 DMA desc This issue affects Juniper Networks Junos OS on the EX4300: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. | ||||
| CVE-2020-1629 | 1 Juniper | 1 Junos | 2024-09-17 | 5.9 Medium |
| A race condition vulnerability on Juniper Network Junos OS devices may cause the routing protocol daemon (RPD) process to crash and restart while processing a BGP NOTIFICATION message. This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.2 version 17.2R2 and later versions; 17.2X75 versions prior to 17.2X75-D105, 17.2X75-D110; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S7, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3-S3; 18.2X75 versions prior to 18.2X75-D410, 18.2X75-D420, 18.2X75-D50, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S2, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S2, 19.1R2; 19.2 versions prior to 19.2R1-S4, 19.2R2. This issue does not affect Juniper Networks Junos OS prior to version 16.1R1. | ||||
| CVE-2022-22232 | 1 Juniper | 29 Junos, Srx100, Srx110 and 26 more | 2024-09-17 | 7.5 High |
| A NULL Pointer Dereference vulnerability in the Packet Forwarding Engine of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On SRX Series If Unified Threat Management (UTM) Enhanced Content Filtering (CF) is enabled and specific transit traffic is processed the PFE will crash and restart. This issue affects Juniper Networks Junos OS: 21.4 versions prior to 21.4R1-S2, 21.4R2 on SRX Series; 22.1 versions prior to 22.1R1-S1, 22.1R2 on SRX Series. This issue does not affect Juniper Networks Junos OS versions prior to 21.4R1. | ||||
| CVE-2020-1684 | 1 Juniper | 1 Junos | 2024-09-17 | 7.5 High |
| On Juniper Networks SRX Series configured with application identification inspection enabled, receipt of specific HTTP traffic can cause high CPU load utilization, which could lead to traffic interruption. Application identification is enabled by default and is automatically turned on when Intrusion Detection and Prevention (IDP), AppFW, AppQoS, or AppTrack is configured. Thus, this issue might occur when IDP, AppFW, AppQoS, or AppTrack is configured. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D105; 15.1X49 versions prior to 15.1X49-D221, 15.1X49-D230; 17.4 versions prior to 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S5, 18.4R3-S1; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2. | ||||
| CVE-2021-0266 | 1 Juniper | 2 Csrx, Junos | 2024-09-17 | 8.1 High |
| The use of multiple hard-coded cryptographic keys in cSRX Series software in Juniper Networks Junos OS allows an attacker to take control of any instance of a cSRX deployment through device management services. This issue affects: Juniper Networks Junos OS on cSRX Series: All versions prior to 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2. | ||||
| CVE-2019-0061 | 1 Juniper | 1 Junos | 2024-09-17 | 7.8 High |
| The management daemon (MGD) is responsible for all configuration and management operations in Junos OS. The Junos CLI communicates with MGD over an internal unix-domain socket and is granted special permission to open this protected mode socket. Due to a misconfiguration of the internal socket, a local, authenticated user may be able to exploit this vulnerability to gain administrative privileges. This issue only affects Linux-based platforms. FreeBSD-based platforms are unaffected by this vulnerability. Exploitation of this vulnerability requires Junos shell access. This issue cannot be exploited from the Junos CLI. This issue affects Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D171, 15.1X49-D180; 15.1X53 versions prior to 15.1X53-D496, 15.1X53-D69; 16.1 versions prior to 16.1R7-S4; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R1-S8, 17.2R2-S7, 17.2R3-S1; 17.3 versions prior to 17.3R3-S4; 17.4 versions prior to 17.4R1-S6, 17.4R1-S7, 17.4R2-S3, 17.4R3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S4; 18.2 versions prior to 18.2R1-S5, 18.2R2-S2, 18.2R3; 18.3 versions prior to 18.3R1-S3, 18.3R2; 18.4 versions prior to 18.4R1-S2, 18.4R2. | ||||
| CVE-2019-0012 | 1 Juniper | 1 Junos | 2024-09-17 | 7.5 High |
| A Denial of Service (DoS) vulnerability in BGP in Juniper Networks Junos OS configured as a VPLS PE allows an attacker to craft a specific BGP message to cause the routing protocol daemon (rpd) process to crash and restart. While rpd restarts after a crash, repeated crashes can result in an extended DoS condition. This issue only affects PE routers configured with BGP Auto discovery for LDP VPLS. Other BGP configurations are unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D81; 12.3 versions prior to 12.3R12-S12; 12.3X48 versions prior to 12.3X48-D76; 14.1X53 versions prior to 14.1X53-D48; 15.1 versions prior to 15.1F6-S12, 15.1R7-S2; 15.1X49 versions prior to 15.1X49-D150; 15.1X53 versions prior to 15.1X53-D235, 15.1X53-D495, 15.1X53-D590, 15.1X53-D68; 16.1 versions prior to 16.1R3-S10, 16.1R4-S12, 16.1R6-S6, 16.1R7-S1; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S9, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R1-S5, 17.4R2; 18.1 versions prior to 18.1R2-S3, 18.1R3. | ||||
| CVE-2018-0053 | 1 Juniper | 2 Junos, Vsrx | 2024-09-17 | N/A |
| An authentication bypass vulnerability in the initial boot sequence of Juniper Networks Junos OS on vSRX Series may allow an attacker to gain full control of the system without authentication when the system is initially booted up. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D30 on vSRX. | ||||
| CVE-2021-0294 | 1 Juniper | 8 Ex4600, Ex4650, Junos and 5 more | 2024-09-17 | 5.3 Medium |
| A vulnerability in Juniper Networks Junos OS, which only affects the release 18.4R2-S5, where a function is inconsistently implemented on Juniper Networks Junos QFX5000 Series and EX4600 Series, and if "storm-control enhanced" is configured, can lead to the enhanced storm control filter group not be installed. It will cause storm control not to work hence allowing an attacker to cause high CPU usage or packet loss issues by sending a large amount of broadcast or unknown unicast packets arriving the device. This issue affects Juniper Networks QFX5100, QFX5110, QFX5120, QFX5200, QFX5210, EX4600, and EX4650, and QFX5100 with QFX 5e Series image installed. QFX5130 and QFX5220 are not affected from this issue. This issue affects Juniper Networks Junos OS 18.4R2-S5 on QFX5000 Series and EX4600 Series. No other product or platform is affected by this vulnerability. | ||||