Total
1815 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-26878 | 3 Debian, Linux, Redhat | 3 Debian Linux, Linux Kernel, Enterprise Linux | 2025-01-14 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: quota: Fix potential NULL pointer dereference Below race may cause NULL pointer dereference P1 P2 dquot_free_inode quota_off drop_dquot_ref remove_dquot_ref dquots = i_dquot(inode) dquots = i_dquot(inode) srcu_read_lock dquots[cnt]) != NULL (1) dquots[type] = NULL (2) spin_lock(&dquots[cnt]->dq_dqb_lock) (3) .... If dquot_free_inode(or other routines) checks inode's quota pointers (1) before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer dereference will be triggered. So let's fix it by using a temporary pointer to avoid this issue. | ||||
| CVE-2024-56441 | 1 Huawei | 2 Emui, Harmonyos | 2025-01-13 | 4.1 Medium |
| Race condition vulnerability in the Bastet module Impact: Successful exploitation of this vulnerability may affect service confidentiality. | ||||
| CVE-2024-54120 | 1 Huawei | 1 Harmonyos | 2025-01-13 | 4.1 Medium |
| Race condition vulnerability in the distributed notification module Impact: Successful exploitation of this vulnerability may cause features to perform abnormally. | ||||
| CVE-2023-52517 | 1 Linux | 1 Linux Kernel | 2025-01-13 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain Previously the transfer complete IRQ immediately drained to RX FIFO to read any data remaining in FIFO to the RX buffer. This behaviour is correct when dealing with SPI in interrupt mode. However in DMA mode the transfer complete interrupt still fires as soon as all bytes to be transferred have been stored in the FIFO. At that point data in the FIFO still needs to be picked up by the DMA engine. Thus the drain procedure and DMA engine end up racing to read from RX FIFO, corrupting any data read. Additionally the RX buffer pointer is never adjusted according to DMA progress in DMA mode, thus calling the RX FIFO drain procedure in DMA mode is a bug. Fix corruptions in DMA RX mode by draining RX FIFO only in interrupt mode. Also wait for completion of RX DMA when in DMA mode before returning to ensure all data has been copied to the supplied memory buffer. | ||||
| CVE-2023-52480 | 1 Linux | 1 Linux Kernel | 2025-01-13 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix race condition between session lookup and expire Thread A + Thread B ksmbd_session_lookup | smb2_sess_setup sess = xa_load | | | xa_erase(&conn->sessions, sess->id); | | ksmbd_session_destroy(sess) --> kfree(sess) | // UAF! | sess->last_active = jiffies | + This patch add rwsem to fix race condition between ksmbd_session_lookup and ksmbd_expire_session. | ||||
| CVE-2023-52478 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-01-10 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: HID: logitech-hidpp: Fix kernel crash on receiver USB disconnect hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU) races when it races with itself. hidpp_connect_event() primarily runs from a workqueue but it also runs on probe() and if a "device-connected" packet is received by the hw when the thread running hidpp_connect_event() from probe() is waiting on the hw, then a second thread running hidpp_connect_event() will be started from the workqueue. This opens the following races (note the below code is simplified): 1. Retrieving + printing the protocol (harmless race): if (!hidpp->protocol_major) { hidpp_root_get_protocol_version() hidpp->protocol_major = response.rap.params[0]; } We can actually see this race hit in the dmesg in the abrt output attached to rhbz#2227968: [ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected. [ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected. Testing with extra logging added has shown that after this the 2 threads take turn grabbing the hw access mutex (send_mutex) so they ping-pong through all the other TOCTOU cases managing to hit all of them: 2. Updating the name to the HIDPP name (harmless race): if (hidpp->name == hdev->name) { ... hidpp->name = new_name; } 3. Initializing the power_supply class for the battery (problematic!): hidpp_initialize_battery() { if (hidpp->battery.ps) return 0; probe_battery(); /* Blocks, threads take turns executing this */ hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); } 4. Creating delayed input_device (potentially problematic): if (hidpp->delayed_input) return; hidpp->delayed_input = hidpp_allocate_input(hdev); The really big problem here is 3. Hitting the race leads to the following sequence: hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); ... hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); So now we have registered 2 power supplies for the same battery, which looks a bit weird from userspace's pov but this is not even the really big problem. Notice how: 1. This is all devm-maganaged 2. The hidpp->battery.desc struct is shared between the 2 power supplies 3. hidpp->battery.desc.properties points to the result from the second devm_kmemdup() This causes a use after free scenario on USB disconnect of the receiver: 1. The last registered power supply class device gets unregistered 2. The memory from the last devm_kmemdup() call gets freed, hidpp->battery.desc.properties now points to freed memory 3. The first registered power supply class device gets unregistered, this involves sending a remove uevent to userspace which invokes power_supply_uevent() to fill the uevent data 4. power_supply_uevent() uses hidpp->battery.desc.properties which now points to freed memory leading to backtraces like this one: Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08 ... Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0 ... Sep 22 20:01:35 eric kernel: ? asm_exc_page_fault+0x26/0x30 Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0xee/0x1d0 Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0x10d/0x1d0 Sep 22 20:01:35 eric kernel: dev_uevent+0x10f/0x2d0 Sep 22 20:01:35 eric kernel: kobject_uevent_env+0x291/0x680 Sep 22 20:01:35 eric kernel: ---truncated--- | ||||
| CVE-2023-33974 | 1 Riot-os | 1 Riot | 2025-01-10 | 7.5 High |
| RIOT-OS, an operating system for Internet of Things (IoT) devices, contains a network stack with the ability to process 6LoWPAN frames. In versions 2023.01 and prior, an attacker can send multiple crafted frames to the device to trigger a race condition. The race condition invalidates assumptions about the program state and leads to an invalid memory access resulting in denial of service. This issue is patched in pull request 19679. There are no known workarounds. | ||||
| CVE-2021-47069 | 2 Linux, Redhat | 6 Linux Kernel, Enterprise Linux, Rhel Aus and 3 more | 2025-01-09 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: ipc/mqueue, msg, sem: avoid relying on a stack reference past its expiry do_mq_timedreceive calls wq_sleep with a stack local address. The sender (do_mq_timedsend) uses this address to later call pipelined_send. This leads to a very hard to trigger race where a do_mq_timedreceive call might return and leave do_mq_timedsend to rely on an invalid address, causing the following crash: RIP: 0010:wake_q_add_safe+0x13/0x60 Call Trace: __x64_sys_mq_timedsend+0x2a9/0x490 do_syscall_64+0x80/0x680 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f5928e40343 The race occurs as: 1. do_mq_timedreceive calls wq_sleep with the address of `struct ext_wait_queue` on function stack (aliased as `ewq_addr` here) - it holds a valid `struct ext_wait_queue *` as long as the stack has not been overwritten. 2. `ewq_addr` gets added to info->e_wait_q[RECV].list in wq_add, and do_mq_timedsend receives it via wq_get_first_waiter(info, RECV) to call __pipelined_op. 3. Sender calls __pipelined_op::smp_store_release(&this->state, STATE_READY). Here is where the race window begins. (`this` is `ewq_addr`.) 4. If the receiver wakes up now in do_mq_timedreceive::wq_sleep, it will see `state == STATE_READY` and break. 5. do_mq_timedreceive returns, and `ewq_addr` is no longer guaranteed to be a `struct ext_wait_queue *` since it was on do_mq_timedreceive's stack. (Although the address may not get overwritten until another function happens to touch it, which means it can persist around for an indefinite time.) 6. do_mq_timedsend::__pipelined_op() still believes `ewq_addr` is a `struct ext_wait_queue *`, and uses it to find a task_struct to pass to the wake_q_add_safe call. In the lucky case where nothing has overwritten `ewq_addr` yet, `ewq_addr->task` is the right task_struct. In the unlucky case, __pipelined_op::wake_q_add_safe gets handed a bogus address as the receiver's task_struct causing the crash. do_mq_timedsend::__pipelined_op() should not dereference `this` after setting STATE_READY, as the receiver counterpart is now free to return. Change __pipelined_op to call wake_q_add_safe on the receiver's task_struct returned by get_task_struct, instead of dereferencing `this` which sits on the receiver's stack. As Manfred pointed out, the race potentially also exists in ipc/msg.c::expunge_all and ipc/sem.c::wake_up_sem_queue_prepare. Fix those in the same way. | ||||
| CVE-2023-29537 | 1 Mozilla | 2 Firefox, Focus | 2025-01-09 | 7.5 High |
| Multiple race conditions in the font initialization could have led to memory corruption and execution of attacker-controlled code. This vulnerability affects Firefox for Android < 112, Firefox < 112, and Focus for Android < 112. | ||||
| CVE-2024-30046 | 2 Microsoft, Redhat | 3 .net, Visual Studio 2022, Enterprise Linux | 2025-01-08 | 5.9 Medium |
| Visual Studio Denial of Service Vulnerability | ||||
| CVE-2023-6109 | 1 Yop-poll | 1 Yop Poll | 2025-01-08 | 5.3 Medium |
| The YOP Poll plugin for WordPress is vulnerable to a race condition in all versions up to, and including, 6.5.26. This is due to improper restrictions on the add() function. This makes it possible for unauthenticated attackers to place multiple votes on a single poll even when the poll is set to one vote per person. | ||||
| CVE-2024-26243 | 1 Microsoft | 7 Windows 10 21h2, Windows 10 22h2, Windows 11 21h2 and 4 more | 2025-01-08 | 7 High |
| Windows USB Print Driver Elevation of Privilege Vulnerability | ||||
| CVE-2024-26242 | 1 Microsoft | 14 Windows 10 1507, Windows 10 1607, Windows 10 1809 and 11 more | 2025-01-08 | 7 High |
| Windows Telephony Server Elevation of Privilege Vulnerability | ||||
| CVE-2024-26236 | 1 Microsoft | 1 Windows Server 2022 23h2 | 2025-01-08 | 7 High |
| Windows Update Stack Elevation of Privilege Vulnerability | ||||
| CVE-2024-30031 | 1 Microsoft | 16 Windows, Windows 10 1507, Windows 10 1607 and 13 more | 2025-01-08 | 7.8 High |
| Windows CNG Key Isolation Service Elevation of Privilege Vulnerability | ||||
| CVE-2023-20736 | 3 Google, Linuxfoundation, Mediatek | 23 Android, Iot-yocto, Yocto and 20 more | 2025-01-07 | 6.4 Medium |
| In vcu, there is a possible out of bounds write due to a race condition. This could lead to local escalation of privilege with System execution privileges needed. User interaction is not needed for exploitation. Patch ID: ALPS07645149; Issue ID: ALPS07645189. | ||||
| CVE-2023-20750 | 2 Google, Mediatek | 23 Android, Mt6835, Mt6886 and 20 more | 2025-01-07 | 4.1 Medium |
| In swpm, there is a possible out of bounds write due to a race condition. This could lead to local information disclosure with System execution privileges needed. User interaction is not needed for exploitation. Patch ID: ALPS07780926; Issue ID: ALPS07780928. | ||||
| CVE-2023-52749 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-01-06 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: spi: Fix null dereference on suspend A race condition exists where a synchronous (noqueue) transfer can be active during a system suspend. This can cause a null pointer dereference exception to occur when the system resumes. Example order of events leading to the exception: 1. spi_sync() calls __spi_transfer_message_noqueue() which sets ctlr->cur_msg 2. Spi transfer begins via spi_transfer_one_message() 3. System is suspended interrupting the transfer context 4. System is resumed 6. spi_controller_resume() calls spi_start_queue() which resets cur_msg to NULL 7. Spi transfer context resumes and spi_finalize_current_message() is called which dereferences cur_msg (which is now NULL) Wait for synchronous transfers to complete before suspending by acquiring the bus mutex and setting/checking a suspend flag. | ||||
| CVE-2024-56664 | 1 Linux | 1 Linux Kernel | 2025-01-06 | 7.0 High |
| In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Fix race between element replace and close() Element replace (with a socket different from the one stored) may race with socket's close() link popping & unlinking. __sock_map_delete() unconditionally unrefs the (wrong) element: // set map[0] = s0 map_update_elem(map, 0, s0) // drop fd of s0 close(s0) sock_map_close() lock_sock(sk) (s0!) sock_map_remove_links(sk) link = sk_psock_link_pop() sock_map_unlink(sk, link) sock_map_delete_from_link // replace map[0] with s1 map_update_elem(map, 0, s1) sock_map_update_elem (s1!) lock_sock(sk) sock_map_update_common psock = sk_psock(sk) spin_lock(&stab->lock) osk = stab->sks[idx] sock_map_add_link(..., &stab->sks[idx]) sock_map_unref(osk, &stab->sks[idx]) psock = sk_psock(osk) sk_psock_put(sk, psock) if (refcount_dec_and_test(&psock)) sk_psock_drop(sk, psock) spin_unlock(&stab->lock) unlock_sock(sk) __sock_map_delete spin_lock(&stab->lock) sk = *psk // s1 replaced s0; sk == s1 if (!sk_test || sk_test == sk) // sk_test (s0) != sk (s1); no branch sk = xchg(psk, NULL) if (sk) sock_map_unref(sk, psk) // unref s1; sks[idx] will dangle psock = sk_psock(sk) sk_psock_put(sk, psock) if (refcount_dec_and_test()) sk_psock_drop(sk, psock) spin_unlock(&stab->lock) release_sock(sk) Then close(map) enqueues bpf_map_free_deferred, which finally calls sock_map_free(). This results in some refcount_t warnings along with a KASAN splat [1]. Fix __sock_map_delete(), do not allow sock_map_unref() on elements that may have been replaced. [1]: BUG: KASAN: slab-use-after-free in sock_map_free+0x10e/0x330 Write of size 4 at addr ffff88811f5b9100 by task kworker/u64:12/1063 CPU: 14 UID: 0 PID: 1063 Comm: kworker/u64:12 Not tainted 6.12.0+ #125 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014 Workqueue: events_unbound bpf_map_free_deferred Call Trace: <TASK> dump_stack_lvl+0x68/0x90 print_report+0x174/0x4f6 kasan_report+0xb9/0x190 kasan_check_range+0x10f/0x1e0 sock_map_free+0x10e/0x330 bpf_map_free_deferred+0x173/0x320 process_one_work+0x846/0x1420 worker_thread+0x5b3/0xf80 kthread+0x29e/0x360 ret_from_fork+0x2d/0x70 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 1202: kasan_save_stack+0x1e/0x40 kasan_save_track+0x10/0x30 __kasan_slab_alloc+0x85/0x90 kmem_cache_alloc_noprof+0x131/0x450 sk_prot_alloc+0x5b/0x220 sk_alloc+0x2c/0x870 unix_create1+0x88/0x8a0 unix_create+0xc5/0x180 __sock_create+0x241/0x650 __sys_socketpair+0x1ce/0x420 __x64_sys_socketpair+0x92/0x100 do_syscall_64+0x93/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e Freed by task 46: kasan_save_stack+0x1e/0x40 kasan_save_track+0x10/0x30 kasan_save_free_info+0x37/0x60 __kasan_slab_free+0x4b/0x70 kmem_cache_free+0x1a1/0x590 __sk_destruct+0x388/0x5a0 sk_psock_destroy+0x73e/0xa50 process_one_work+0x846/0x1420 worker_thread+0x5b3/0xf80 kthread+0x29e/0x360 ret_from_fork+0x2d/0x70 ret_from_fork_asm+0x1a/0x30 The bu ---truncated--- | ||||
| CVE-2022-41035 | 1 Microsoft | 1 Edge Chromium | 2025-01-02 | 5.3 Medium |
| Microsoft Edge (Chromium-based) Spoofing Vulnerability | ||||