| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
rtc: ac100: Fix clock provider use-after-free on probe failure
ac100_rtc_register_clks() registers the RTC-32k clock with
clk_hw_register_fixed_rate() and the clock provider with
of_clk_add_hw_provider(). Neither is device managed, and both are
released only from ac100_rtc_remove(). The driver core does not call
remove() when probe() fails: really_probe() reaches probe_failed below
the device_remove() call and goes straight to releasing the device's
managed resources.
ac100_rtc_probe() ends with
return devm_rtc_register_device(chip->rtc);
so if that fails after the clocks have been registered, the provider is
left on the global of_clk_providers list holding chip->clk_data, which
was allocated with devm_kzalloc() and is freed while probe() unwinds. A
later lookup on this device tree node then reads freed memory in
of_clk_hw_onecell_get(). Consumers that do exactly that exist in tree:
the wifi power sequence nodes on sun8i-a83t-bananapi-m3 and
sun8i-a83t-cubietruck-plus take <&ac100_rtc 1>, and the sun9i-a80 boards
route osc32k through <&ac100_rtc 0>. The window is narrow, as
devm_rtc_register_device() can only fail with -ENOMEM here, but the
provider is left dangling whenever it does.
The RTC-32k clock is leaked on the same path. Since clk_core_lookup()
searches a global list that is not scoped per device, __clk_register()
rejects the duplicate name with -EEXIST, so the leak also makes a later
probe of the same device fail.
The error path that returns -EINVAL when the ADDA 4M parent clock cannot
be found leaks the RTC-32k clock in the same way. No provider has been
registered at that point, so that one is a leak rather than a
use-after-free.
Register both with devm_clk_hw_register_fixed_rate() and
devm_of_clk_add_hw_provider() so that they are released whenever the
device goes away, on a failed probe as well as on unbind. Devres
releases in reverse order of acquisition, so the provider is removed
before chip->clk_data is freed, and the clkout children are now
unregistered before their parent rather than after it.
ac100_rtc_unregister_clks() and the remove callback then have nothing
left to do and are removed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: reject short WMI command responses
ath9k_wmi_rsp_callback() removes the validated WMI header and copies
the number of bytes expected by the waiting command into its response
buffer. A device response shorter than that expectation can therefore
be read beyond the skb payload.
Record -EMSGSIZE for a short response, complete the waiter, and return
the stored status from the command path. This also prevents callers from
consuming stale response bytes as a successful reply. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wfx: validate MIB read length before copying to caller
wfx_hif_read_mib() copies reply->length bytes from the firmware
response into the caller-provided buffer without checking that
reply->length does not exceed val_len. A firmware response with
a length field larger than expected overruns the caller buffer and
reads past the end of the reply allocation.
Replace the dead -ENOMEM check with an active validation that
reply->length fits within val_len before the memcpy. |
| Double free in Microsoft Office Excel allows an unauthorized attacker to execute code over a network. |
| Out-of-bounds read in Windows Partition Management Driver allows an unauthorized attacker to execute code over a network. |
| Use after free in Windows Broadcast DVR User Service allows an authorized attacker to elevate privileges locally. |
| During an upload, curl mishandles HTTP/2 `RST_STREAM` received from the server
(with reason `HTTP_1_1_REQUIRED` or `REFUSED_STREAM`) leading to a use after
free of a `struct Curl_easy` object. |
| An issue was discovered in HAProxy before 3.3.6. The HTTP/3 parser does not check that the received body length matches a previously announced content-length when the stream is closed via a frame with an empty payload. This can cause desynchronization issues with the backend server and could be used for request smuggling. The earliest affected version is 2.6. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Fix inquiry cache use-after-free
The sync command worker holds hdev->req_lock, but inquiry-cache updates
and flushes use hdev->lock. Both hci_acl_create_conn_sync() and
hci_stop_discovery_sync() look up entries and read their fields without
taking hdev->lock.
After either lookup returns, a concurrent HCIINQUIRY ioctl can acquire
hdev->lock and flush the cache, freeing the entry. The worker then reads
the freed entry while preparing a create-connection or remote-name-cancel
command. The list traversal also races with cache updates and removal.
KASAN reported these accesses:
BUG: KASAN: slab-use-after-free in hci_acl_create_conn_sync+0x5f1/0x650
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_acl_create_conn_sync+0x5f1/0x650
hci_cmd_sync_work+0x13c/0x290
Allocated by task 90:
hci_inquiry_cache_update+0x3e6/0x7d0
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 93:
hci_inquiry_cache_flush+0x111/0x2b0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
BUG: KASAN: slab-use-after-free in hci_stop_discovery_sync+0x3b1/0x3c0
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_stop_discovery_sync+0x3b1/0x3c0
hci_cmd_sync_work+0x173/0x300
Allocated by task 86:
hci_inquiry_cache_update+0x483/0x940
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 91:
hci_inquiry_cache_flush+0x13e/0x2f0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
Hold hdev->lock across each lookup and all reads from its result. Copy the
remote address before unlocking so discovery cancellation does not retain
a cache entry pointer. Release the lock before sending synchronous HCI
commands, since their completion handlers may need the same lock. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: Fix initial port reference race
For RFCOMM_RELEASE_ONHUP devices, rfcomm_tty_install() and
__rfcomm_release_dev() both use RFCOMM_TTY_OWNED to decide who drops the
initial tty_port reference. The release path tests the bit separately
from the install path setting it, so both can drop that reference.
The synchronous hangup does not prevent this race: port->tty is not
assigned until tty_port_open(), after installation. The following
interleaving is possible:
1. Install and release each obtain a reference with rfcomm_dev_get().
2. Release observes RFCOMM_TTY_OWNED clear.
3. Install sets RFCOMM_TTY_OWNED and drops the initial reference.
4. Release drops the same initial reference again.
5. TTY cleanup drops its reference and frees the device.
6. Release performs its final tty_port_put() on the freed port.
KASAN reported:
BUG: KASAN: slab-use-after-free in tty_port_put+0x22/0x190
Write of size 4 at addr ffff8881001d3d5c by task poc/92
Call Trace:
tty_port_put+0x22/0x190
rfcomm_dev_ioctl+0x1d4/0x1930
sock_do_ioctl+0x110/0x260
sock_ioctl+0x380/0x590
__x64_sys_ioctl+0x134/0x1c0
Allocated by task 88:
rfcomm_dev_ioctl+0x8f6/0x1930
sock_do_ioctl+0x110/0x260
sock_ioctl+0x380/0x590
__x64_sys_ioctl+0x134/0x1c0
Freed by task 65:
kfree+0x131/0x3c0
rfcomm_dev_destruct+0x23b/0x2f0
release_one_tty+0xc1/0x370
process_one_work+0x661/0x1090
Use test_and_set_bit() in both paths so that only the caller that changes
RFCOMM_TTY_OWNED from clear to set drops the initial reference. Each path
keeps its own lookup reference until release or TTY cleanup, preserving
the existing callback ordering and error handling. |
| In the Linux kernel, the following vulnerability has been resolved:
EDAC/altera: Drop __init from ECC setup paths for re-probe safety
Sashiko reports:
"Does suppressing sysfs unbinding fully prevent the execution of freed __init
memory? If altr_sysmgr_regmap_lookup_by_phandle() returns -EPROBE_DEFER, the
probe is deferred until after __init memory is freed."
The a10 EDAC .setup callbacks (sdmmc, ethernet, nand, dma, usb, qspi) and
their helpers (altr_init_a10_ecc_device_type, altr_init_a10_ecc_block) were
marked __init. These run from the probe path, which may execute after init
memory is freed -- e.g. a probe deferred via -EPROBE_DEFER that only succeeds
once a late/module dependency appears, or a manual unbind/rebind. Calling
__init code then dereferences freed memory. Remove __init so these functions
remain valid at runtime. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: ua101: reject mismatched capture/playback packet sizes
detect_usb_format() cross-checks bSubframeSize, bBitResolution and
tSamFreq between the capture and playback interfaces, but never relates
the two endpoints' wMaxPacketSize and bNrChannels. Each playback URB
gets a buffer of ua->playback.max_packet_bytes, while the number of
bytes written into it is derived from the capture stream:
capture_urb_complete() computes frames from the received capture packet
and capture.frame_bytes, and start_usb_playback() and playback_work()
multiply that by playback.frame_bytes.
A device declaring a large capture wMaxPacketSize with few capture
channels and a small playback wMaxPacketSize with many playback channels
therefore memset()s and memcpy()s past the end of the playback buffer,
in open() of the PCM node the driver registers during probe.
usb_submit_urb() rejects the over-long iso_frame_desc[0].length with
-EMSGSIZE, but only after the write.
Reject such descriptors at probe time. Genuine UA-101/UA-1000 hardware
declares proportional packet sizes and is unaffected.
BUG: KASAN: slab-out-of-bounds in start_usb_playback (sound/usb/misc/ua101.c:586)
Write of size 2048 at addr ffff8881098f3c00 by task exploit/5021
Call Trace:
__asan_memset (mm/kasan/shadow.c:84)
start_usb_playback (sound/usb/misc/ua101.c:586)
playback_pcm_open (sound/usb/misc/ua101.c:679)
snd_pcm_open_substream (sound/core/pcm_native.c:2829)
snd_pcm_open (sound/core/pcm_native.c:2865 sound/core/pcm_native.c:2932)
snd_pcm_playback_open (sound/core/pcm_native.c:2891)
snd_open (sound/core/sound.c:166)
chrdev_open (fs/char_dev.c:411)
do_dentry_open (fs/open.c:996)
vfs_open (fs/open.c:1101)
path_openat (fs/namei.c:4837 fs/namei.c:5000)
do_file_open (fs/namei.c:5029)
do_sys_openat2 (fs/open.c:1417)
__x64_sys_openat (fs/open.c:1423 fs/open.c:1439 fs/open.c:1434)
do_syscall_64 (arch/x86/entry/syscall_64.c:61 arch/x86/entry/syscall_64.c:84)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
The buggy address belongs to the object at ffff8881098f3c00
which belongs to the cache kmalloc-192 of size 192
The buggy address is located 0 bytes inside of
allocated 168-byte region [ffff8881098f3c00, ffff8881098f3ca8) |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: rt1017-sdca-sdw: fix uninitialized stream_config->type
stream_config is not initialized before being passed to
sdw_stream_add_slave(). The type field may contain garbage and is
later copied to stream->type by sdw_config_stream().
Zero-initialize stream_config so type defaults to SDW_STREAM_PCM.
While at it, use snd_sdw_params_to_config() helper instead of
open-coding the same logic. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: max3100: shut down timer before freeing port
max3100_shutdown() stops the polling timer but returns early during
system suspend. If the SPI device is unbound before resume, the serial
core does not call max3100_shutdown() again, so max3100_remove() frees
the port while the timer remains armed. max3100_timeout() may then
access the freed port and re-arm the timer.
Add final timer teardown to max3100_remove() and use
timer_shutdown_sync() to prevent a racing callback from re-arming it.
Also free the IRQ and destroy the workqueue there before freeing the
port. Keep timer_delete_sync() in max3100_shutdown() so that a
subsequent open() can re-arm the timer.
The workqueue is created before request_irq() and destroyed on both
request_irq() failure and normal shutdown. Its presence at remove thus
identifies the IRQ left registered when suspend bypasses shutdown.
Free the IRQ before destroying the workqueue, in both
max3100_shutdown() and max3100_remove(), and cancel the pending work
in between. free_irq() waits for a running interrupt handler to
finish and no new handler can start afterwards, so a racing handler
cannot queue work on a workqueue that is being destroyed; the
force_end_work check in max3100_dowork() only narrows that window, as
a handler delayed between the check and queue_work() could still run
after the teardown has cleared the workqueue pointer. Cancelling the
work also keeps destroy_workqueue() from waiting on a queued work item
in case remove() ever runs while the freezable workqueue is still
frozen, e.g. device removal during the resume window, before
workqueues are thawed.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
of/overlay: don't leak fragment references when changeset init fails
init_overlay_changeset() stores the number of initialized fragments
in ovcs->count only on full success. When find_target() or the
__symbols__ lookup fails partway through, the target and overlay
references taken for the fragments initialized so far are never
dropped: free_overlay_changeset() bounds its cleanup loop by
ovcs->count, which is still 0.
Store the running count on the error path so free_overlay_changeset()
puts whatever was set up. The store is guarded by ovcs->fragments
because on the allocation-failure path cnt still holds the counting
pass total while there is no fragments array; everywhere else cnt
only counts fully-initialized fragments. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: save IRQ state in blkg_tryget_closest()
bio_set_dev() associates the bio with a blkg through bio_associate_blkg().
If the blkg lookup misses, blkg_tryget_closest() takes q->queue_lock with
spin_lock_irq() and releases it with spin_unlock_irq(), which
unconditionally enables local interrupts.
Callers may call bio_set_dev() with interrupts already disabled, e.g.
dm-thin's pool_map() does so while holding pool->lock taken with
spin_lock_irq(). The nested spin_unlock_irq() then enables interrupts
while pool->lock is still held, so an I/O completion softirq can run on
the same CPU, re-acquire pool->lock (thin_endio(), or overwrite_endio()
-> complete_mapping_preparation()) and deadlock. lockdep reports this
as inconsistent SOFTIRQ-ON-W to IN-SOFTIRQ-W usage.
Commit 3a762de55b4e ("block: save irq state in blkg_lookup_create()")
fixed the same problem while the lock lived in blkg_lookup_create(), but
commit 9327a865e395 ("blk-cgroup: don't nest queue_lock under rcu in
blkg_lookup_create()") moved the locking into blkg_tryget_closest() and
reverted it to spin_lock_irq().
Save and restore the caller's IRQ state instead. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: core: call _get_device() with the master MTD
__get_mtd_device() calls the master's _get_device() callback with mtd,
which may be a partition. __put_mtd_device() passes the master.
This breaks gluebi partitions because gluebi_get_device() uses
container_of() and therefore requires the master MTD. Pass the master
to _get_device(), matching _put_device(). |
| Heap-based buffer overflow in Windows Container Isolation FS Filter Driver (unionfs.sys) allows an authorized attacker to elevate privileges locally. |
| Heap-based buffer overflow in Windows Hyper-V allows an authorized attacker to disclose information over a network. |
| Photoshop Desktop is affected by an Incorrect Authorization vulnerability that could result in arbitrary code execution in the context of the current user. An attacker could exploit this vulnerability to execute arbitrary code. Exploitation of this issue requires user interaction in that a victim must open a malicious file. Scope is changed. |
