Filtered by vendor Juniper
Subscriptions
Filtered by product Ex4650
Subscriptions
Total
39 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2023-44191 | 2 Juniper, Juniper Networks | 26 Ex2300, Ex2300-c, Ex2300 Multigigabit and 23 more | 2024-09-19 | 7.5 High |
| An Allocation of Resources Without Limits or Throttling vulnerability in Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On all Junos OS QFX5000 Series and EX4000 Series platforms, when a high number of VLANs are configured, a specific DHCP packet will cause PFE hogging which will lead to dropping of socket connections. This issue affects: Juniper Networks Junos OS on QFX5000 Series and EX4000 Series * 21.1 versions prior to 21.1R3-S5; * 21.2 versions prior to 21.2R3-S5; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S3; * 22.2 versions prior to 22.2R3-S1; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1 | ||||
| CVE-2023-44183 | 1 Juniper | 11 Ex4600, Ex4650, Junos and 8 more | 2024-09-18 | 6.5 Medium |
| An Improper Input Validation vulnerability in the VxLAN packet forwarding engine (PFE) of Juniper Networks Junos OS on QFX5000 Series, EX4600 Series devices allows an unauthenticated, adjacent attacker, sending two or more genuine packets in the same VxLAN topology to possibly cause a DMA memory leak to occur under various specific operational conditions. The scenario described here is the worst-case scenario. There are other scenarios that require operator action to occur. An indicator of compromise may be seen when multiple devices indicate that FPC0 has gone missing when issuing a show chassis fpc command for about 10 to 20 minutes, and a number of interfaces have also gone missing. Use the following command to determine if FPC0 has gone missing from the device. show chassis fpc detail This issue affects: Juniper Networks Junos OS on QFX5000 Series, EX4600 Series: * 18.4 version 18.4R2 and later versions prior to 20.4R3-S8; * 21.1 version 21.1R1 and later versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S3; * 22.2 versions prior to 22.2R3-S1; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2. | ||||
| CVE-2022-22226 | 1 Juniper | 35 Ex4300, Ex4300-24p, Ex4300-24p-s and 32 more | 2024-09-17 | 6.5 Medium |
| In VxLAN scenarios on EX4300-MP, EX4600, QFX5000 Series devices an Uncontrolled Memory Allocation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated adjacently located attacker sending specific packets to cause a Denial of Service (DoS) condition by crashing one or more PFE's when they are received and processed by the device. Upon automatic restart of the PFE, continued processing of these packets will cause the memory leak to reappear. Depending on the volume of packets received the attacker may be able to create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP, EX4600, QFX5000 Series: 17.1 version 17.1R1 and later versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S7, 19.2R3-S1; 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Junos OS versions prior to 17.1R1. | ||||
| CVE-2021-0289 | 1 Juniper | 229 Acx1000, Acx1100, Acx2000 and 226 more | 2024-09-17 | 6.5 Medium |
| When user-defined ARP Policer is configured and applied on one or more Aggregated Ethernet (AE) interface units, a Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability between the Device Control Daemon (DCD) and firewall process (dfwd) daemons of Juniper Networks Junos OS allows an attacker to bypass the user-defined ARP Policer. In this particular case the User ARP policer is replaced with default ARP policer. To review the desired ARP Policers and actual state one can run the command "show interfaces <> extensive" and review the output. See further details below. An example output is: show interfaces extensive | match policer Policer: Input: __default_arp_policer__ <<< incorrect if user ARP Policer was applied on an AE interface and the default ARP Policer is displayed Policer: Input: jtac-arp-ae5.317-inet-arp <<< correct if user ARP Policer was applied on an AE interface For all platforms, except SRX Series: This issue affects Juniper Networks Junos OS: All versions 5.6R1 and all later versions prior to 18.4 versions prior to 18.4R2-S9, 18.4R3-S9 with the exception of 15.1 versions 15.1R7-S10 and later versions; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; This issue does not affect Juniper Networks Junos OS versions prior to 5.6R1. On SRX Series this issue affects Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.4 versions prior to 19.4R3-S4; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect 18.4 versions prior to 18.4R1 on SRX Series. This issue does not affect Junos OS Evolved. | ||||
| CVE-2020-1661 | 1 Juniper | 32 Ex2300, Ex2300-c, Ex3400 and 29 more | 2024-09-17 | 5.3 Medium |
| On Juniper Networks Junos OS devices configured as a DHCP forwarder, the Juniper Networks Dynamic Host Configuration Protocol Daemon (jdhcp) process might crash when receiving a malformed DHCP packet. This issue only affects devices configured as DHCP forwarder with forward-only option, that forward specified DHCP client packets, without creating a new subscriber session. The jdhcpd daemon automatically restarts without intervention, but continuous receipt of the malformed DHCP packet will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue can be triggered only by DHCPv4, it cannot be triggered by DHCPv6. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S16; 12.3X48 versions prior to 12.3X48-D105 on SRX Series; 14.1X53 versions prior to 14.1X53-D60 on EX and QFX Series; 15.1 versions prior to 15.1R7-S7; 15.1X49 versions prior to 15.1X49-D221, 15.1X49-D230 on SRX Series; 15.1X53 versions prior to 15.1X53-D593 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S5. | ||||
| CVE-2021-0294 | 1 Juniper | 8 Ex4600, Ex4650, Junos and 5 more | 2024-09-17 | 5.3 Medium |
| A vulnerability in Juniper Networks Junos OS, which only affects the release 18.4R2-S5, where a function is inconsistently implemented on Juniper Networks Junos QFX5000 Series and EX4600 Series, and if "storm-control enhanced" is configured, can lead to the enhanced storm control filter group not be installed. It will cause storm control not to work hence allowing an attacker to cause high CPU usage or packet loss issues by sending a large amount of broadcast or unknown unicast packets arriving the device. This issue affects Juniper Networks QFX5100, QFX5110, QFX5120, QFX5200, QFX5210, EX4600, and EX4650, and QFX5100 with QFX 5e Series image installed. QFX5130 and QFX5220 are not affected from this issue. This issue affects Juniper Networks Junos OS 18.4R2-S5 on QFX5000 Series and EX4600 Series. No other product or platform is affected by this vulnerability. | ||||
| CVE-2021-0237 | 1 Juniper | 11 Ex4300-mp, Ex4600, Ex4650 and 8 more | 2024-09-17 | 6.5 Medium |
| On Juniper Networks EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series deployed as a Virtual Chassis with a specific Layer 2 circuit configuration, Packet Forwarding Engine manager (FXPC) process may crash and restart upon receipt of specific layer 2 frames. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4, 17.4R3-S5; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2; | ||||
| CVE-2021-0217 | 1 Juniper | 21 Ex2300, Ex2300-c, Ex2300m and 18 more | 2024-09-17 | 7.4 High |
| A vulnerability in processing of certain DHCP packets from adjacent clients on EX Series and QFX Series switches running Juniper Networks Junos OS with DHCP local/relay server configured may lead to exhaustion of DMA memory causing a Denial of Service (DoS). Over time, exploitation of this vulnerability may cause traffic to stop being forwarded, or to crashing of the fxpc process. When Packet DMA heap utilization reaches 99%, the system will become unstable. Packet DMA heap utilization can be monitored through the following command: user@junos# request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 213301a8 536870488 387228840 149641648 27 Kernel 1 91800000 8388608 3735120 4653488 55 DMA 2 92000000 75497472 74452192 1045280 1 PKT DMA DESC 3 d330000 335544320 257091400 78452920 23 Bcm_sdk 4 96800000 184549376 2408 184546968 99 Packet DMA <--- 5 903fffe0 20971504 20971504 0 0 Blob An indication of the issue occurring may be observed through the following log messages: Dec 10 08:07:00.124 2020 hostname fpc0 brcm_pkt_buf_alloc:523 (buf alloc) failed allocating packet buffer Dec 10 08:07:00.126 2020 hostname fpc0 (buf alloc) failed allocating packet buffer Dec 10 08:07:00.128 2020 hostname fpc0 brcm_pkt_buf_alloc:523 (buf alloc) failed allocating packet buffer Dec 10 08:07:00.130 2020 hostnameC fpc0 (buf alloc) failed allocating packet buffer This issue affects Juniper Networks Junos OS on EX Series and QFX Series: 17.4R3 versions prior to 17.4R3-S3; 18.1R3 versions between 18.1R3-S6 and 18.1R3-S11; 18.2R3 versions prior to 18.2R3-S6; 18.3R3 versions prior to 18.3R3-S4; 18.4R2 versions prior to 18.4R2-S5; 18.4R3 versions prior to 18.4R3-S6; 19.1 versions between 19.1R2 and 19.1R3-S3; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S2, 20.2R2. Junos OS versions prior to 17.4R3 are unaffected by this vulnerability. | ||||
| CVE-2020-1618 | 1 Juniper | 16 Ex2300, Ex2300-c, Ex3400 and 13 more | 2024-09-17 | 6.3 Medium |
| On Juniper Networks EX and QFX Series, an authentication bypass vulnerability may allow a user connected to the console port to login as root without any password. This issue might only occur in certain scenarios: • At the first reboot after performing device factory reset using the command “request system zeroize”; or • A temporary moment during the first reboot after the software upgrade when the device configured in Virtual Chassis mode. This issue affects Juniper Networks Junos OS on EX and QFX Series: 14.1X53 versions prior to 14.1X53-D53; 15.1 versions prior to 15.1R7-S4; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S4; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R2; 18.3 versions prior to 18.3R1-S7, 18.3R2. This issue does not affect Juniper Networks Junos OS 12.3. | ||||
| CVE-2021-31370 | 1 Juniper | 15 Ex4600, Ex4600-vc, Ex4650 and 12 more | 2024-09-17 | 6.5 Medium |
| An Incomplete List of Disallowed Inputs vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX5000 Series and EX4600 Series allows an adjacent unauthenticated attacker which sends a high rate of specific multicast traffic to cause control traffic received from the network to be dropped. This will impact control protocols (including but not limited to routing-protocols) and lead to a Denial of Service (DoS). Continued receipt of this specific multicast traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX5000 and EX4600 Series: All versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2. | ||||
| CVE-2021-0203 | 1 Juniper | 17 Ex2300, Ex2300-c, Ex2300m and 14 more | 2024-09-17 | 8.6 High |
| On Juniper Networks EX and QFX5K Series platforms configured with Redundant Trunk Group (RTG), Storm Control profile applied on the RTG interface might not take affect when it reaches the threshold condition. Storm Control enables the device to monitor traffic levels and to drop broadcast, multicast, and unknown unicast packets when a specified traffic level is exceeded, thus preventing packets from proliferating and degrading the LAN. Note: this issue does not affect EX2200, EX3300, EX4200, and EX9200 Series. This issue affects Juniper Networks Junos OS on EX Series and QFX5K Series: 15.1 versions prior to 15.1R7-S7; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S5, 18.4R3-S3; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. | ||||
| CVE-2019-0043 | 1 Juniper | 47 Acx1000, Acx1100, Acx2000 and 44 more | 2024-09-17 | 7.5 High |
| In MPLS environments, receipt of a specific SNMP packet may cause the routing protocol daemon (RPD) process to crash and restart. By continuously sending a specially crafted SNMP packet, an attacker can repetitively crash the RPD process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS : 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D48 on EX/QFX series; 15.1 versions prior to 15.1R4-S9, 15.1R7-S2; 15.1F6 versions prior to 15.1F6-S11; 15.1X49 versions prior to 15.1X49-D141, 15.1X49-D144, 15.1X49-D150 on SRX Series; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 15.1X53 versions prior to 15.1X53-D590 on EX2300/EX3400 Series; 15.1X54 on ACX Series; 16.1 versions prior to 16.1R3-S10, 16.1R4-S11, 16.1R6-S5, 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S6; 17.1 versions prior to 17.1R2-S8, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R1-S1, 18.1R2-S1, 18.1R3; 18.2X75 versions prior to 18.2X75-D10. | ||||
| CVE-2021-0275 | 1 Juniper | 24 Ex2300, Ex2300-c, Ex3400 and 21 more | 2024-09-17 | 8.8 High |
| A Cross-site Scripting (XSS) vulnerability in J-Web on Juniper Networks Junos OS allows an attacker to target another user's session thereby gaining access to the users session. The other user session must be active for the attack to succeed. Once successful, the attacker has the same privileges as the user. If the user has root privileges, the attacker may be able to gain full control of the device. This issue affects: Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15 on EX Series; 12.3X48 versions prior to 12.3X48-D95 on SRX Series; 15.1 versions prior to 15.1R7-S6 on EX Series; 15.1X49 versions prior to 15.1X49-D200 on SRX Series; 16.1 versions prior to 16.1R7-S7; 16.2 versions prior to 16.2R2-S11, 16.2R3; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3-S1; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3; 19.1 versions prior to 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S3, 19.2R2; 19.3 versions prior to 19.3R2. | ||||
| CVE-2022-22221 | 1 Juniper | 86 Ex2200, Ex2200-c, Ex2200-vc and 83 more | 2024-09-17 | 7.8 High |
| An Improper Neutralization of Special Elements vulnerability in the download manager of Juniper Networks Junos OS on SRX Series and EX Series allows a locally authenticated attacker with low privileges to take full control over the device. One aspect of this vulnerability is that the attacker needs to be able to execute any of the "request ..." or "show system download ..." commands. This issue affects Juniper Networks Junos OS on SRX Series and EX Series: All versions prior to 19.2R1-S9, 19.2R3-S5; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S8; 20.1 versions prior to 20.1R3-S4; 20.2 versions prior to 20.2R3-S4; 20.3 versions prior to 20.3R3-S3; 20.4 versions prior to 20.4R3-S2, 20.4R3-S3; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R2-S2, 21.2R3; 21.3 versions prior to 21.3R2, 21.3R3; 21.4 versions prior to 21.4R1-S1, 21.4R2. | ||||
| CVE-2019-0062 | 1 Juniper | 46 Csrx, Ex2200, Ex2200-c and 43 more | 2024-09-16 | 7.5 High |
| A session fixation vulnerability in J-Web on Junos OS may allow an attacker to use social engineering techniques to fix and hijack a J-Web administrators web session and potentially gain administrative access to the device. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15 on EX Series; 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 14.1X53 versions prior to 14.1X53-D51; 15.1 versions prior to 15.1F6-S13, 15.1R7-S5; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238; 16.1 versions prior to 16.1R4-S13, 16.1R7-S5; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.3 versions prior to 17.3R3-S5; 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S2, 19.1R2. | ||||
| CVE-2018-0043 | 1 Juniper | 48 Ex2200, Ex2200-c, Ex2300 and 45 more | 2024-09-16 | N/A |
| Receipt of a specific MPLS packet may cause the routing protocol daemon (RPD) process to crash and restart or may lead to remote code execution. By continuously sending specific MPLS packets, an attacker can repeatedly crash the RPD process causing a sustained Denial of Service. This issue affects both IPv4 and IPv6. This issue can only be exploited from within the MPLS domain. End-users connected to the CE device cannot cause this crash. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on QFX/EX Series; 14.1X53 versions prior to 14.1X53-D130 on QFabric Series; 15.1F6 versions prior to 15.1F6-S10; 15.1 versions prior to 15.1R4-S9 15.1R7; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D471 15.1X53-D490 on NFX Series; 16.1 versions prior to 16.1R3-S8 16.1R4-S8 16.1R5-S4 16.1R6-S4 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R1-S6 16.2R3; 17.1 versions prior to 17.1R1-S7 17.1R2-S6 17.1R3; 17.2 versions prior to 17.2R1-S6 17.2R2-S3 17.2R3; 17.2X75 versions prior to 17.2X75-D100 17.2X75-D42 17.2X75-D91; 17.3 versions prior to 17.3R1-S4 17.3R2-S2 17.3R3; 17.4 versions prior to 17.4R1-S3 17.4R2 . No other Juniper Networks products or platforms are affected by this issue. | ||||
| CVE-2022-22203 | 1 Juniper | 11 Ex4600, Ex4650, Junos and 8 more | 2024-09-16 | 6.5 Medium |
| An Incorrect Comparison vulnerability in PFE of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a Denial of Service (DoS). On QFX5000 Series, and EX4600 and EX4650 platforms, the fxpc process will crash followed by the FPC reboot upon receipt of a specific hostbound packet. Continued receipt of these specific packets will create a sustained Denial of Service (DoS) condition. This issue only affects Juniper Networks Junos OS 19.4 version 19.4R3-S4. | ||||
| CVE-2021-0211 | 1 Juniper | 87 Ex2200, Ex2200-c, Ex2200-vc and 84 more | 2024-09-16 | 10 Critical |
| An improper check for unusual or exceptional conditions in Juniper Networks Junos OS and Junos OS Evolved Routing Protocol Daemon (RPD) service allows an attacker to send a valid BGP FlowSpec message thereby causing an unexpected change in the route advertisements within the BGP FlowSpec domain leading to disruptions in network traffic causing a Denial of Service (DoS) condition. Continued receipt of these update messages will cause a sustained Denial of Service condition. This issue affects Juniper Networks: Junos OS: All versions prior to 17.3R3-S10 with the exceptions of 15.1X49-D240 on SRX Series and 15.1R7-S8 on EX Series; 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R2-S12, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S3; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R1-S3, 19.4R2-S3, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S3 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2. Junos OS Evolved: All versions prior to 20.3R1-S1-EVO, 20.3R2-EVO. | ||||
| CVE-2020-1607 | 1 Juniper | 44 Ex2300, Ex2300-c, Ex3400 and 41 more | 2024-09-16 | 7.5 High |
| Insufficient Cross-Site Scripting (XSS) protection in J-Web may potentially allow a remote attacker to inject web script or HTML, hijack the target user's J-Web session and perform administrative actions on the Junos device as the targeted user. This issue affects Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D86, 12.3X48-D90 on SRX Series; 14.1X53 versions prior to 14.1X53-D51 on EX and QFX Series; 15.1F6 versions prior to 15.1F6-S13; 15.1 versions prior to 15.1R7-S5; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400 Series; 16.1 versions prior to 16.1R4-S13, 16.1R7-S5; 16.2 versions prior to 16.2R2-S10; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R1-S9, 17.2R3-S2; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R2-S6, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.3 versions prior to 18.3R1-S6, 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S2, 19.1R2. | ||||
| CVE-2022-22174 | 1 Juniper | 12 Ex4600, Ex4600-vc, Ex4650 and 9 more | 2024-09-16 | 7.5 High |
| A vulnerability in the processing of inbound IPv6 packets in Juniper Networks Junos OS on QFX5000 Series and EX4600 switches may cause the memory to not be freed, leading to a packet DMA memory leak, and eventual Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition. The following error logs may be observed using the "show heap" command and the device may eventually run out of memory if such packets are received continuously. Jan 12 12:00:00 device-name fpc0 (buf alloc) failed allocating packet buffer Jan 12 12:00:01 device-name fpc0 (buf alloc) failed allocating packet buffer user@device-name> request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 246fc1a8 536870488 353653752 183216736 34 Kernel 1 91800000 16777216 12069680 4707536 28 DMA 2 92800000 75497472 69997640 5499832 7 PKT DMA DESC 3 106fc000 335544320 221425960 114118360 34 Bcm_sdk 4 97000000 176160768 200 176160568 99 Packet DMA <<<<<<<<<<<<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects Juniper Networks Junos OS on QFX5000 Series, EX4600: 18.3R3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue does not affect Juniper Networks Junos OS: Any versions prior to 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2. | ||||