Filtered by vendor Juniper
Subscriptions
Filtered by product Srx5400
Subscriptions
Total
105 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2017-10619 | 1 Juniper | 7 Junos, Srx1400, Srx3400 and 4 more | 2025-04-20 | N/A |
| When Express Path (formerly known as service offloading) is configured on Juniper Networks SRX1400, SRX3400, SRX3600, SRX5400, SRX5600, SRX5800 in high availability cluster configuration mode, certain multicast packets might cause the flowd process to crash, halting or interrupting traffic from flowing through the device and triggering RG1+ (data-plane) fail-over to the secondary node. Repeated crashes of the flowd process may constitute an extended denial of service condition. This service is not enabled by default and is only supported in high-end SRX platforms. Affected releases are Juniper Networks Junos OS 12.3X48 prior to 12.3X48-D45, 15.1X49 prior to 15.1X49-D80 on SRX1400, SRX3400, SRX3600, SRX5400, SRX5600, SRX5800. | ||||
| CVE-2017-10608 | 1 Juniper | 13 Junos, Srx110, Srx1400 and 10 more | 2025-04-20 | N/A |
| Any Juniper Networks SRX series device with one or more ALGs enabled may experience a flowd crash when traffic is processed by the Sun/MS-RPC ALGs. This vulnerability in the Sun/MS-RPC ALG services component of Junos OS allows an attacker to cause a repeated denial of service against the target. Repeated traffic in a cluster may cause repeated flip-flop failure operations or full failure to the flowd daemon halting traffic on all nodes. Only IPv6 traffic is affected by this issue. IPv4 traffic is unaffected. This issues is not seen with to-host traffic. This issue has no relation with HA services themselves, only the ALG service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D55 on SRX; 12.1X47 prior to 12.1X47-D45 on SRX; 12.3X48 prior to 12.3X48-D32, 12.3X48-D35 on SRX; 15.1X49 prior to 15.1X49-D60 on SRX. | ||||
| CVE-2017-10605 | 1 Juniper | 14 Junos, Srx100, Srx110 and 11 more | 2025-04-20 | N/A |
| On all vSRX and SRX Series devices, when the DHCP or DHCP relay is configured, specially crafted packet might cause the flowd process to crash, halting or interrupting traffic from flowing through the device(s). Repeated crashes of the flowd process may constitute an extended denial of service condition for the device(s). If the device is configured in high-availability, the RG1+ (data-plane) will fail-over to the secondary node. If the device is configured in stand-alone, there will be temporary traffic interruption until the flowd process is restored automatically. Sustained crafted packets may cause the secondary failover node to fail back, or fail completely, potentially halting flowd on both nodes of the cluster or causing flip-flop failovers to occur. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D67 on vSRX or SRX Series; 12.3X48 prior to 12.3X48-D50 on vSRX or SRX Series; 15.1X49 prior to 15.1X49-D91, 15.1X49-D100 on vSRX or SRX Series. | ||||
| CVE-2017-2343 | 1 Juniper | 14 Junos, Srx100, Srx110 and 11 more | 2025-04-20 | N/A |
| The Integrated User Firewall (UserFW) feature was introduced in Junos OS version 12.1X47-D10 on the Juniper SRX Series devices to provide simple integration of user profiles on top of the existing firewall polices. As part of an internal security review of the UserFW services authentication API, hardcoded credentials were identified and removed which can impact both the SRX Series device, and potentially LDAP and Active Directory integrated points. An attacker may be able to completely compromise SRX Series devices, as well as Active Directory servers and services. When Active Directory is compromised, it may allow access to user credentials, workstations, servers performing other functions such as email, database, etc. Inter-Forest Active Directory deployments may also be at risk as the attacker may gain full administrative control over one or more Active Directories depending on the credentials supplied by the administrator of the AD domains and SRX devices performing integrated authentication of users, groups and devices. To identify if your device is potentially vulnerable to exploitation, check to see if the service is operating; from CLI review the following output: root@SRX-Firewall# run show services user-identification active-directory-access domain-controller status extensive A result of "Status: Connected" will indicate that the service is active on the device. To evaluate if user authentication is occurring through the device: root@SRX-Firewall# run show services user-identification active-directory-access active-directory-authentication-table all Next review the results to see if valid users and groups are returned. e.g. Domain: juniperlab.com Total entries: 3 Source IP Username groups state 172.16.26.1 administrator Valid 192.168.26.2 engg01 engineers Valid 192.168.26.3 guest01 guests Valid Domain: NULL Total entries: 8 Source IP Username groups state 192.168.26.4 Invalid 192.168.26.5 Invalid This will also indicate that Valid users and groups are authenticating through the device. Affected releases are Juniper Networks Junos OS 12.3X48 from 12.3X48-D30 and prior to 12.3X48-D35 on SRX series; 15.1X49 from 15.1X49-D40 and prior to 15.1X49-D50 on SRX series. Devices on any version of Junos OS 12.1X46, or 12.1X47 are unaffected by this issue. | ||||
| CVE-2017-10620 | 1 Juniper | 21 Junos, Srx100, Srx110 and 18 more | 2025-04-20 | N/A |
| Juniper Networks Junos OS on SRX series devices do not verify the HTTPS server certificate before downloading anti-virus updates. This may allow a man-in-the-middle attacker to inject bogus signatures to cause service disruptions or make the device not detect certain types of attacks. Affected Junos OS releases are: 12.1X46 prior to 12.1X46-D71; 12.3X48 prior to 12.3X48-D55; 15.1X49 prior to 15.1X49-D110; | ||||
| CVE-2015-5363 | 1 Juniper | 14 Junos, Srx100, Srx110 and 11 more | 2025-04-12 | N/A |
| The SRX Network Security Daemon (nsd) in Juniper SRX Series services gateways with Junos 12.1X44 before 12.1X44-D50, 12.1X46 before 12.1X46-D35, 12.1X47 before 12.1X47-D25, and 12.3X48 before 12.3X48-D15 allows remote DNS servers to cause a denial of service (crash) via a crafted DNS response. | ||||
| CVE-2014-9708 | 3 Embedthis, Juniper, Oracle | 134 Appweb, Ex2200, Ex2200-c and 131 more | 2025-04-12 | N/A |
| Embedthis Appweb before 4.6.6 and 5.x before 5.2.1 allows remote attackers to cause a denial of service (NULL pointer dereference) via a Range header with an empty value, as demonstrated by "Range: x=,". | ||||
| CVE-2016-1286 | 8 Canonical, Debian, Fedoraproject and 5 more | 51 Ubuntu Linux, Debian Linux, Fedora and 48 more | 2025-04-12 | 8.6 High |
| named in ISC BIND 9.x before 9.9.8-P4 and 9.10.x before 9.10.3-P4 allows remote attackers to cause a denial of service (assertion failure and daemon exit) via a crafted signature record for a DNAME record, related to db.c and resolver.c. | ||||
| CVE-2016-1285 | 8 Canonical, Debian, Fedoraproject and 5 more | 51 Ubuntu Linux, Debian Linux, Fedora and 48 more | 2025-04-12 | 6.8 Medium |
| named in ISC BIND 9.x before 9.9.8-P4 and 9.10.x before 9.10.3-P4 does not properly handle DNAME records when parsing fetch reply messages, which allows remote attackers to cause a denial of service (assertion failure and daemon exit) via a malformed packet to the rndc (aka control channel) interface, related to alist.c and sexpr.c. | ||||
| CVE-2024-39540 | 1 Juniper | 38 Csrx, Junos, Mx240 and 35 more | 2025-04-11 | 7.5 High |
| An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on SRX Series, and MX Series with SPC3 allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). When an affected device receives specific valid TCP traffic, the pfe crashes and restarts leading to a momentary but complete service outage. This issue affects Junos OS: 21.2 releases from 21.2R3-S5 before 21.2R3-S6. This issue does not affect earlier or later releases. | ||||
| CVE-2024-30391 | 1 Juniper | 38 Csrx, Junos, Mx240 and 35 more | 2025-04-11 | 4.8 Medium |
| A Missing Authentication for Critical Function vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series with SPC3, and SRX Series allows an unauthenticated network-based attacker to cause limited impact to the integrity or availability of the device. If a device is configured with IPsec authentication algorithm hmac-sha-384 or hmac-sha-512, tunnels are established normally but for traffic traversing the tunnel no authentication information is sent with the encrypted data on egress, and no authentication information is expected on ingress. So if the peer is an unaffected device transit traffic is going to fail in both directions. If the peer is an also affected device transit traffic works, but without authentication, and configuration and CLI operational commands indicate authentication is performed. This issue affects Junos OS: * All versions before 20.4R3-S7, * 21.1 versions before 21.1R3, * 21.2 versions before 21.2R2-S1, 21.2R3, * 21.3 versions before 21.3R1-S2, 21.3R2. | ||||
| CVE-2024-30405 | 1 Juniper | 4 Junos, Srx5400, Srx5600 and 1 more | 2025-04-10 | 7.5 High |
| An Incorrect Calculation of Buffer Size vulnerability in Juniper Networks Junos OS SRX 5000 Series devices using SPC2 line cards while ALGs are enabled allows an attacker sending specific crafted packets to cause a transit traffic Denial of Service (DoS). Continued receipt and processing of these specific packets will sustain the Denial of Service condition. This issue affects: Juniper Networks Junos OS SRX 5000 Series with SPC2 with ALGs enabled. * All versions earlier than 21.2R3-S7; * 21.4 versions earlier than 21.4R3-S6; * 22.1 versions earlier than 22.1R3-S5; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R2. | ||||
| CVE-2024-21609 | 1 Juniper | 38 Csrx, Junos, Mx240 and 35 more | 2025-04-10 | 6.5 Medium |
| A Missing Release of Memory after Effective Lifetime vulnerability in the IKE daemon (iked) of Juniper Networks Junos OS on MX Series with SPC3, and SRX Series allows an administratively adjacent attacker which is able to successfully establish IPsec tunnels to cause a Denial of Service (DoS). If specific values for the IPsec parameters local-ip, remote-ip, remote ike-id, and traffic selectors are sent from the peer, a memory leak occurs during every IPsec SA rekey which is carried out with a specific message sequence. This will eventually result in an iked process crash and restart. The iked process memory consumption can be checked using the below command: user@host> show system processes extensive | grep iked PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 56903 root 31 0 4016M 2543M CPU0 0 2:10 10.50% iked This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S3; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R3; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2. | ||||
| CVE-2024-39561 | 1 Juniper | 6 Junos, Srx4600, Srx5000 and 3 more | 2025-04-10 | 5.8 Medium |
| An Improper Check for Unusual or Exceptional Conditions vulnerability in the flow daemon (flowd) of Juniper Networks Junos OS on SRX4600 and SRX5000 Series allows an attacker to send TCP packets with SYN/FIN or SYN/RST flags, bypassing the expected blocking of these packets. A TCP packet with SYN/FIN or SYN/RST should be dropped in flowd. However, when no-syn-check and Express Path are enabled, these TCP packets are unexpectedly transferred to the downstream network. This issue affects Junos OS on SRX4600 and SRX5000 Series: * All versions before 21.2R3-S8, * from 21.4 before 21.4R3-S7, * from 22.1 before 22.1R3-S6, * from 22.2 before 22.2R3-S4, * from 22.3 before 22.3R3-S3, * from 22.4 before 22.4R3-S2, * from 23.2 before 23.2R2, * from 23.4 before 23.4R1-S1, 23.4R2. | ||||
| CVE-2023-22416 | 1 Juniper | 46 Junos, Mx10, Mx10000 and 43 more | 2025-04-08 | 7.5 High |
| A Buffer Overflow vulnerability in SIP ALG of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On all MX Series and SRX Series platform with SIP ALG enabled, when a malformed SIP packet is received, the flow processing daemon (flowd) will crash and restart. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on SRX Series. | ||||
| CVE-2023-22417 | 1 Juniper | 29 Junos, Srx100, Srx110 and 26 more | 2025-04-08 | 7.5 High |
| A Missing Release of Memory after Effective Lifetime vulnerability in the Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In an IPsec VPN environment, a memory leak will be seen if a DH or ECDH group is configured. Eventually the flowd process will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2. | ||||
| CVE-2023-22415 | 1 Juniper | 46 Junos, Mx10, Mx10000 and 43 more | 2025-04-07 | 7.5 High |
| An Out-of-Bounds Write vulnerability in the H.323 ALG of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On all MX Series and SRX Series platform, when H.323 ALG is enabled and specific H.323 packets are received simultaneously, a flow processing daemon (flowd) crash will occur. Continued receipt of these specific packets will cause a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series All versions prior to 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2. | ||||
| CVE-2023-22394 | 1 Juniper | 46 Junos, Mx10, Mx10000 and 43 more | 2025-04-07 | 7.5 High |
| An Improper Handling of Unexpected Data Type vulnerability in the handling of SIP calls in Juniper Networks Junos OS on SRX Series and MX Series platforms allows an attacker to cause a memory leak leading to Denial of Services (DoS). This issue occurs on all MX Series platforms with MS-MPC or MS-MIC card and all SRX Series platforms where SIP ALG is enabled. Successful exploitation of this vulnerability prevents additional SIP calls and applications from succeeding. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.1 versions 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2, 22.1R3-S1. This issue does not affect Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 18.2R1. | ||||
| CVE-2023-22404 | 1 Juniper | 46 Junos, Mx10, Mx10000 and 43 more | 2025-04-07 | 6.5 Medium |
| An Out-of-bounds Write vulnerability in the Internet Key Exchange Protocol daemon (iked) of Juniper Networks Junos OS on SRX series and MX with SPC3 allows an authenticated, network-based attacker to cause a Denial of Service (DoS). iked will crash and restart, and the tunnel will not come up when a peer sends a specifically formatted payload during the negotiation. This will impact other IKE negotiations happening at the same time. Continued receipt of this specifically formatted payload will lead to continuous crashing of iked and thereby the inability for any IKE negotiations to take place. Note that this payload is only processed after the authentication has successfully completed. So the issue can only be exploited by an attacker who can successfully authenticate. This issue affects Juniper Networks Junos OS on SRX Series, and MX Series with SPC3: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2. | ||||
| CVE-2023-22408 | 1 Juniper | 4 Junos, Srx5400, Srx5600 and 1 more | 2025-04-07 | 7.5 High |
| An Improper Validation of Array Index vulnerability in the SIP ALG of Juniper Networks Junos OS on SRX 5000 Series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an attacker sends an SIP packets with a malformed SDP field then the SIP ALG can not process it which will lead to an FPC crash and restart. Continued receipt of these specific packets will lead to a sustained Denial of Service. This issue can only occur when both below mentioned conditions are fulfilled: 1. Call distribution needs to be enabled: [security alg sip enable-call-distribution] 2. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX, and MX with SPC3 use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX 5000 Series: 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R1-S1, 22.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1. | ||||