In the Linux kernel, the following vulnerability has been resolved:
uio_hv_generic: Let userspace take care of interrupt mask
Remove the logic to set interrupt mask by default in uio_hv_generic
driver as the interrupt mask value is supposed to be controlled
completely by the user space. If the mask bit gets changed
by the driver, concurrently with user mode operating on the ring,
the mask bit may be set when it is supposed to be clear, and the
user-mode driver will miss an interrupt which will cause a hang.
For eg- when the driver sets inbound ring buffer interrupt mask to 1,
the host does not interrupt the guest on the UIO VMBus channel.
However, setting the mask does not prevent the host from putting a
message in the inbound ring buffer. So let’s assume that happens,
the host puts a message into the ring buffer but does not interrupt.
Subsequently, the user space code in the guest sets the inbound ring
buffer interrupt mask to 0, saying “Hey, I’m ready for interrupts”.
User space code then calls pread() to wait for an interrupt.
Then one of two things happens:
* The host never sends another message. So the pread() waits forever.
* The host does send another message. But because there’s already a
message in the ring buffer, it doesn’t generate an interrupt.
This is the correct behavior, because the host should only send an
interrupt when the inbound ring buffer transitions from empty to
not-empty. Adding an additional message to a ring buffer that is not
empty is not supposed to generate an interrupt on the guest.
Since the guest is waiting in pread() and not removing messages from
the ring buffer, the pread() waits forever.
This could be easily reproduced in hv_fcopy_uio_daemon if we delay
setting interrupt mask to 0.
Similarly if hv_uio_channel_cb() sets the interrupt_mask to 1,
there’s a race condition. Once user space empties the inbound ring
buffer, but before user space sets interrupt_mask to 0, the host could
put another message in the ring buffer but it wouldn’t interrupt.
Then the next pread() would hang.
Fix these by removing all instances where interrupt_mask is changed,
while keeping the one in set_event() unchanged to enable userspace
control the interrupt mask by writing 0/1 to /dev/uioX.
uio_hv_generic: Let userspace take care of interrupt mask
Remove the logic to set interrupt mask by default in uio_hv_generic
driver as the interrupt mask value is supposed to be controlled
completely by the user space. If the mask bit gets changed
by the driver, concurrently with user mode operating on the ring,
the mask bit may be set when it is supposed to be clear, and the
user-mode driver will miss an interrupt which will cause a hang.
For eg- when the driver sets inbound ring buffer interrupt mask to 1,
the host does not interrupt the guest on the UIO VMBus channel.
However, setting the mask does not prevent the host from putting a
message in the inbound ring buffer. So let’s assume that happens,
the host puts a message into the ring buffer but does not interrupt.
Subsequently, the user space code in the guest sets the inbound ring
buffer interrupt mask to 0, saying “Hey, I’m ready for interrupts”.
User space code then calls pread() to wait for an interrupt.
Then one of two things happens:
* The host never sends another message. So the pread() waits forever.
* The host does send another message. But because there’s already a
message in the ring buffer, it doesn’t generate an interrupt.
This is the correct behavior, because the host should only send an
interrupt when the inbound ring buffer transitions from empty to
not-empty. Adding an additional message to a ring buffer that is not
empty is not supposed to generate an interrupt on the guest.
Since the guest is waiting in pread() and not removing messages from
the ring buffer, the pread() waits forever.
This could be easily reproduced in hv_fcopy_uio_daemon if we delay
setting interrupt mask to 0.
Similarly if hv_uio_channel_cb() sets the interrupt_mask to 1,
there’s a race condition. Once user space empties the inbound ring
buffer, but before user space sets interrupt_mask to 0, the host could
put another message in the ring buffer but it wouldn’t interrupt.
Then the next pread() would hang.
Fix these by removing all instances where interrupt_mask is changed,
while keeping the one in set_event() unchanged to enable userspace
control the interrupt mask by writing 0/1 to /dev/uioX.
Metrics
Affected Vendors & Products
No data.
No data.
No data.
No data.
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Tue, 28 Oct 2025 12:00:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | In the Linux kernel, the following vulnerability has been resolved: uio_hv_generic: Let userspace take care of interrupt mask Remove the logic to set interrupt mask by default in uio_hv_generic driver as the interrupt mask value is supposed to be controlled completely by the user space. If the mask bit gets changed by the driver, concurrently with user mode operating on the ring, the mask bit may be set when it is supposed to be clear, and the user-mode driver will miss an interrupt which will cause a hang. For eg- when the driver sets inbound ring buffer interrupt mask to 1, the host does not interrupt the guest on the UIO VMBus channel. However, setting the mask does not prevent the host from putting a message in the inbound ring buffer. So let’s assume that happens, the host puts a message into the ring buffer but does not interrupt. Subsequently, the user space code in the guest sets the inbound ring buffer interrupt mask to 0, saying “Hey, I’m ready for interrupts”. User space code then calls pread() to wait for an interrupt. Then one of two things happens: * The host never sends another message. So the pread() waits forever. * The host does send another message. But because there’s already a message in the ring buffer, it doesn’t generate an interrupt. This is the correct behavior, because the host should only send an interrupt when the inbound ring buffer transitions from empty to not-empty. Adding an additional message to a ring buffer that is not empty is not supposed to generate an interrupt on the guest. Since the guest is waiting in pread() and not removing messages from the ring buffer, the pread() waits forever. This could be easily reproduced in hv_fcopy_uio_daemon if we delay setting interrupt mask to 0. Similarly if hv_uio_channel_cb() sets the interrupt_mask to 1, there’s a race condition. Once user space empties the inbound ring buffer, but before user space sets interrupt_mask to 0, the host could put another message in the ring buffer but it wouldn’t interrupt. Then the next pread() would hang. Fix these by removing all instances where interrupt_mask is changed, while keeping the one in set_event() unchanged to enable userspace control the interrupt mask by writing 0/1 to /dev/uioX. | |
| Title | uio_hv_generic: Let userspace take care of interrupt mask | |
| References |
|
|
MITRE
Status: PUBLISHED
Assigner: Linux
Published:
Updated: 2025-10-28T11:48:25.220Z
Reserved: 2025-04-16T07:20:57.156Z
Link: CVE-2025-40048
Vulnrichment
No data.
NVD
Status : Received
Published: 2025-10-28T12:15:38.920
Modified: 2025-10-28T12:15:38.920
Link: CVE-2025-40048
Redhat
No data.
OpenCVE Enrichment
No data.