| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ionic: remove WARN_ON to prevent panic_on_warn
Remove unnecessary early code development check and the WARN_ON
that it uses. The irq alloc and free paths have long been
cleaned up and this check shouldn't have stuck around so long. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: st: Fix memory leak in st_of_quadfs_setup()
If st_clk_register_quadfs_pll() fails, @lock should be freed before goto
@err_exit, otherwise will cause meory leak issue, fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix refcount leak in hns_roce_mmap
rdma_user_mmap_entry_get_pgoff() takes the reference.
Add missing rdma_user_mmap_entry_put() to release the reference.
Acked-by Haoyue Xu <xuhaoyue1@hisilicon.com> |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - fix DMA transfer direction
When CONFIG_DMA_API_DEBUG is selected, while running the crypto self
test on the QAT crypto algorithms, the function add_dma_entry() reports
a warning similar to the one below, saying that overlapping mappings
are not supported. This occurs in tests where the input and the output
scatter list point to the same buffers (i.e. two different scatter lists
which point to the same chunks of memory).
The logic that implements the mapping uses the flag DMA_BIDIRECTIONAL
for both the input and the output scatter lists which leads to
overlapped write mappings. These are not supported by the DMA layer.
Fix by specifying the correct DMA transfer directions when mapping
buffers. For in-place operations where the input scatter list
matches the output scatter list, buffers are mapped once with
DMA_BIDIRECTIONAL, otherwise input buffers are mapped using the flag
DMA_TO_DEVICE and output buffers are mapped with DMA_FROM_DEVICE.
Overlapping a read mapping with a write mapping is a valid case in
dma-coherent devices like QAT.
The function that frees and unmaps the buffers, qat_alg_free_bufl()
has been changed accordingly to the changes to the mapping function.
DMA-API: 4xxx 0000:06:00.0: cacheline tracking EEXIST, overlapping mappings aren't supported
WARNING: CPU: 53 PID: 4362 at kernel/dma/debug.c:570 add_dma_entry+0x1e9/0x270
...
Call Trace:
dma_map_page_attrs+0x82/0x2d0
? preempt_count_add+0x6a/0xa0
qat_alg_sgl_to_bufl+0x45b/0x990 [intel_qat]
qat_alg_aead_dec+0x71/0x250 [intel_qat]
crypto_aead_decrypt+0x3d/0x70
test_aead_vec_cfg+0x649/0x810
? number+0x310/0x3a0
? vsnprintf+0x2a3/0x550
? scnprintf+0x42/0x70
? valid_sg_divisions.constprop.0+0x86/0xa0
? test_aead_vec+0xdf/0x120
test_aead_vec+0xdf/0x120
alg_test_aead+0x185/0x400
alg_test+0x3d8/0x500
? crypto_acomp_scomp_free_ctx+0x30/0x30
? __schedule+0x32a/0x12a0
? ttwu_queue_wakelist+0xbf/0x110
? _raw_spin_unlock_irqrestore+0x23/0x40
? try_to_wake_up+0x83/0x570
? _raw_spin_unlock_irqrestore+0x23/0x40
? __set_cpus_allowed_ptr_locked+0xea/0x1b0
? crypto_acomp_scomp_free_ctx+0x30/0x30
cryptomgr_test+0x27/0x50
kthread+0xe6/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipv4: fix one memleak in __inet_del_ifa()
I got the below warning when do fuzzing test:
unregister_netdevice: waiting for bond0 to become free. Usage count = 2
It can be repoduced via:
ip link add bond0 type bond
sysctl -w net.ipv4.conf.bond0.promote_secondaries=1
ip addr add 4.117.174.103/0 scope 0x40 dev bond0
ip addr add 192.168.100.111/255.255.255.254 scope 0 dev bond0
ip addr add 0.0.0.4/0 scope 0x40 secondary dev bond0
ip addr del 4.117.174.103/0 scope 0x40 dev bond0
ip link delete bond0 type bond
In this reproduction test case, an incorrect 'last_prim' is found in
__inet_del_ifa(), as a result, the secondary address(0.0.0.4/0 scope 0x40)
is lost. The memory of the secondary address is leaked and the reference of
in_device and net_device is leaked.
Fix this problem:
Look for 'last_prim' starting at location of the deleted IP and inserting
the promoted IP into the location of 'last_prim'. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/sev: Make enc_dec_hypercall() accept a size instead of npages
enc_dec_hypercall() accepted a page count instead of a size, which
forced its callers to round up. As a result, non-page aligned
vaddrs caused pages to be spuriously marked as decrypted via the
encryption status hypercall, which in turn caused consistent
corruption of pages during live migration. Live migration requires
accurate encryption status information to avoid migrating pages
from the wrong perspective. |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: virtio - Fix race on data_avail and actual data
The virtio rng device kicks off a new entropy request whenever the
data available reaches zero. When a new request occurs at the end
of a read operation, that is, when the result of that request is
only needed by the next reader, then there is a race between the
writing of the new data and the next reader.
This is because there is no synchronisation whatsoever between the
writer and the reader.
Fix this by writing data_avail with smp_store_release and reading
it with smp_load_acquire when we first enter read. The subsequent
reads are safe because they're either protected by the first load
acquire, or by the completion mechanism.
Also remove the redundant zeroing of data_idx in random_recv_done
(data_idx must already be zero at this point) and data_avail in
request_entropy (ditto). |
| In the Linux kernel, the following vulnerability has been resolved:
staging: r8712: Fix memory leak in _r8712_init_xmit_priv()
In the above mentioned routine, memory is allocated in several places.
If the first succeeds and a later one fails, the routine will leak memory.
This patch fixes commit 2865d42c78a9 ("staging: r8712u: Add the new driver
to the mainline kernel"). A potential memory leak in
r8712_xmit_resource_alloc() is also addressed. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/fbdev-generic: prohibit potential out-of-bounds access
The fbdev test of IGT may write after EOF, which lead to out-of-bound
access for drm drivers with fbdev-generic. For example, run fbdev test
on a x86+ast2400 platform, with 1680x1050 resolution, will cause the
linux kernel hang with the following call trace:
Oops: 0000 [#1] PREEMPT SMP PTI
[IGT] fbdev: starting subtest eof
Workqueue: events drm_fb_helper_damage_work [drm_kms_helper]
[IGT] fbdev: starting subtest nullptr
RIP: 0010:memcpy_erms+0xa/0x20
RSP: 0018:ffffa17d40167d98 EFLAGS: 00010246
RAX: ffffa17d4eb7fa80 RBX: ffffa17d40e0aa80 RCX: 00000000000014c0
RDX: 0000000000001a40 RSI: ffffa17d40e0b000 RDI: ffffa17d4eb80000
RBP: ffffa17d40167e20 R08: 0000000000000000 R09: ffff89522ecff8c0
R10: ffffa17d4e4c5000 R11: 0000000000000000 R12: ffffa17d4eb7fa80
R13: 0000000000001a40 R14: 000000000000041a R15: ffffa17d40167e30
FS: 0000000000000000(0000) GS:ffff895257380000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffa17d40e0b000 CR3: 00000001eaeca006 CR4: 00000000001706e0
Call Trace:
<TASK>
? drm_fbdev_generic_helper_fb_dirty+0x207/0x330 [drm_kms_helper]
drm_fb_helper_damage_work+0x8f/0x170 [drm_kms_helper]
process_one_work+0x21f/0x430
worker_thread+0x4e/0x3c0
? __pfx_worker_thread+0x10/0x10
kthread+0xf4/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
</TASK>
CR2: ffffa17d40e0b000
---[ end trace 0000000000000000 ]---
The is because damage rectangles computed by
drm_fb_helper_memory_range_to_clip() function is not guaranteed to be
bound in the screen's active display area. Possible reasons are:
1) Buffers are allocated in the granularity of page size, for mmap system
call support. The shadow screen buffer consumed by fbdev emulation may
also choosed be page size aligned.
2) The DIV_ROUND_UP() used in drm_fb_helper_memory_range_to_clip()
will introduce off-by-one error.
For example, on a 16KB page size system, in order to store a 1920x1080
XRGB framebuffer, we need allocate 507 pages. Unfortunately, the size
1920*1080*4 can not be divided exactly by 16KB.
1920 * 1080 * 4 = 8294400 bytes
506 * 16 * 1024 = 8290304 bytes
507 * 16 * 1024 = 8306688 bytes
line_length = 1920*4 = 7680 bytes
507 * 16 * 1024 / 7680 = 1081.6
off / line_length = 507 * 16 * 1024 / 7680 = 1081
DIV_ROUND_UP(507 * 16 * 1024, 7680) will yeild 1082
memcpy_toio() typically issue the copy line by line, when copy the last
line, out-of-bound access will be happen. Because:
1082 * line_length = 1082 * 7680 = 8309760, and 8309760 > 8306688
Note that userspace may still write to the invisiable area if a larger
buffer than width x stride is exposed. But it is not a big issue as
long as there still have memory resolve the access if not drafting so
far.
- Also limit the y1 (Daniel)
- keep fix patch it to minimal (Daniel)
- screen_size is page size aligned because of it need mmap (Thomas)
- Adding fixes tag (Thomas) |
| In the Linux kernel, the following vulnerability has been resolved:
pcmcia: rsrc_nonstatic: Fix memory leak in nonstatic_release_resource_db()
When nonstatic_release_resource_db() frees all resources associated
with an PCMCIA socket, it forgets to free socket_data too, causing
a memory leak observable with kmemleak:
unreferenced object 0xc28d1000 (size 64):
comm "systemd-udevd", pid 297, jiffies 4294898478 (age 194.484s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 f0 85 0e c3 00 00 00 00 ................
00 00 00 00 0c 10 8d c2 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffda4245>] __kmem_cache_alloc_node+0x2d7/0x4a0
[<7e51f0c8>] kmalloc_trace+0x31/0xa4
[<d52b4ca0>] nonstatic_init+0x24/0x1a4 [pcmcia_rsrc]
[<a2f13e08>] pcmcia_register_socket+0x200/0x35c [pcmcia_core]
[<a728be1b>] yenta_probe+0x4d8/0xa70 [yenta_socket]
[<c48fac39>] pci_device_probe+0x99/0x194
[<84b7c690>] really_probe+0x181/0x45c
[<8060fe6e>] __driver_probe_device+0x75/0x1f4
[<b9b76f43>] driver_probe_device+0x28/0xac
[<648b766f>] __driver_attach+0xeb/0x1e4
[<6e9659eb>] bus_for_each_dev+0x61/0xb4
[<25a669f3>] driver_attach+0x1e/0x28
[<d8671d6b>] bus_add_driver+0x102/0x20c
[<df0d323c>] driver_register+0x5b/0x120
[<942cd8a4>] __pci_register_driver+0x44/0x4c
[<e536027e>] __UNIQUE_ID___addressable_cleanup_module188+0x1c/0xfffff000 [iTCO_vendor_support]
Fix this by freeing socket_data too.
Tested on a Acer Travelmate 4002WLMi by manually binding/unbinding
the yenta_cardbus driver (yenta_socket). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix assertion of exclop condition when starting balance
Balance as exclusive state is compatible with paused balance and device
add, which makes some things more complicated. The assertion of valid
states when starting from paused balance needs to take into account two
more states, the combinations can be hit when there are several threads
racing to start balance and device add. This won't typically happen when
the commands are started from command line.
Scenario 1: With exclusive_operation state == BTRFS_EXCLOP_NONE.
Concurrently adding multiple devices to the same mount point and
btrfs_exclop_finish executed finishes before assertion in
btrfs_exclop_balance, exclusive_operation will changed to
BTRFS_EXCLOP_NONE state which lead to assertion failed:
fs_info->exclusive_operation == BTRFS_EXCLOP_BALANCE ||
fs_info->exclusive_operation == BTRFS_EXCLOP_DEV_ADD,
in fs/btrfs/ioctl.c:456
Call Trace:
<TASK>
btrfs_exclop_balance+0x13c/0x310
? memdup_user+0xab/0xc0
? PTR_ERR+0x17/0x20
btrfs_ioctl_add_dev+0x2ee/0x320
btrfs_ioctl+0x9d5/0x10d0
? btrfs_ioctl_encoded_write+0xb80/0xb80
__x64_sys_ioctl+0x197/0x210
do_syscall_64+0x3c/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Scenario 2: With exclusive_operation state == BTRFS_EXCLOP_BALANCE_PAUSED.
Concurrently adding multiple devices to the same mount point and
btrfs_exclop_balance executed finish before the latter thread execute
assertion in btrfs_exclop_balance, exclusive_operation will changed to
BTRFS_EXCLOP_BALANCE_PAUSED state which lead to assertion failed:
fs_info->exclusive_operation == BTRFS_EXCLOP_BALANCE ||
fs_info->exclusive_operation == BTRFS_EXCLOP_DEV_ADD ||
fs_info->exclusive_operation == BTRFS_EXCLOP_NONE,
fs/btrfs/ioctl.c:458
Call Trace:
<TASK>
btrfs_exclop_balance+0x240/0x410
? memdup_user+0xab/0xc0
? PTR_ERR+0x17/0x20
btrfs_ioctl_add_dev+0x2ee/0x320
btrfs_ioctl+0x9d5/0x10d0
? btrfs_ioctl_encoded_write+0xb80/0xb80
__x64_sys_ioctl+0x197/0x210
do_syscall_64+0x3c/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
An example of the failed assertion is below, which shows that the
paused balance is also needed to be checked.
root@syzkaller:/home/xsk# ./repro
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
Failed to add device /dev/vda, errno 14
[ 416.611428][ T7970] BTRFS info (device loop0): fs_info exclusive_operation: 0
Failed to add device /dev/vda, errno 14
[ 416.613973][ T7971] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.615456][ T7972] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.617528][ T7973] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.618359][ T7974] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.622589][ T7975] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.624034][ T7976] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.626420][ T7977] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.627643][ T7978] BTRFS info (device loop0): fs_info exclusive_operation: 3
Failed to add device /dev/vda, errno 14
[ 416.629006][ T7979] BTRFS info (device loop0): fs_info exclusive_operation: 3
[ 416.630298][ T7980] BTRFS info (device loop0): fs_info exclusive_operation: 3
Fai
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix memory leak in binder_init()
In binder_init(), the destruction of binder_alloc_shrinker_init() is not
performed in the wrong path, which will cause memory leaks. So this commit
introduces binder_alloc_shrinker_exit() and calls it in the wrong path to
fix that. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: cadence: cdns_i2c_master_xfer(): Fix runtime PM leak on error path
The cdns_i2c_master_xfer() function gets a runtime PM reference when the
function is entered. This reference is released when the function is
exited. There is currently one error path where the function exits
directly, which leads to a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference. |
| In the Linux kernel, the following vulnerability has been resolved:
net: fix stack overflow when LRO is disabled for virtual interfaces
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
team0
|
+------+------+-----+-----+
| | | | |
team1 team2 team3 ... team200
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Check valid rport returned by fc_bsg_to_rport()
Klocwork reported warning of rport maybe NULL and will be dereferenced.
rport returned by call to fc_bsg_to_rport() could be NULL and dereferenced.
Check valid rport returned by fc_bsg_to_rport(). |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Devcom, fix error flow in mlx5_devcom_register_device
In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: sf-pdma: pdma_desc memory leak fix
Commit b2cc5c465c2c ("dmaengine: sf-pdma: Add multithread support for a
DMA channel") changed sf_pdma_prep_dma_memcpy() to unconditionally
allocate a new sf_pdma_desc each time it is called.
The driver previously recycled descs, by checking the in_use flag, only
allocating additional descs if the existing one was in use. This logic
was removed in commit b2cc5c465c2c ("dmaengine: sf-pdma: Add multithread
support for a DMA channel"), but sf_pdma_free_desc() was not changed to
handle the new behaviour.
As a result, each time sf_pdma_prep_dma_memcpy() is called, the previous
descriptor is leaked, over time leading to memory starvation:
unreferenced object 0xffffffe008447300 (size 192):
comm "irq/39-mchp_dsc", pid 343, jiffies 4294906910 (age 981.200s)
hex dump (first 32 bytes):
00 00 00 ff 00 00 00 00 b8 c1 00 00 00 00 00 00 ................
00 00 70 08 10 00 00 00 00 00 00 c0 00 00 00 00 ..p.............
backtrace:
[<00000000064a04f4>] kmemleak_alloc+0x1e/0x28
[<00000000018927a7>] kmem_cache_alloc+0x11e/0x178
[<000000002aea8d16>] sf_pdma_prep_dma_memcpy+0x40/0x112
Add the missing kfree() to sf_pdma_free_desc(), and remove the redundant
in_use flag. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: set goal start correctly in ext4_mb_normalize_request
We need to set ac_g_ex to notify the goal start used in
ext4_mb_find_by_goal. Set ac_g_ex instead of ac_f_ex in
ext4_mb_normalize_request.
Besides we should assure goal start is in range [first_data_block,
blocks_count) as ext4_mb_initialize_context does.
[ Added a check to make sure size is less than ar->pright; otherwise
we could end up passing an underflowed value of ar->pright - size to
ext4_get_group_no_and_offset(), which will trigger a BUG_ON later on.
- TYT ] |
| In the Linux kernel, the following vulnerability has been resolved:
opp: Fix use-after-free in lazy_opp_tables after probe deferral
When dev_pm_opp_of_find_icc_paths() in _allocate_opp_table() returns
-EPROBE_DEFER, the opp_table is freed again, to wait until all the
interconnect paths are available.
However, if the OPP table is using required-opps then it may already
have been added to the global lazy_opp_tables list. The error path
does not remove the opp_table from the list again.
This can cause crashes later when the provider of the required-opps
is added, since we will iterate over OPP tables that have already been
freed. E.g.:
Unable to handle kernel NULL pointer dereference when read
CPU: 0 PID: 7 Comm: kworker/0:0 Not tainted 6.4.0-rc3
PC is at _of_add_opp_table_v2 (include/linux/of.h:949
drivers/opp/of.c:98 drivers/opp/of.c:344 drivers/opp/of.c:404
drivers/opp/of.c:1032) -> lazy_link_required_opp_table()
Fix this by calling _of_clear_opp_table() to remove the opp_table from
the list and clear other allocated resources. While at it, also add the
missing mutex_destroy() calls in the error path. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: core: Prevent invalid memory access when there is no parent
Commit 813665564b3d ("iio: core: Convert to use firmware node handle
instead of OF node") switched the kind of nodes to use for label
retrieval in device registration. Probably an unwanted change in that
commit was that if the device has no parent then NULL pointer is
accessed. This is what happens in the stock IIO dummy driver when a
new entry is created in configfs:
# mkdir /sys/kernel/config/iio/devices/dummy/foo
BUG: kernel NULL pointer dereference, address: ...
...
Call Trace:
__iio_device_register
iio_dummy_probe
Since there seems to be no reason to make a parent device of an IIO
dummy device mandatory, let’s prevent the invalid memory access in
__iio_device_register when the parent device is NULL. With this
change, the IIO dummy driver works fine with configfs. |
