| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: Fix potential NULL pointer dereference in header processing
If siw_get_hdr() returns -EINVAL before set_rx_fpdu_context(),
qp->rx_fpdu can be NULL. The error path in siw_tcp_rx_data()
dereferences qp->rx_fpdu->more_ddp_segs without checking, which
may lead to a NULL pointer deref. Only check more_ddp_segs when
rx_fpdu is present.
KASAN splat:
[ 101.384271] KASAN: null-ptr-deref in range [0x00000000000000c0-0x00000000000000c7]
[ 101.385869] RIP: 0010:siw_tcp_rx_data+0x13ad/0x1e50 |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix DMA FIFO desync on error CQE SQ recovery
In case of a TX error CQE, a recovery flow is triggered,
mlx5e_reset_txqsq_cc_pc() resets dma_fifo_cc to 0 but not dma_fifo_pc,
desyncing the DMA FIFO producer and consumer.
After recovery, the producer pushes new DMA entries at the old
dma_fifo_pc, while the consumer reads from position 0.
This causes us to unmap stale DMA addresses from before the recovery.
The DMA FIFO is a purely software construct with no HW counterpart.
At the point of reset, all WQEs have been flushed so dma_fifo_cc is
already equal to dma_fifo_pc. There is no need to reset either counter,
similar to how skb_fifo pc/cc are untouched.
Remove the 'dma_fifo_cc = 0' reset.
This fixes the following WARNING:
WARNING: CPU: 0 PID: 0 at drivers/iommu/dma-iommu.c:1240 iommu_dma_unmap_page+0x79/0x90
Modules linked in: mlx5_vdpa vringh vdpa bonding mlx5_ib mlx5_vfio_pci ipip mlx5_fwctl tunnel4 mlx5_core ib_ipoib geneve ip6_gre ip_gre gre nf_tables ip6_tunnel rdma_ucm ib_uverbs ib_umad vfio_pci vfio_pci_core act_mirred act_skbedit act_vlan vhost_net vhost tap ip6table_mangle ip6table_nat ip6table_filter ip6_tables iptable_mangle cls_matchall nfnetlink_cttimeout act_gact cls_flower sch_ingress vhost_iotlb iptable_raw tunnel6 vfio_iommu_type1 vfio openvswitch nsh rpcsec_gss_krb5 auth_rpcgss oid_registry xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat nf_nat xt_addrtype br_netfilter overlay zram zsmalloc rpcrdma ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_cm ib_core fuse [last unloaded: nf_tables]
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.13.0-rc5_for_upstream_min_debug_2024_12_30_21_33 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:iommu_dma_unmap_page+0x79/0x90
Code: 2b 4d 3b 21 72 26 4d 3b 61 08 73 20 49 89 d8 44 89 f9 5b 4c 89 f2 4c 89 e6 48 89 ef 5d 41 5c 41 5d 41 5e 41 5f e9 c7 ae 9e ff <0f> 0b 5b 5d 41 5c 41 5d 41 5e 41 5f c3 66 2e 0f 1f 84 00 00 00 00
Call Trace:
<IRQ>
? __warn+0x7d/0x110
? iommu_dma_unmap_page+0x79/0x90
? report_bug+0x16d/0x180
? handle_bug+0x4f/0x90
? exc_invalid_op+0x14/0x70
? asm_exc_invalid_op+0x16/0x20
? iommu_dma_unmap_page+0x79/0x90
? iommu_dma_unmap_page+0x2e/0x90
dma_unmap_page_attrs+0x10d/0x1b0
mlx5e_tx_wi_dma_unmap+0xbe/0x120 [mlx5_core]
mlx5e_poll_tx_cq+0x16d/0x690 [mlx5_core]
mlx5e_napi_poll+0x8b/0xac0 [mlx5_core]
__napi_poll+0x24/0x190
net_rx_action+0x32a/0x3b0
? mlx5_eq_comp_int+0x7e/0x270 [mlx5_core]
? notifier_call_chain+0x35/0xa0
handle_softirqs+0xc9/0x270
irq_exit_rcu+0x71/0xd0
common_interrupt+0x7f/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40 |
| In the Linux kernel, the following vulnerability has been resolved:
fs: ntfs3: check return value of indx_find to avoid infinite loop
We found an infinite loop bug in the ntfs3 file system that can lead to a
Denial-of-Service (DoS) condition.
A malformed dentry in the ntfs3 filesystem can cause the kernel to hang
during the lookup operations. By setting the HAS_SUB_NODE flag in an
INDEX_ENTRY within a directory's INDEX_ALLOCATION block and manipulating the
VCN pointer, an attacker can cause the indx_find() function to repeatedly
read the same block, allocating 4 KB of memory each time. The kernel lacks
VCN loop detection and depth limits, causing memory exhaustion and an OOM
crash.
This patch adds a return value check for fnd_push() to prevent a memory
exhaustion vulnerability caused by infinite loops. When the index exceeds the
size of the fnd->nodes array, fnd_push() returns -EINVAL. The indx_find()
function checks this return value and stops processing, preventing further
memory allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix crash when moving to switchdev mode
When moving to switchdev mode when the device doesn't support IPsec,
we try to clean up the IPsec resources anyway which causes the crash
below, fix that by correctly checking for IPsec support before trying
to clean up its resources.
[27642.515799] WARNING: arch/x86/mm/fault.c:1276 at
do_user_addr_fault+0x18a/0x680, CPU#4: devlink/6490
[27642.517159] Modules linked in: xt_conntrack xt_MASQUERADE
ip6table_nat ip6table_filter ip6_tables iptable_nat nf_nat xt_addrtype
rpcsec_gss_krb5 auth_rpcgss oid_registry overlay mlx5_fwctl nfnetlink
zram zsmalloc mlx5_ib fuse rpcrdma rdma_ucm ib_uverbs ib_iser libiscsi
scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_core
ib_core
[27642.521358] CPU: 4 UID: 0 PID: 6490 Comm: devlink Not tainted
6.19.0-rc5_for_upstream_min_debug_2026_01_14_16_47 #1 NONE
[27642.522923] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[27642.524528] RIP: 0010:do_user_addr_fault+0x18a/0x680
[27642.525362] Code: ff 0f 84 75 03 00 00 48 89 ee 4c 89 e7 e8 5e b9 22
00 49 89 c0 48 85 c0 0f 84 a8 02 00 00 f7 c3 60 80 00 00 74 22 31 c9 eb
ae <0f> 0b 48 83 c4 10 48 89 ea 48 89 de 4c 89 f7 5b 5d 41 5c 41 5d
41
[27642.528166] RSP: 0018:ffff88810770f6b8 EFLAGS: 00010046
[27642.529038] RAX: 0000000000000000 RBX: 0000000000000002 RCX:
ffff88810b980f00
[27642.530158] RDX: 00000000000000a0 RSI: 0000000000000002 RDI:
ffff88810770f728
[27642.531270] RBP: 00000000000000a0 R08: 0000000000000000 R09:
0000000000000000
[27642.532383] R10: 0000000000000000 R11: 0000000000000000 R12:
ffff888103f3c4c0
[27642.533499] R13: 0000000000000000 R14: ffff88810770f728 R15:
0000000000000000
[27642.534614] FS: 00007f197c741740(0000) GS:ffff88856a94c000(0000)
knlGS:0000000000000000
[27642.535915] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[27642.536858] CR2: 00000000000000a0 CR3: 000000011334c003 CR4:
0000000000172eb0
[27642.537982] Call Trace:
[27642.538466] <TASK>
[27642.538907] exc_page_fault+0x76/0x140
[27642.539583] asm_exc_page_fault+0x22/0x30
[27642.540282] RIP: 0010:_raw_spin_lock_irqsave+0x10/0x30
[27642.541134] Code: 07 85 c0 75 11 ba ff 00 00 00 f0 0f b1 17 75 06 b8
01 00 00 00 c3 31 c0 c3 90 0f 1f 44 00 00 53 9c 5b fa 31 c0 ba 01 00 00
00 <f0> 0f b1 17 75 05 48 89 d8 5b c3 89 c6 e8 7e 02 00 00 48 89 d8
5b
[27642.543936] RSP: 0018:ffff88810770f7d8 EFLAGS: 00010046
[27642.544803] RAX: 0000000000000000 RBX: 0000000000000202 RCX:
ffff888113ad96d8
[27642.545916] RDX: 0000000000000001 RSI: ffff88810770f818 RDI:
00000000000000a0
[27642.547027] RBP: 0000000000000098 R08: 0000000000000400 R09:
ffff88810b980f00
[27642.548140] R10: 0000000000000001 R11: ffff888101845a80 R12:
00000000000000a8
[27642.549263] R13: ffffffffa02a9060 R14: 00000000000000a0 R15:
ffff8881130d8a40
[27642.550379] complete_all+0x20/0x90
[27642.551010] mlx5e_ipsec_disable_events+0xb6/0xf0 [mlx5_core]
[27642.552022] mlx5e_nic_disable+0x12d/0x220 [mlx5_core]
[27642.552929] mlx5e_detach_netdev+0x66/0xf0 [mlx5_core]
[27642.553822] mlx5e_netdev_change_profile+0x5b/0x120 [mlx5_core]
[27642.554821] mlx5e_vport_rep_load+0x419/0x590 [mlx5_core]
[27642.555757] ? xa_load+0x53/0x90
[27642.556361] __esw_offloads_load_rep+0x54/0x70 [mlx5_core]
[27642.557328] mlx5_esw_offloads_rep_load+0x45/0xd0 [mlx5_core]
[27642.558320] esw_offloads_enable+0xb4b/0xc90 [mlx5_core]
[27642.559247] mlx5_eswitch_enable_locked+0x34e/0x4f0 [mlx5_core]
[27642.560257] ? mlx5_rescan_drivers_locked+0x222/0x2d0 [mlx5_core]
[27642.561284] mlx5_devlink_eswitch_mode_set+0x5ac/0x9c0 [mlx5_core]
[27642.562334] ? devlink_rate_set_ops_supported+0x21/0x3a0
[27642.563220] devlink_nl_eswitch_set_doit+0x67/0xe0
[27642.564026] genl_family_rcv_msg_doit+0xe0/0x130
[27642.564816] genl_rcv_msg+0x183/0x290
[27642.565466] ? __devlink_nl_pre_doit.isra.0+0x160/0x160
[27642.566329] ? d
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
X.509: Fix out-of-bounds access when parsing extensions
Leo reports an out-of-bounds access when parsing a certificate with
empty Basic Constraints or Key Usage extension because the first byte of
the extension is read before checking its length. Fix it.
The bug can be triggered by an unprivileged user by submitting a
specially crafted certificate to the kernel through the keyrings(7) API.
Leo has demonstrated this with a proof-of-concept program responsibly
disclosed off-list. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix deadlock between devlink lock and esw->wq
esw->work_queue executes esw_functions_changed_event_handler ->
esw_vfs_changed_event_handler and acquires the devlink lock.
.eswitch_mode_set (acquires devlink lock in devlink_nl_pre_doit) ->
mlx5_devlink_eswitch_mode_set -> mlx5_eswitch_disable_locked ->
mlx5_eswitch_event_handler_unregister -> flush_workqueue deadlocks
when esw_vfs_changed_event_handler executes.
Fix that by no longer flushing the work to avoid the deadlock, and using
a generation counter to keep track of work relevance. This avoids an old
handler manipulating an esw that has undergone one or more mode changes:
- the counter is incremented in mlx5_eswitch_event_handler_unregister.
- the counter is read and passed to the ephemeral mlx5_host_work struct.
- the work handler takes the devlink lock and bails out if the current
generation is different than the one it was scheduled to operate on.
- mlx5_eswitch_cleanup does the final draining before destroying the wq.
No longer flushing the workqueue has the side effect of maybe no longer
cancelling pending vport_change_handler work items, but that's ok since
those are disabled elsewhere:
- mlx5_eswitch_disable_locked disables the vport eq notifier.
- mlx5_esw_vport_disable disarms the HW EQ notification and marks
vport->enabled under state_lock to false to prevent pending vport
handler from doing anything.
- mlx5_eswitch_cleanup destroys the workqueue and makes sure all events
are disabled/finished. |
| In the Linux kernel, the following vulnerability has been resolved:
unshare: fix unshare_fs() handling
There's an unpleasant corner case in unshare(2), when we have a
CLONE_NEWNS in flags and current->fs hadn't been shared at all; in that
case copy_mnt_ns() gets passed current->fs instead of a private copy,
which causes interesting warts in proof of correctness]
> I guess if private means fs->users == 1, the condition could still be true.
Unfortunately, it's worse than just a convoluted proof of correctness.
Consider the case when we have CLONE_NEWCGROUP in addition to CLONE_NEWNS
(and current->fs->users == 1).
We pass current->fs to copy_mnt_ns(), all right. Suppose it succeeds and
flips current->fs->{pwd,root} to corresponding locations in the new namespace.
Now we proceed to copy_cgroup_ns(), which fails (e.g. with -ENOMEM).
We call put_mnt_ns() on the namespace created by copy_mnt_ns(), it's
destroyed and its mount tree is dissolved, but... current->fs->root and
current->fs->pwd are both left pointing to now detached mounts.
They are pinning those, so it's not a UAF, but it leaves the calling
process with unshare(2) failing with -ENOMEM _and_ leaving it with
pwd and root on detached isolated mounts. The last part is clearly a bug.
There is other fun related to that mess (races with pivot_root(), including
the one between pivot_root() and fork(), of all things), but this one
is easy to isolate and fix - treat CLONE_NEWNS as "allocate a new
fs_struct even if it hadn't been shared in the first place". Sure, we could
go for something like "if both CLONE_NEWNS *and* one of the things that might
end up failing after copy_mnt_ns() call in create_new_namespaces() are set,
force allocation of new fs_struct", but let's keep it simple - the cost
of copy_fs_struct() is trivial.
Another benefit is that copy_mnt_ns() with CLONE_NEWNS *always* gets
a freshly allocated fs_struct, yet to be attached to anything. That
seriously simplifies the analysis...
FWIW, that bug had been there since the introduction of unshare(2) ;-/ |
| In the Linux kernel, the following vulnerability has been resolved:
fs: init flags_valid before calling vfs_fileattr_get
syzbot reported a uninit-value bug in [1].
Similar to the "*get" context where the kernel's internal file_kattr
structure is initialized before calling vfs_fileattr_get(), we should
use the same mechanism when using fa.
[1]
BUG: KMSAN: uninit-value in fuse_fileattr_get+0xeb4/0x1450 fs/fuse/ioctl.c:517
fuse_fileattr_get+0xeb4/0x1450 fs/fuse/ioctl.c:517
vfs_fileattr_get fs/file_attr.c:94 [inline]
__do_sys_file_getattr fs/file_attr.c:416 [inline]
Local variable fa.i created at:
__do_sys_file_getattr fs/file_attr.c:380 [inline]
__se_sys_file_getattr+0x8c/0xbd0 fs/file_attr.c:372 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: storvsc: Fix scheduling while atomic on PREEMPT_RT
This resolves the follow splat and lock-up when running with PREEMPT_RT
enabled on Hyper-V:
[ 415.140818] BUG: scheduling while atomic: stress-ng-iomix/1048/0x00000002
[ 415.140822] INFO: lockdep is turned off.
[ 415.140823] Modules linked in: intel_rapl_msr intel_rapl_common intel_uncore_frequency_common intel_pmc_core pmt_telemetry pmt_discovery pmt_class intel_pmc_ssram_telemetry intel_vsec ghash_clmulni_intel aesni_intel rapl binfmt_misc nls_ascii nls_cp437 vfat fat snd_pcm hyperv_drm snd_timer drm_client_lib drm_shmem_helper snd sg soundcore drm_kms_helper pcspkr hv_balloon hv_utils evdev joydev drm configfs efi_pstore nfnetlink vsock_loopback vmw_vsock_virtio_transport_common hv_sock vmw_vsock_vmci_transport vsock vmw_vmci efivarfs autofs4 ext4 crc16 mbcache jbd2 sr_mod sd_mod cdrom hv_storvsc serio_raw hid_generic scsi_transport_fc hid_hyperv scsi_mod hid hv_netvsc hyperv_keyboard scsi_common
[ 415.140846] Preemption disabled at:
[ 415.140847] [<ffffffffc0656171>] storvsc_queuecommand+0x2e1/0xbe0 [hv_storvsc]
[ 415.140854] CPU: 8 UID: 0 PID: 1048 Comm: stress-ng-iomix Not tainted 6.19.0-rc7 #30 PREEMPT_{RT,(full)}
[ 415.140856] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 09/04/2024
[ 415.140857] Call Trace:
[ 415.140861] <TASK>
[ 415.140861] ? storvsc_queuecommand+0x2e1/0xbe0 [hv_storvsc]
[ 415.140863] dump_stack_lvl+0x91/0xb0
[ 415.140870] __schedule_bug+0x9c/0xc0
[ 415.140875] __schedule+0xdf6/0x1300
[ 415.140877] ? rtlock_slowlock_locked+0x56c/0x1980
[ 415.140879] ? rcu_is_watching+0x12/0x60
[ 415.140883] schedule_rtlock+0x21/0x40
[ 415.140885] rtlock_slowlock_locked+0x502/0x1980
[ 415.140891] rt_spin_lock+0x89/0x1e0
[ 415.140893] hv_ringbuffer_write+0x87/0x2a0
[ 415.140899] vmbus_sendpacket_mpb_desc+0xb6/0xe0
[ 415.140900] ? rcu_is_watching+0x12/0x60
[ 415.140902] storvsc_queuecommand+0x669/0xbe0 [hv_storvsc]
[ 415.140904] ? HARDIRQ_verbose+0x10/0x10
[ 415.140908] ? __rq_qos_issue+0x28/0x40
[ 415.140911] scsi_queue_rq+0x760/0xd80 [scsi_mod]
[ 415.140926] __blk_mq_issue_directly+0x4a/0xc0
[ 415.140928] blk_mq_issue_direct+0x87/0x2b0
[ 415.140931] blk_mq_dispatch_queue_requests+0x120/0x440
[ 415.140933] blk_mq_flush_plug_list+0x7a/0x1a0
[ 415.140935] __blk_flush_plug+0xf4/0x150
[ 415.140940] __submit_bio+0x2b2/0x5c0
[ 415.140944] ? submit_bio_noacct_nocheck+0x272/0x360
[ 415.140946] submit_bio_noacct_nocheck+0x272/0x360
[ 415.140951] ext4_read_bh_lock+0x3e/0x60 [ext4]
[ 415.140995] ext4_block_write_begin+0x396/0x650 [ext4]
[ 415.141018] ? __pfx_ext4_da_get_block_prep+0x10/0x10 [ext4]
[ 415.141038] ext4_da_write_begin+0x1c4/0x350 [ext4]
[ 415.141060] generic_perform_write+0x14e/0x2c0
[ 415.141065] ext4_buffered_write_iter+0x6b/0x120 [ext4]
[ 415.141083] vfs_write+0x2ca/0x570
[ 415.141087] ksys_write+0x76/0xf0
[ 415.141089] do_syscall_64+0x99/0x1490
[ 415.141093] ? rcu_is_watching+0x12/0x60
[ 415.141095] ? finish_task_switch.isra.0+0xdf/0x3d0
[ 415.141097] ? rcu_is_watching+0x12/0x60
[ 415.141098] ? lock_release+0x1f0/0x2a0
[ 415.141100] ? rcu_is_watching+0x12/0x60
[ 415.141101] ? finish_task_switch.isra.0+0xe4/0x3d0
[ 415.141103] ? rcu_is_watching+0x12/0x60
[ 415.141104] ? __schedule+0xb34/0x1300
[ 415.141106] ? hrtimer_try_to_cancel+0x1d/0x170
[ 415.141109] ? do_nanosleep+0x8b/0x160
[ 415.141111] ? hrtimer_nanosleep+0x89/0x100
[ 415.141114] ? __pfx_hrtimer_wakeup+0x10/0x10
[ 415.141116] ? xfd_validate_state+0x26/0x90
[ 415.141118] ? rcu_is_watching+0x12/0x60
[ 415.141120] ? do_syscall_64+0x1e0/0x1490
[ 415.141121] ? do_syscall_64+0x1e0/0x1490
[ 415.141123] ? rcu_is_watching+0x12/0x60
[ 415.141124] ? do_syscall_64+0x1e0/0x1490
[ 415.141125] ? do_syscall_64+0x1e0/0x1490
[ 415.141127] ? irqentry_exit+0x140/0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
xprtrdma: Decrement re_receiving on the early exit paths
In the event that rpcrdma_post_recvs() fails to create a work request
(due to memory allocation failure, say) or otherwise exits early, we
should decrement ep->re_receiving before returning. Otherwise we will
hang in rpcrdma_xprt_drain() as re_receiving will never reach zero and
the completion will never be triggered.
On a system with high memory pressure, this can appear as the following
hung task:
INFO: task kworker/u385:17:8393 blocked for more than 122 seconds.
Tainted: G S E 6.19.0 #3
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u385:17 state:D stack:0 pid:8393 tgid:8393 ppid:2 task_flags:0x4248060 flags:0x00080000
Workqueue: xprtiod xprt_autoclose [sunrpc]
Call Trace:
<TASK>
__schedule+0x48b/0x18b0
? ib_post_send_mad+0x247/0xae0 [ib_core]
schedule+0x27/0xf0
schedule_timeout+0x104/0x110
__wait_for_common+0x98/0x180
? __pfx_schedule_timeout+0x10/0x10
wait_for_completion+0x24/0x40
rpcrdma_xprt_disconnect+0x444/0x460 [rpcrdma]
xprt_rdma_close+0x12/0x40 [rpcrdma]
xprt_autoclose+0x5f/0x120 [sunrpc]
process_one_work+0x191/0x3e0
worker_thread+0x2e3/0x420
? __pfx_worker_thread+0x10/0x10
kthread+0x10d/0x230
? __pfx_kthread+0x10/0x10
ret_from_fork+0x273/0x2b0
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_red: Replace direct dequeue call with peek and qdisc_dequeue_peeked
When red qdisc has children (eg qfq qdisc) whose peek() callback is
qdisc_peek_dequeued(), we could get a kernel panic. When the parent of such
qdiscs (eg illustrated in patch #3 as tbf) wants to retrieve an skb from
its child (red in this case), it will do the following:
1a. do a peek() - and when sensing there's an skb the child can offer, then
- the child in this case(red) calls its child's (qfq) peek.
qfq does the right thing and will return the gso_skb queue packet.
Note: if there wasnt a gso_skb entry then qfq will store it there.
1b. invoke a dequeue() on the child (red). And herein lies the problem.
- red will call the child's dequeue() which will essentially just
try to grab something of qfq's queue.
[ 78.667668][ T363] KASAN: null-ptr-deref in range [0x0000000000000048-0x000000000000004f]
[ 78.667927][ T363] CPU: 1 UID: 0 PID: 363 Comm: ping Not tainted 7.1.0-rc1-00033-g46f74a3f7d57-dirty #790 PREEMPT(full)
[ 78.668263][ T363] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 78.668486][ T363] RIP: 0010:qfq_dequeue+0x446/0xc90 [sch_qfq]
[ 78.668718][ T363] Code: 54 c0 e8 dd 90 00 f1 48 c7 c7 e0 03 54 c0 48 89 de e8 ce 90 00 f1 48 8d 7b 48 b8 ff ff 37 00 48 89 fa 48 c1 e0 2a 48 c1 ea 03 <80> 3c 02 00 74 05 e8 ef a1 e1 f1 48 8b 7b 48 48 8d 54 24 58 48 8d
[ 78.669312][ T363] RSP: 0018:ffff88810de573e0 EFLAGS: 00010216
[ 78.669533][ T363] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 78.669790][ T363] RDX: 0000000000000009 RSI: 0000000000000004 RDI: 0000000000000048
[ 78.670044][ T363] RBP: ffff888110dc4000 R08: ffffffffb1b0885a R09: fffffbfff6ba9078
[ 78.670297][ T363] R10: 0000000000000003 R11: ffff888110e31c80 R12: 0000001880000000
[ 78.670560][ T363] R13: ffff888110dc4150 R14: ffff888110dc42b8 R15: 0000000000000200
[ 78.670814][ T363] FS: 00007f66a8f09c40(0000) GS:ffff888163428000(0000) knlGS:0000000000000000
[ 78.671110][ T363] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 78.671324][ T363] CR2: 000055db4c6a30a8 CR3: 000000010da67000 CR4: 0000000000750ef0
[ 78.671585][ T363] PKRU: 55555554
[ 78.671713][ T363] Call Trace:
[ 78.671843][ T363] <TASK>
[ 78.671936][ T363] ? __pfx_qfq_dequeue+0x10/0x10 [sch_qfq]
[ 78.672148][ T363] ? __pfx__printk+0x10/0x10
[ 78.672322][ T363] ? srso_alias_return_thunk+0x5/0xfbef5
[ 78.672496][ T363] ? lockdep_hardirqs_on_prepare+0xa8/0x1a0
[ 78.672706][ T363] ? srso_alias_return_thunk+0x5/0xfbef5
[ 78.672875][ T363] ? trace_hardirqs_on+0x19/0x1a0
[ 78.673047][ T363] red_dequeue+0x65/0x270 [sch_red]
[ 78.673217][ T363] ? srso_alias_return_thunk+0x5/0xfbef5
[ 78.673385][ T363] tbf_dequeue.cold+0xb0/0x70c [sch_tbf]
[ 78.673566][ T363] __qdisc_run+0x169/0x1900
The right thing to do in #1b is to grab the skb off gso_skb queue.
This patchset fixes that issue by changing #1b to use qdisc_dequeue_peeked()
method instead. |
| In the Linux kernel, the following vulnerability has been resolved:
nfs: return EISDIR on nfs3_proc_create if d_alias is a dir
If we found an alias through nfs3_do_create/nfs_add_or_obtain
/d_splice_alias which happens to be a dir dentry, we don't return
any error, and simply forget about this alias, but the original
dentry we were adding and passed as parameter remains negative.
This later causes an oops on nfs_atomic_open_v23/finish_open since we
supply a negative dentry to do_dentry_open.
This has been observed running lustre-racer, where dirs and files are
created/removed concurrently with the same name and O_EXCL is not
used to open files (frequent file redirection).
While d_splice_alias typically returns a directory alias or NULL, we
explicitly check d_is_dir() to ensure that we don't attempt to perform
file operations (like finish_open) on a directory inode, which triggers
the observed oops. |
| In the Linux kernel, the following vulnerability has been resolved:
net: liquidio: Fix off-by-one error in PF setup_nic_devices() cleanup
In setup_nic_devices(), the initialization loop jumps to the label
setup_nic_dev_free on failure. The current cleanup loop while(i--)
skip the failing index i, causing a memory leak.
Fix this by changing the loop to iterate from the current index i
down to 0.
Also, decrement i in the devlink_alloc failure path to point to the
last successfully allocated index.
Compile tested only. Issue found using code review. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: cdc_ncm: add ndpoffset to NDP16 nframes bounds check
cdc_ncm_rx_verify_ndp16() validates that the NDP header and its DPE
entries fit within the skb. The first check correctly accounts for
ndpoffset:
if ((ndpoffset + sizeof(struct usb_cdc_ncm_ndp16)) > skb_in->len)
but the second check omits it:
if ((sizeof(struct usb_cdc_ncm_ndp16) +
ret * (sizeof(struct usb_cdc_ncm_dpe16))) > skb_in->len)
This validates the DPE array size against the total skb length as if
the NDP were at offset 0, rather than at ndpoffset. When the NDP is
placed near the end of the NTB (large wNdpIndex), the DPE entries can
extend past the skb data buffer even though the check passes.
cdc_ncm_rx_fixup() then reads out-of-bounds memory when iterating
the DPE array.
Add ndpoffset to the nframes bounds check and use struct_size_t() to
express the NDP-plus-DPE-array size more clearly. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: teql: Fix double-free in teql_master_xmit
Whenever a TEQL devices has a lockless Qdisc as root, qdisc_reset should
be called using the seq_lock to avoid racing with the datapath. Failure
to do so may cause crashes like the following:
[ 238.028993][ T318] BUG: KASAN: double-free in skb_release_data (net/core/skbuff.c:1139)
[ 238.029328][ T318] Free of addr ffff88810c67ec00 by task poc_teql_uaf_ke/318
[ 238.029749][ T318]
[ 238.029900][ T318] CPU: 3 UID: 0 PID: 318 Comm: poc_teql_ke Not tainted 7.0.0-rc3-00149-ge5b31d988a41 #704 PREEMPT(full)
[ 238.029906][ T318] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 238.029910][ T318] Call Trace:
[ 238.029913][ T318] <TASK>
[ 238.029916][ T318] dump_stack_lvl (lib/dump_stack.c:122)
[ 238.029928][ T318] print_report (mm/kasan/report.c:379 mm/kasan/report.c:482)
[ 238.029940][ T318] ? skb_release_data (net/core/skbuff.c:1139)
[ 238.029944][ T318] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
...
[ 238.029957][ T318] ? skb_release_data (net/core/skbuff.c:1139)
[ 238.029969][ T318] kasan_report_invalid_free (mm/kasan/report.c:221 mm/kasan/report.c:563)
[ 238.029979][ T318] ? skb_release_data (net/core/skbuff.c:1139)
[ 238.029989][ T318] check_slab_allocation (mm/kasan/common.c:231)
[ 238.029995][ T318] kmem_cache_free (mm/slub.c:2637 (discriminator 1) mm/slub.c:6168 (discriminator 1) mm/slub.c:6298 (discriminator 1))
[ 238.030004][ T318] skb_release_data (net/core/skbuff.c:1139)
...
[ 238.030025][ T318] sk_skb_reason_drop (net/core/skbuff.c:1256)
[ 238.030032][ T318] pfifo_fast_reset (./include/linux/ptr_ring.h:171 ./include/linux/ptr_ring.h:309 ./include/linux/skb_array.h:98 net/sched/sch_generic.c:827)
[ 238.030039][ T318] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
...
[ 238.030054][ T318] qdisc_reset (net/sched/sch_generic.c:1034)
[ 238.030062][ T318] teql_destroy (./include/linux/spinlock.h:395 net/sched/sch_teql.c:157)
[ 238.030071][ T318] __qdisc_destroy (./include/net/pkt_sched.h:328 net/sched/sch_generic.c:1077)
[ 238.030077][ T318] qdisc_graft (net/sched/sch_api.c:1062 net/sched/sch_api.c:1053 net/sched/sch_api.c:1159)
[ 238.030089][ T318] ? __pfx_qdisc_graft (net/sched/sch_api.c:1091)
[ 238.030095][ T318] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
[ 238.030102][ T318] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
[ 238.030106][ T318] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
[ 238.030114][ T318] tc_get_qdisc (net/sched/sch_api.c:1529 net/sched/sch_api.c:1556)
...
[ 238.072958][ T318] Allocated by task 303 on cpu 5 at 238.026275s:
[ 238.073392][ T318] kasan_save_stack (mm/kasan/common.c:58)
[ 238.073884][ T318] kasan_save_track (mm/kasan/common.c:64 (discriminator 5) mm/kasan/common.c:79 (discriminator 5))
[ 238.074230][ T318] __kasan_slab_alloc (mm/kasan/common.c:369)
[ 238.074578][ T318] kmem_cache_alloc_node_noprof (./include/linux/kasan.h:253 mm/slub.c:4542 mm/slub.c:4869 mm/slub.c:4921)
[ 238.076091][ T318] kmalloc_reserve (net/core/skbuff.c:616 (discriminator 107))
[ 238.076450][ T318] __alloc_skb (net/core/skbuff.c:713)
[ 238.076834][ T318] alloc_skb_with_frags (./include/linux/skbuff.h:1383 net/core/skbuff.c:6763)
[ 238.077178][ T318] sock_alloc_send_pskb (net/core/sock.c:2997)
[ 238.077520][ T318] packet_sendmsg (net/packet/af_packet.c:2926 net/packet/af_packet.c:3019 net/packet/af_packet.c:3108)
[ 238.081469][ T318]
[ 238.081870][ T318] Freed by task 299 on cpu 1 at 238.028496s:
[ 238.082761][ T318] kasan_save_stack (mm/kasan/common.c:58)
[ 238.083481][ T318] kasan_save_track (mm/kasan/common.c:64 (discriminator 5) mm/kasan/common.c:79 (discriminator 5))
[ 238.085348][ T318] kasan_save_free_info (mm/kasan/generic.c:587 (discriminator 1))
[ 238.085900][ T318] __kasan_slab_free (mm/
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix NULL dereference and UAF in smc_tcp_syn_recv_sock()
Syzkaller reported a panic in smc_tcp_syn_recv_sock() [1].
smc_tcp_syn_recv_sock() is called in the TCP receive path
(softirq) via icsk_af_ops->syn_recv_sock on the clcsock (TCP
listening socket). It reads sk_user_data to get the smc_sock
pointer. However, when the SMC listen socket is being closed
concurrently, smc_close_active() sets clcsock->sk_user_data
to NULL under sk_callback_lock, and then the smc_sock itself
can be freed via sock_put() in smc_release().
This leads to two issues:
1) NULL pointer dereference: sk_user_data is NULL when
accessed.
2) Use-after-free: sk_user_data is read as non-NULL, but the
smc_sock is freed before its fields (e.g., queued_smc_hs,
ori_af_ops) are accessed.
The race window looks like this (the syzkaller crash [1]
triggers via the SYN cookie path: tcp_get_cookie_sock() ->
smc_tcp_syn_recv_sock(), but the normal tcp_check_req() path
has the same race):
CPU A (softirq) CPU B (process ctx)
tcp_v4_rcv()
TCP_NEW_SYN_RECV:
sk = req->rsk_listener
sock_hold(sk)
/* No lock on listener */
smc_close_active():
write_lock_bh(cb_lock)
sk_user_data = NULL
write_unlock_bh(cb_lock)
...
smc_clcsock_release()
sock_put(smc->sk) x2
-> smc_sock freed!
tcp_check_req()
smc_tcp_syn_recv_sock():
smc = user_data(sk)
-> NULL or dangling
smc->queued_smc_hs
-> crash!
Note that the clcsock and smc_sock are two independent objects
with separate refcounts. TCP stack holds a reference on the
clcsock, which keeps it alive, but this does NOT prevent the
smc_sock from being freed.
Fix this by using RCU and refcount_inc_not_zero() to safely
access smc_sock. Since smc_tcp_syn_recv_sock() is called in
the TCP three-way handshake path, taking read_lock_bh on
sk_callback_lock is too heavy and would not survive a SYN
flood attack. Using rcu_read_lock() is much more lightweight.
- Set SOCK_RCU_FREE on the SMC listen socket so that
smc_sock freeing is deferred until after the RCU grace
period. This guarantees the memory is still valid when
accessed inside rcu_read_lock().
- Use rcu_read_lock() to protect reading sk_user_data.
- Use refcount_inc_not_zero(&smc->sk.sk_refcnt) to pin the
smc_sock. If the refcount has already reached zero (close
path completed), it returns false and we bail out safely.
Note: smc_hs_congested() has a similar lockless read of
sk_user_data without rcu_read_lock(), but it only checks for
NULL and accesses the global smc_hs_wq, never dereferencing
any smc_sock field, so it is not affected.
Reproducer was verified with mdelay injection and smc_run,
the issue no longer occurs with this patch applied.
[1] https://syzkaller.appspot.com/bug?extid=827ae2bfb3a3529333e9 |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: prevent potential infinite loop in bond_header_parse()
bond_header_parse() can loop if a stack of two bonding devices is setup,
because skb->dev always points to the hierarchy top.
Add new "const struct net_device *dev" parameter to
(struct header_ops)->parse() method to make sure the recursion
is bounded, and that the final leaf parse method is called. |
| In the Linux kernel, the following vulnerability has been resolved:
audit: add missing syscalls to read class
The "at" variant of getxattr() and listxattr() are missing from the
audit read class. Calling getxattrat() or listxattrat() on a file to
read its extended attributes will bypass audit rules such as:
-w /tmp/test -p rwa -k test_rwa
The current patch adds missing syscalls to the audit read class. |
| In the Linux kernel, the following vulnerability has been resolved:
net: add proper RCU protection to /proc/net/ptype
Yin Fengwei reported an RCU stall in ptype_seq_show() and provided
a patch.
Real issue is that ptype_seq_next() and ptype_seq_show() violate
RCU rules.
ptype_seq_show() runs under rcu_read_lock(), and reads pt->dev
to get device name without any barrier.
At the same time, concurrent writers can remove a packet_type structure
(which is correctly freed after an RCU grace period) and clear pt->dev
without an RCU grace period.
Define ptype_iter_state to carry a dev pointer along seq_net_private:
struct ptype_iter_state {
struct seq_net_private p;
struct net_device *dev; // added in this patch
};
We need to record the device pointer in ptype_get_idx() and
ptype_seq_next() so that ptype_seq_show() is safe against
concurrent pt->dev changes.
We also need to add full RCU protection in ptype_seq_next().
(Missing READ_ONCE() when reading list.next values)
Many thanks to Dong Chenchen for providing a repro. |
| In the Linux kernel, the following vulnerability has been resolved:
net: liquidio: Fix off-by-one error in VF setup_nic_devices() cleanup
In setup_nic_devices(), the initialization loop jumps to the label
setup_nic_dev_free on failure. The current cleanup loop while(i--)
skip the failing index i, causing a memory leak.
Fix this by changing the loop to iterate from the current index i
down to 0.
Compile tested only. Issue found using code review. |
