| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: fix OOB read via signed offset in rsc_table_for_each_entry()
table->offset[i] is a u32 from firmware, but was stored into a signed
int. A crafted offset like 0xFFFFFFF0 becomes -16, placing hdr 16 bytes
before the table buffer. The subsequent avail check was bypassed
because the negative int was promoted to a large size_t in the
expression "table_sz - offset - sizeof(*hdr)", yielding a large positive
avail and letting the out-of-bounds hdr->type read proceed undetected.
Store the offset as u32 and validate it with unsigned comparisons before
any pointer arithmetic. |
| In the Linux kernel, the following vulnerability has been resolved:
fat: release buffer head after rebuilding parent
fat_scan_logstart() leaves the matching directory entry's buffer head in
sinfo.bh for the caller to release, just like fat_scan().
fat_rebuild_parent() uses the directory entry to rebuild the parent inode
for the nostale_ro NFS export path, but does not release sinfo.bh after a
successful scan. Release it once fat_build_inode() has consumed the
directory entry data. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2/cluster: keep heartbeat local node stable
o2nm_node_local_store() handles local=0 by stopping o2net and setting
cl_local_node to O2NM_INVALID_NODE_NUM, but it leaves cl_has_local set.
That stale state makes o2nm_this_node() return 255, blocks a later local=1
attempt with -EBUSY, and can feed 255 to heartbeat users that call
o2nm_this_node() dynamically.
Clearing cl_has_local is required when the local node is reset. But
heartbeat threads can still be running at that point. They pin the local
node config item at startup, yet o2hb_do_disk_heartbeat() and thread
teardown re-read o2nm_this_node() for the local slot and for
o2nm_undepend_this_node(). Once local=0 has cleared the live local-node
state, those dynamic reads return O2NM_MAX_NODES, which is also the
invalid node number 255.
Store the local node number in the heartbeat region when the region
starts. Use that stable node for heartbeat slot writes/checks,
negotiation messages, and the final configfs undepend. Stop the heartbeat
loop when the current local node no longer matches the stored node, and
clear cl_has_local together with cl_local_node in the local=0 path so
nodemanager state matches node removal.
Validation reproduced this kernel report:
KASAN slab-out-of-bounds in o2hb_do_disk_heartbeat+0x372/0xb30
RIP: 0010:memset+0xf/0x20
Read of size 8
Call trace:
dump_stack_lvl+0x66/0xa0
print_report+0xd0/0x630
o2hb_do_disk_heartbeat+0x372/0xb30 (fs/ocfs2/cluster/heartbeat.c:1079)
srso_alias_return_thunk+0x5/0xfbef5
__virt_addr_valid+0x188/0x2f0
kasan_report+0xe4/0x120
o2hb_do_disk_heartbeat+0x5/0xb30 (fs/ocfs2/cluster/heartbeat.c:1079)
o2hb_thread+0x14e/0x770
kthread_affine_node+0x139/0x180
lockdep_hardirqs_on_prepare+0xda/0x190
trace_hardirqs_on+0x18/0x130
kthread+0x19d/0x1e0
ret_from_fork+0x37a/0x4d0
__switch_to+0x2d5/0x6f0
ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
phonet: pep: do not write beyond optlen in getsockopt
pep_getsockopt() clamps the reported length to the caller's buffer with
min_t(), but then stores the value with put_user(val, (int __user *)
optval), which always writes sizeof(int) bytes. A getsockopt() call with
an optlen smaller than sizeof(int) thus reports the clamped length yet
writes a full int, one to three bytes past the user buffer.
Write the value with copy_to_user() bounded by len, so at most optlen
bytes are copied, matching the length reported back to userspace. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: asus: refactor the two workqueues and init sequence
Multiple issues have been found within the hid-asus driver:
- unchecked size in asus_raw_event()
- unclean teardown of asus_probe on failure
- possible use-after-free in asus_probe
- multiple workqueue used for jobs where one was enough
- sleeping calls in atomic context
- packets of incorrect size being sent to the keyboard controller
Join the two workqueues into one reusing the stopping mechanism
of the brightness workqueue, use the joined workqueue to also
move the asus_wmi_send_event() sleeping call away from atomic
context and add a size check in asus_raw_event(). |
| In the Linux kernel, the following vulnerability has been resolved:
dm-integrity: replace forgeable discard filler with a keyed sector marker
The discard-block check in dm_integrity_rw_tag() treats a stored tag
of all 0xf6 bytes (DISCARD_FILLER) as proof a block was discarded and
skips HMAC verification. allow_discards is only accepted in
dm-integrity's standalone mode. An attacker with raw write access to
the backing device, but without the integrity key, can stamp any block
with an all-0xf6 tag and have it served as authentic.
Add a new "allow_discards_keyed" target argument that marks discarded
blocks with a keyed checksum of (salt || sector) instead, computed by
integrity_discard_checksum(). |
| In the Linux kernel, the following vulnerability has been resolved:
tty: clear cdev pointer after cdev_add() failure
tty_cdev_add() drops the cdev reference when cdev_add() fails, but
leaves driver->cdevs[index] pointing to freed memory.
tty_unregister_device() later passes that stale pointer to cdev_del(),
causing a use-after-free.
Clear the slot after dropping the reference. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: amba-pl011: keep console clock enabled for atomic writes
pl011_console_write_atomic() runs from nbcon atomic context, where
sleeping is not allowed. It calls clk_enable(), which takes the common-clk
enable_lock. Under PREEMPT_RT that is a sleeping lock:
clk_enable_lock() first tries spin_trylock_irqsave(), but on contention
falls back to spin_lock_irqsave(). Therefore, an atomic-context printk on
an RT kernel with a clk-backed pl011 can trip:
BUG: sleeping function called from invalid context at spinlock_rt.c:48
__might_resched from rt_spin_lock
rt_spin_lock from clk_enable_lock
clk_enable_lock from clk_enable
clk_enable from pl011_console_write_atomic
... from vprintk_emit
This was found and reproduced on PREEMPT_RT. Arm32 and arm64 DT SoCs are
affected; arm64 SBSA/ACPI has no clk, so clk_enable(NULL) short-circuits
before the lock. In addition, write_atomic() may be invoked from NMI
context and is documented to avoid locking. Removing clk_enable() from
the callback also avoids a potentially unsafe NMI acquisition of the
common-clock enable_lock.
An nbcon atomic-capable console must be printable from any context, so
the clock cannot be gated between writes. Enable the clock while the
console is available for output: use clk_prepare_enable() in
pl011_console_setup(), release it via clk_disable_unprepare() in the
console .exit() callback, and drop the per-write clk_enable()/clk_disable()
pairs from write_atomic() and write_thread().
When printk suspends consoles, drop the reference after
uart_suspend_port() stops console access and restore it before
uart_resume_port() -- but only if suspend actually marked the port
suspended (a wake-capable tty stays running and must keep its clock), and
keep it when console_suspend_enabled is false so no_console_suspend works.
The active power cost of keeping the clock enabled is platform-dependent:
none where the UART clock is a fixed always-on oscillator, real where it
is a gateable clock branch, which then cannot be gated (nor possibly can
its parent clocks) while the console is available for output. When serial
core actually suspends the port, the reference is released so the clock
provider can gate the clock tree. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: generic: free maps on pinctrl_generic_to_map() failure
pinctrl_generic_to_map() parses DT configuration and allocates pinctrl
maps via pinctrl_utils_reserve_map().
If subsequent steps (such as pinctrl_utils_add_map_mux(),
pinctrl_generic_add_group(), pinconf_generic_parse_dt_config(), or
pinctrl_utils_add_map_configs()) return an error, *maps may contain
partially allocated map entries. Returning the error directly without
freeing *maps leaks the allocated mapping memory across all drivers
that rely on pinctrl_generic_to_map().
Fix this by calling pinctrl_utils_free_map() and resetting *maps,
*num_maps, and *num_reserved_maps in the error path of
pinctrl_generic_to_map(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: disconnect on CSA to channel 0
The refactor for the CSA parsing erroneously equates channel
zero and no information present, leading it to ignore a CSA
on an AP that advertises a switch to that (invalid) channel.
This leads to not disconnecting, which we should. For Intel
devices, this can lead to a firmware crash.
Fix this by using an int type for the channel number as well
as the opclass, and using a (negative) value that cannot be
encoded in the element to indicate it's not present. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath10k: snoc: use memcpy_fromio() for MSA ramdump
On WCN3990/SNOC the MSA region is mapped with devm_memremap(MEMREMAP_WT).
On arm64 such a mapping is not Normal-cacheable, so unaligned accesses to
it are not permitted. ath10k_msa_dump_memory() copies the region with a
plain memcpy(), whose optimized __pi_memcpy_generic implementation issues
wide/unaligned loads. This triggers an alignment fault (FSC=0x21) Oops in
ath10k_snoc_fw_crashed_dump() while collecting the devcoredump:
Unable to handle kernel paging request ... FSC=0x21: alignment fault
pc : __pi_memcpy_generic
lr : ath10k_snoc_fw_crashed_dump [ath10k_snoc]
The Oops both leaves the firmware RAM dump buffer zeroed (no dump is
captured) and crashes the kernel, which in turn breaks modem SSR
recovery.
Use memcpy_fromio(), which only performs accesses that are valid for such
a device-memory mapping. The generic memcpy_fromio() implementation aligns
the source before issuing word-sized reads and stores the destination with
put_unaligned(), so it is also safe for the coherent DMA allocation used on
the non-reserved-memory path. ath11k and ath12k use the same pattern
when copying target memory into crash dumps, so call it unconditionally
here too.
The MEMREMAP_WT pointer is a plain void *, so an explicit __iomem cast is
needed; use __force to keep sparse happy.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.3.7.c5-00107-QCAHLSWMTPL-1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: reject out-of-range link ids in mt76_vif_link()
mt76_vif_link() indexes mvif->link[] without validating link_id, but
callers pass mvif->deflink_id / msta->deflink_id, which hold
IEEE80211_LINK_UNSPECIFIED (0xf) until the first link has been added.
Since IEEE80211_MLD_MAX_NUM_LINKS is 15, that reads one element past the
end of the array, aliasing mt76_vif_data.offchannel_link.
Reachable via mt7996_set_tsf()/mt7996_offset_tsf() and
mt7996_net_fill_forward_path(). Bounds check link_id and return NULL,
matching mt7996_sta_link() and mt7996_sta_link_protected(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: release hif2 reference on probe IRQ failure
The hif2 reference obtained by mt7915_pci_init_hif2() is only released on
error paths that key off dev->hif2, which is not assigned until after the
IRQ setup. If pci_alloc_irq_vectors() or the primary devm_request_irq()
fails, the reference leaks. Drop it explicitly on those paths via
mt7915_put_hif2(). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: qgroup: fix a wrong length calculation in qgroup_free_reserved_data()
In that function, we round down the start position and round up the
ending position.
But during the calculation of @len, we use "round_up(start + len,
sectorsize)", which is the rounded up end position, not the rounded up
length.
Which results a much larger length, and later we are still using
"start + len", which is completely incorrect.
Fix it by declaring a local @aligned_start and @aligned_len and use them
instead. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: defrag: fix deadlock between defrag and delalloc space reservation
While running fsstress with autodefrag and flushoncommit, hit a deadlock
due to the fact that defrag reserves delalloc space while it's holding
dirty and locked folios, besides the extent range lock. The stack traces
are the following:
[958.624] task:kworker/u50:3 state:D stack:0 pid:20365 tgid:20365 ppid:2 task_flags:0x4208060 flags:0x00080000
[958.626] Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs]
[958.627] Call Trace:
[958.628] <TASK>
[958.628] __schedule+0x4be/0x10f0
[958.629] ? preempt_count_add+0x69/0xa0
[958.630] schedule+0x26/0xd0
[958.631] wait_current_trans+0x102/0x160 [btrfs]
[958.632] ? __pfx_autoremove_wake_function+0x10/0x10
[958.633] start_transaction+0x374/0x900 [btrfs]
[958.634] btrfs_commit_current_transaction+0x1d/0x70 [btrfs]
[958.635] flush_space+0xca/0x5e0 [btrfs]
[958.636] ? _raw_spin_unlock+0x15/0x30
[958.637] ? btrfs_reduce_alloc_profile+0x8c/0x190 [btrfs]
[958.639] ? _raw_spin_unlock+0x15/0x30
[958.640] ? calc_available_free_space.isra.0+0x6f/0x110 [btrfs]
[958.641] do_async_reclaim_metadata_space+0x84/0x190 [btrfs]
[958.642] btrfs_async_reclaim_metadata_space+0x64/0x80 [btrfs]
[958.644] process_one_work+0x19d/0x3a0
[958.644] worker_thread+0x1c4/0x330
[958.645] ? __pfx_worker_thread+0x10/0x10
[958.646] kthread+0xfc/0x130
[958.647] ? __pfx_kthread+0x10/0x10
[958.648] ret_from_fork+0x1f7/0x2c0
[958.648] ? __pfx_kthread+0x10/0x10
[958.649] ret_from_fork_asm+0x1a/0x30
[958.650] </TASK>
[958.651] task:kworker/u49:7 state:D stack:0 pid:52990 tgid:52990 ppid:2 task_flags:0x4208060 flags:0x00080000
[958.653] Workqueue: writeback wb_workfn (flush-btrfs-334)
[958.655] Call Trace:
[958.655] <TASK>
[958.656] __schedule+0x4be/0x10f0
[958.657] ? __blk_flush_plug+0xe9/0x140
[958.658] schedule+0x26/0xd0
[958.658] io_schedule+0x42/0x70
[958.659] folio_wait_bit_common+0x12b/0x330
[958.660] ? folio_wait_bit_common+0x100/0x330
[958.662] ? __pfx_wake_page_function+0x10/0x10
[958.663] extent_write_cache_pages+0x599/0x830 [btrfs]
[958.664] ? acpi_fwnode_get_reference_args+0x1fa/0x270
[958.665] btrfs_writepages+0x77/0x130 [btrfs]
[958.666] ? __pfx_end_bbio_data_write+0x10/0x10 [btrfs]
[958.667] do_writepages+0xc6/0x160
[958.668] __writeback_single_inode+0x42/0x310
[958.669] writeback_sb_inodes+0x231/0x570
[958.670] wb_writeback+0x8a/0x340
[958.671] wb_workfn+0xbf/0x450
[958.672] ? finish_task_switch.isra.0+0xc1/0x350
[958.673] process_one_work+0x19d/0x3a0
[958.673] worker_thread+0x1c4/0x330
[958.674] ? __pfx_worker_thread+0x10/0x10
[958.675] kthread+0xfc/0x130
[958.676] ? __pfx_kthread+0x10/0x10
[958.676] ret_from_fork+0x1f7/0x2c0
[958.677] ? __pfx_kthread+0x10/0x10
[958.678] ret_from_fork_asm+0x1a/0x30
[958.679] </TASK>
[958.679] task:btrfs-cleaner state:D stack:0 pid:296750 tgid:296750 ppid:2 task_flags:0x208040 flags:0x00080000
[958.681] Call Trace:
[958.682] <TASK>
[958.682] __schedule+0x4be/0x10f0
[958.683] schedule+0x26/0xd0
[958.684] handle_reserve_ticket+0x1b9/0x2c0 [btrfs]
[958.685] ? __pfx_autoremove_wake_function+0x10/0x10
[958.686] reserve_bytes+0x283/0x4c0 [btrfs]
[958.687] btrfs_reserve_metadata_bytes+0x18/0xb0 [btrfs]
[958.688] btrfs_delalloc_reserve_metadata+0x121/0x320 [btrfs]
[958.690] btrfs_delalloc_reserve_space+0x46/0xb0 [btrfs]
[958.691] btrfs_defrag_file+0x903/0x1110 [btrfs]
[958.692] btrfs_run_defrag_inodes+0x334/0x430 [btrfs]
[958.694] cleaner_kthread+0x97/0x1c0 [btrfs]
[958.694] ? __pfx_cleaner_kthread+0x10/0x10 [btrfs]
[958.696] kthread+0xfc/0x130
[958.696] ? __pfx_kthread+0x10/0x10
[958.697] ret_
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject load-acquire from pointers requiring fault protection
A BPF_LOAD_ACQ is not rewritten to a BPF_PROBE_MEM load by the verifier,
unlike a regular BPF_LDX, so the JIT emits a plain load with no exception
table entry and a fault panics the kernel instead of being handled.
Reject the source pointer types that a BPF_LDX would have had that fault
protection applied to, i.e. the ones bpf_convert_ctx_accesses() turns
into BPF_PROBE_MEM: a bare PTR_TO_BTF_ID, PTR_TO_BTF_ID | PTR_UNTRUSTED,
PTR_TO_BTF_ID | MEM_ALLOC | PTR_UNTRUSTED and PTR_TO_MEM | MEM_RDONLY |
PTR_UNTRUSTED.
This is reachable e.g. by loading ->mm out of a trusted task_struct
yields an untrusted pointer to mm_struct, and it is NULL for a kernel
thread:
[...]
SEC("tp_btf/sched_switch")
int BPF_PROG(demo, bool preempt, struct task_struct *prev,
struct task_struct *next)
{
struct mm_struct *mm = next->mm; /* untrusted */
out_ldx = (__u64)mm->pgd; /* BPF_LDX */
out_acq = load_acquire(&mm->pgd); /* BPF_LOAD_ACQ */
return 0;
}
[...]
Both dereference the same pointer, but only the BPF_LDX is protected
(x86-64 JIT, jump targets shown prog-relative):
[...]
; out_ldx = (__u64)mm->pgd;
17: movq $-10485760, %r10
1e: movq %rsi, %r11
21: addq $184, %r11
28: subq %r10, %r11
2b: movabsq $140737498841088, %r10
35: cmpq %r10, %r11
38: ja 0x3e <-- kernel addr?
3a: xorl %edi, %edi <-- no: dst = 0, skip the load
3c: jmp 0x45
3e: movq 184(%rsi), %rdi <-- yes: load + extable entry
[...]
; load_acquire(&mm->pgd)
53: movq %rsi, %rdi
56: movq 184(%rdi), %rax <-- no check, no extable entry
[...]
Note that BPF_PROBE_MEM is not visible in a bpftool xlated dump, as
bpf_insn_prepare_dump() rewrites it back to BPF_MEM.
A PTR_TRUSTED pointer is deliberately not on the list. Such a load is
not converted either, but it does not need to be, since the pointer is
guaranteed live, so load-acquire from it stays allowed.
The check is gated on BPF_LOAD_ACQ so that atomic RMW and store-release
error messages are unchanged; writes (RMW / store-release) to such
pointers are already rejected elsewhere, so only load-acquire needs this. |
| In the Linux kernel, the following vulnerability has been resolved:
arm_mpam: Fix a NULL pointer dereference on unbinding after an error interrupt
If a user unbinds an MSC after mpam_disable() has been run in response
to an error interrupt then a dereference of a NULL pointer occurs as
mpam_disable() sets the drvdata to NULL. Add an early return to the driver
remove callback to avoid this. |
| In the Linux kernel, the following vulnerability has been resolved:
md/md-llbitmap: prevent create failure bitmap UAF
llbitmap_create() publishes mddev->bitmap before reading the bitmap
superblock. This is needed because llbitmap_read_sb() can initialize a
new bitmap and flush it through helpers that use mddev->bitmap.
If llbitmap_read_sb() fails, the old cleanup dropped bitmap_info.mutex
and freed llbitmap before clearing mddev->bitmap. Readers such as
/proc/mdstat rely on bitmap_info.mutex to keep the bitmap pointer stable
while collecting bitmap stats, so they could observe the stale pointer
after the failed create path released the mutex.
Clear mddev->bitmap while still holding bitmap_info.mutex, then free the
failed llbitmap after dropping the mutex. This makes mutex-protected
readers see either a live bitmap or no bitmap. |
| In the Linux kernel, the following vulnerability has been resolved:
md: wait for behind writes before destroying bitmap
__md_stop() destroyed the bitmap before calling mddev_detach(). That made
mddev_detach() skip bitmap_ops->wait_behind_writes(), because the bitmap
was already disconnected from mddev.
This was still safe for the legacy bitmap because bitmap_destroy() waits
for behind writes itself. llbitmap keeps that wait in its
->wait_behind_writes() operation instead, while ->destroy() tears down the
llbitmap storage. With the old ordering, RAID1 behind-write completions
could still run after llbitmap storage had been freed.
Call mddev_detach() before md_bitmap_destroy() so the common detach path
can wait for behind writes while the bitmap is still alive. Only destroy
the bitmap after those users are gone. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: qmp-usb: Fix possible NULL-deref on early runtime suspend
There is a small window where the runtime suspend callback may run
after pm_runtime_enable() and before pm_runtime_forbid(). In this
case, a crash occurs because runtime suspend/resume dereferences
qmp->phy pointer, which is not yet initialized:
`if (!qmp->phy->init_count) {`
This can also happen if user re-enables runtime-pm via the sysfs
attribute before qmp phy is initialized.
Similarly to other qcom phy drivers, introduce a qmp->phy_initialized
variable that can be used to avoid relying on the possibly uninitialized
phy pointer. |
