| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix RX data queuing of RRO 3.0
For RRO 3.0, RX data released from a RRO data queue should be put to
the indicator queue. The frames are processed and completed in the
context of the indicator queue NAPI, which only polls skbs queued on
the MT_RXQ_RRO_IND list; frames queued under the data queue id are
left sitting on that list until the data queue NAPI happens to run,
stalling and reordering RX data. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: fix MLD ID in MAC TXD and HIF TXP
Problem:
MCU command timeout while the firmware state is normal, and the
firmware keeps showing the error log "ERROR!! NO PAUSE...".
Root cause:
If the MLD_ID field in the TXD is neither the primary link id nor the
secondary link id, it may lead to a firmware busy loop when the third
link is in power saving mode.
Remap frames directed to a third link to the primary link wcid. Since
TX status events and txfree completions carry the wcid the firmware
saw, use the remapped wcid for packet id tracking and non-AQL packet
accounting as well, while the frame keeps its original link context
for addressing, band and OMAC selection. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix non-AQL packet accounting for MLO stations
__mt76_tx_queue_skb() overrides the wcid passed by the driver with
sta->drv_priv, so the wcid might incorrectly be changed after TX,
causing wcid->non_aql_packets to be counted on the wrong wcid. For
example, on the AP side, if a station's setup link is the 5G link and
the station uses 2G to transmit a frame, the value of non_aql_packets
is increased on the 5G wcid but decreased on the 2G wcid. Once the
inflated counter exceeds MT_MAX_NON_AQL_PKT, the TX scheduler
permanently refuses to service the station.
Drop the reassignment and account on the wcid used for transmission.
This also records the actual wcid in the queue entry. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: validate RX band_idx before dereferencing phys[]
band_idx comes from a 2-bit descriptor field (0-3) and was used directly
to index dev->mt76.phys[] (size __MT_MAX_BAND == 3) and dereference the
result. A corrupt or reserved descriptor value could index out of bounds
or hit a NULL phy on parts with fewer bands. Reject invalid band indices,
mirroring mt7996_rx_get_wcid(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: clear wcid mask under mutex after RCU pointer clear
mt7915_remove_interface() cleared the wcid mask bit with no lock held and
before clearing the RCU wcid pointer. The mask is a non-atomic RMW shared
with the allocators, which all run under dev->mt76.mutex; on DBDC the two
wiphys share one mt76_dev, so this raced add_interface/sta_add on the
other band and could leak or double-hand-out a wcid. Clearing the bit
before the RCU pointer also let a concurrent allocation reuse the index
and publish its wcid, which the subsequent NULL assignment then wiped.
Move the clear into the existing mutex section, after the RCU pointer is
cleared. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: avoid nss underflow in mt7915_mcu_get_sta_nss
If a peer's VHT/HE MCS map has no supported spatial stream (all fields
0x3), the loop exits with nss == 0 and the function returned (u8)-1 (255),
which was then written into the firmware sta_rec_bf beamforming fields.
Clamp the result to 0. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix RXDMAD_C buffer recycling race
The RXDMAD_C buffers come from the RRO data queues' page pools, which are
bound to a different NAPI, so the direct page-pool recycle used here could
race the owning NAPI; take the non-direct path as is already done for WED
RX queues. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: bound TLV walk in mt7996_mcu_get_chip_config
The response TLV loop advanced by tlv->len without a minimum, so a
theoretical firmware response containing a zero-length TLV could spin
forever, hanging the CPU during device probe.
The u32 payload was also read without bounds checking.
Reject a short fixed field, stop on a TLV whose length underruns the
header or overruns the skb. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix out-of-bounds access in mmio copy helpers
mt76_mmio_write_copy() and mt76_mmio_read_copy() iterate up to
ALIGN(len, 4), so a length that is not a multiple of four reads past the
source buffer (write_copy) or writes past the destination (read_copy).
Copy the aligned body in the loop and handle the remaining tail through a
4-byte bounce buffer, keeping the register access width unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: unwind state on add_interface failure
When mt76_wcid_alloc() fails, mt7915_add_interface() returned without
clearing the vif_mask/omac_mask bits it had already set, without removing
the firmware dev info added earlier, and without clearing a monitor_vif
pointer to the vif mac80211 is about to free. mac80211 does not call
remove_interface() for a failed add, so the indices and firmware dev
entry leaked permanently and testmode could dereference the stale
monitor_vif. Add a proper error unwind. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: hold dev->mt76.mutex while disabling tx worker in SER
mt7996_mac_reset_work() parked the tx worker and disabled the RX/TX NAPIs
before taking dev->mt76.mutex. mt76_worker_disable()/_enable() are plain
kthread park/unpark, not refcounted, and __mt76_set_channel() toggles the
same worker and the MT76_RESET bit under the mutex. An L1 SER racing a
channel switch could therefore have the worker unparked and MT76_RESET
cleared while the reset path resets the DMA rings, corrupting descriptors
or tokens. Take the mutex before disabling the worker, as mt7915 does. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: reserve space for the CSA-abort countdown TLV
When a CSA countdown is active, mt7996_mcu_beacon_cntdwn() emits two
bss_bcn_cntdwn_tlv entries (the CSA countdown and the CCA-abort BCC), but
MT7996_BEACON_UPDATE_SIZE only reserved one. With MBSSID enabled and a
near-maximum beacon template the extra 8 bytes could push the offload
command past MT7996_MAX_BSS_OFFLOAD_SIZE and trigger skb_over_panic().
Reserve room for both countdown TLVs. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: cancel reset and rc work on device unregister
Both drivers cancelled dump_work on unregister but left reset_work and
rc_work to be flushed only by destroy_workqueue() in mt76_free_device(),
which runs after the hw is unregistered and the hardware stopped. A
reset_work that fires in that window calls ieee80211_restart_hw() and
re-arms mac_work on an unregistered hw, and rc_work touches station state
being torn down. Cancel both up front, alongside dump_work. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: processor: Unregister cpufreq notifier on init failure
acpi_processor_driver_init() registers the cpufreq policy notifier before
registering the ACPI processor driver and setting up CPU hotplug state.
If driver_register() or cpuhp_setup_state() fails, the error path only
unregisters the ACPI processor driver and the idle driver. The cpufreq
notifier remains registered even though initialization failed.
Mirror the module exit path on the init failure path and unregister the
cpufreq notifier when it has been registered. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: don't tear down KMS twice when KMS init fails
When priv->kms_init() (mdp4_kms_init() / mdp5_kms_init()) fails partway
through, both display drivers already tear their KMS state down via
mdp4_destroy() / mdp5_kms_destroy() before returning the error. The
common error path in msm_drm_init() then runs msm_drm_uninit() ->
msm_drm_kms_uninit(), which tries to destroy the very same KMS a second
time, which causes a use-after-free crash.
Bring MDP4/MDP5 in line with the DPU driver whose dpu_kms_init() doesn't
perform error cleanup on the failure. Let the common path own the
cleanup, instead of freeing the KMS from their error paths.
The crash trace for the reference:
__lock_acquire from lock_acquire (kernel/locking/lockdep.c:5906 kernel/locking/lockdep.c:5863)
lock_acquire from touch_wq_lockdep_map (kernel/workqueue.c:4094 (discriminator 1))
touch_wq_lockdep_map from __flush_workqueue (kernel/workqueue.c:4136)
__flush_workqueue from msm_drm_kms_uninit (drivers/gpu/drm/msm/msm_kms.c:243 (discriminator 33))
msm_drm_kms_uninit from msm_drm_uninit (drivers/gpu/drm/msm/msm_drv.c:93)
msm_drm_uninit from msm_drm_init (drivers/gpu/drm/msm/msm_drv.c:184)
msm_drm_init from try_to_bring_up_aggregate_device (drivers/base/component.c:249 drivers/base/component.c:227)
try_to_bring_up_aggregate_device from __component_add (drivers/base/component.c:269 drivers/base/component.c:748)
__component_add from dsi_host_attach (drivers/gpu/drm/msm/dsi/dsi_host.c:1739)
dsi_host_attach from mipi_dsi_attach (drivers/gpu/drm/drm_mipi_dsi.c:383)
mipi_dsi_attach from sharp_nt_panel_probe (drivers/gpu/drm/panel/panel-sharp-ls043t1le01.c:247)
Patchwork: https://patchwork.freedesktop.org/patch/742068/ |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dsi: Drop dev_pm_opp_set_rate(0)
dev_pm_opp_set_rate(0) removes the vote specified in required-opps but
does not actually park the clock, making it run without the necessary
power backing. Drop the explicit call to it.
Every call site of ops->link_clk_disable() is followed by
pm_runtime_put(), so the power vote will be rescinded if deemed safe.
Patchwork: https://patchwork.freedesktop.org/patch/742783/ |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix leak in ath11k_service_ready_ext_event()
Currently, during ath11k_service_ready_ext_event() processing,
svc_rdy_ext.mac_phy_caps can be allocated during TLV parsing. This is a
temporary allocation that is freed on the success path, but not on the
error path. If parsing succeeds far enough to allocate mac_phy_caps and
then fails on a later TLV, the allocation leaks. So free the allocation
on the error path.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: use system_freezable_wq for init complete work
schedule_delayed_work() uses system_wq, which is non-freezable, allowing
regulator_init_complete_work to run concurrently with system suspend. This
work fires ~30s after boot to disable unused regulators via I2C. When it
races with PM suspend, the I2C adapter may already be suspended, triggering
a -ESHUTDOWN warning in __i2c_transfer():
WARNING: ... at __i2c_transfer+0x36c/0x3c8
Call trace:
__i2c_transfer
i2c_transfer
regmap_i2c_write
_regmap_update_bits
regulator_disable_regmap
_regulator_do_disable
regulator_late_cleanup
regulator_init_complete_work_function
process_one_work
Switch to system_freezable_wq so the work is frozen before any device
is suspended, eliminating the race. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject >8 byte return values on return-reading trampoline paths
btf_distill_func_proto() builds the function model used for the
fentry/fexit/fmod_ret/fsession trampolines and struct_ops. It has
accepted a 16-byte __int128 return value since the trampoline was
introduced: __get_type_size() returns the integer's type size, and the
return-type check only rejected ret < 0.
But the BPF trampoline preserves only 8 bytes of the return value (RAX on
x86, i.e. R0). For an attach type that reads the target's return value the
second half (RDX / R3) is neither saved nor restored, so a program
attached to a function returning a 16-byte value corrupts the value seen
by the real caller and itself observes only half of it. struct_ops
trampolines have the same limitation.
This affects the attach types that read the target's return value: fexit,
fmod_ret and fsession (plus the _multi variants of fexit and fsession),
and struct_ops. fentry/fentry_multi run before the target returns and are
unaffected.
Reject a >8 byte return value for these attach types in
bpf_check_attach_target() and bpf_check_attach_btf_id_multi(), and for
struct_ops in bpf_struct_ops_desc_init(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, x86: Fix trampoline stack size for 128-bit arguments
btf_distill_func_proto() accepts a function argument up to 16 bytes, so a
128-bit scalar such as __int128 reaches the x86 trampoline with
arg_size == 16. But the current implementation assumes an __int128
argument only needs one register, so the register save area is
under-allocated and save_args() overwrites adjacent stack slots.
Compute the register count from arg_size for all arguments to fix it. |
