| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: master: Fix use-after-free of master->this
sysfs attribute callbacks for the master controller device dereference
master->this. However, master->this is freed in
i3c_master_detach_free_devs() before the master device itself is
released.
As a result, sysfs accesses can dereference a freed master->this
pointer, leading to a use-after-free.
Keep master->this alive until i3c_masterdev_release(), which is called
after the master device and its sysfs state are being torn down. Do not
free master->this as part of the normal device detach path.
On the error path in i3c_master_set_info(), reset master->this and
bus.cur_master to NULL before freeing the allocated device. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: master: Do not treat master device as a duplicate target
i3c_master_search_i3c_dev_duplicate() searches the bus for another I3C
device with the same PID as the reference device. The search can match
master->this, causing the controller itself to be returned as a
duplicate.
Since the controller is not a target device, it cannot be a duplicate of
one. Exclude master->this from matching so that the function only
returns real duplicate target devices. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-pcache: validate the persisted dirty_tail chain at load
The writeback worker follows the persisted dirty_tail chain, which is
decoded from the cache device independently of the key_tail chain that
cache_replay() walks and bounds. A crafted image, whose on-media fields are
authenticated only by a crc32c with a fixed seed, can aim dirty_tail at a
chain of last ksets that never terminates, so cache_writeback_fn() re-arms
itself with no delay forever.
Walk the dirty_tail chain once at load with the same hop cap cache_replay()
uses and fail the table load with -EIO if it does not reach an end within
n_segs hops. |
| In the Linux kernel, the following vulnerability has been resolved:
memcg: move LRU size accounting on reparenting instead of copying it
When a memory cgroup is offlined its LRU folios are reparented to the
parent. lruvec_reparent_lru() splices the child's lists into the
parent's and credits the parent with the child's per-zone
lru_zone_size[], but never clears the child's copy, so the size is
copied rather than moved. lru_gen_reparent_memcg() does the same for
MGLRU.
The parent is left correct, credited with exactly the folios it took
over. The stale value sits on the child and nothing will correct it:
folio->memcg_data now resolves to the parent, so every later
update_lru_size() for those folios goes there.
Dying cgroups are not freed immediately and mem_cgroup_iter() still
walks them, so shrink_lruvec() keeps being called on them.
get_scan_count() reads the phantom counter through lruvec_lru_size() and
the scan loop then grinds through nr[] in SWAP_CLUSTER_MAX steps against
an empty list, for as long as the dead cgroup lives. Under MGLRU the
MGLRU scanner runs instead, but count_shadow_nodes() sums all of
NR_LRU_LISTS through lruvec_lru_size() and over-budgets the shadow node
limit just the same.
On one 251 GiB host a sweep of every mz->lru_zone_size[] found 380
counters describing folios on no list at all: 124777314 pages, 476 GiB,
1.89x the machine's RAM, across 57 cgroups. All were on memcgs with
CSS_DYING set and CSS_ONLINE clear, and parent/child pairs reported
byte-identical sizes.
LRU_UNEVICTABLE needs its size moved too. Its list is deliberately not
spliced because lruvec_init() poisons the head - the unevictable LRU is
imaginary and folios are never threaded on it - but the size is kept by
lruvec_add_folio()/lruvec_del_folio() and those folios account to the
parent from here on.
This depends on commit bf4ade7dbd76 ("memcg: keep folio's objcg same as
its node") and must not be backported ahead of it. Without that
invariant a folio's objcg can belong to another node, so a folio already
spliced onto the parent's list can still resolve to the child's lruvec
until the objcg's node is reparented in a later iteration of
memcg_reparent_objcgs(); clearing the child's counter early then lets
lruvec_del_folio() underflow it and trip the WARN_ONCE()/VM_BUG_ON() in
mem_cgroup_update_lru_size(). |
| In the Linux kernel, the following vulnerability has been resolved:
nvdimm: virtio_pmem: refcount requests for token lifetime
KASAN reports slab-use-after-free in __wake_up_common():
BUG: KASAN: slab-use-after-free in __wake_up_common+0x114/0x160
Read of size 8 at addr ffff88810fdcb710 by task swapper/0/0
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted
6.19.0-next-20260220-00006-g1eae5f204ec3 #4 PREEMPT(full)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux
1.17.0-2-2 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x6d/0xb0
print_report+0x170/0x4e2
? __pfx__raw_spin_lock_irqsave+0x10/0x10
? __virt_addr_valid+0x1dc/0x380
kasan_report+0xbc/0xf0
? __wake_up_common+0x114/0x160
? __wake_up_common+0x114/0x160
__wake_up_common+0x114/0x160
? __pfx__raw_spin_lock_irqsave+0x10/0x10
__wake_up+0x36/0x60
virtio_pmem_host_ack+0x11d/0x3b0
? sched_balance_domains+0x29f/0xb00
? __pfx_virtio_pmem_host_ack+0x10/0x10
? _raw_spin_lock_irqsave+0x98/0x100
? __pfx__raw_spin_lock_irqsave+0x10/0x10
vring_interrupt+0x1c9/0x5e0
? __pfx_vp_interrupt+0x10/0x10
vp_vring_interrupt+0x87/0x100
? __pfx_vp_interrupt+0x10/0x10
__handle_irq_event_percpu+0x17f/0x550
? __pfx__raw_spin_lock+0x10/0x10
handle_irq_event+0xab/0x1c0
handle_fasteoi_irq+0x276/0xae0
__common_interrupt+0x65/0x130
common_interrupt+0x78/0xa0
</IRQ>
virtio_pmem_host_ack() wakes a request that has already been freed by the
submitter.
This happens when the request token is still reachable via the virtqueue,
but virtio_pmem_flush() returns and frees it.
Fix the token lifetime by refcounting struct virtio_pmem_request.
virtio_pmem_flush() holds a submitter reference, and the virtqueue holds an
extra reference once the request is queued. The completion path drops the
virtqueue reference, and the submitter drops its reference before
returning. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/bridge: synopsys: dw-dp: Support unregistering the AUX channel
The DisplayPort AUX channel gets initialized and registered during
dw_dp_bind(), but it is never unregistered, which may lead to resource
leaks and/or use-after-free.
Add the missing dw_dp_unbind() function to allow the users of the
library to handle the required cleanup, i.e. unregister the AUX adapter. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/rockchip: dw_dp: Release core resources
Core resources such as the DisplayPort AUX channel get initialized and
registered during dw_dp_bind(), but are never unregistered, which may
lead to memory leaks and/or use-after-free:
[ 224.661371] BUG: KASAN: slab-use-after-free in device_is_dependent+0xe0/0x2b0
[ 224.662015] Read of size 8 at addr ffff00011aee8550 by task modprobe/658
[ 224.662612]
[ 224.662752] CPU: 7 UID: 0 PID: 658 Comm: modprobe Not tainted 7.0.0-rc2-next-20260305 #14 PREEMPT
[ 224.662759] Hardware name: Radxa ROCK 5B (DT)
[ 224.662762] Call trace:
[ 224.662764] show_stack+0x20/0x38 (C)
[ 224.662772] dump_stack_lvl+0x6c/0x98
[ 224.662777] print_report+0x160/0x4b8
[ 224.662783] kasan_report+0xb4/0xe0
[ 224.662790] __asan_report_load8_noabort+0x20/0x30
[ 224.662796] device_is_dependent+0xe0/0x2b0
[ 224.662802] device_is_dependent+0x108/0x2b0
[ 224.662808] device_link_add+0x1f8/0x10b0
[ 224.662813] devm_of_phy_get_by_index+0x120/0x200
[ 224.662819] dw_dp_bind+0x34c/0xb10 [dw_dp]
[ 224.662830] dw_dp_rockchip_bind+0x194/0x250 [rockchipdrm]
[ 224.662864] component_bind_all+0x3a8/0x720
[ 224.662869] rockchip_drm_bind+0x120/0x390 [rockchipdrm]
[ 224.662899] try_to_bring_up_aggregate_device+0x76c/0x838
[ 224.662904] component_master_add_with_match+0x1f4/0x230
[ 224.662909] rockchip_drm_platform_probe+0x420/0x538 [rockchipdrm]
[ 224.662939] platform_probe+0xe8/0x168
[ 224.662945] really_probe+0x340/0x828
[ 224.662950] __driver_probe_device+0x2e0/0x350
[ 224.662954] driver_probe_device+0x80/0x140
[ 224.662959] __driver_attach+0x398/0x460
[ 224.662964] bus_for_each_dev+0xe0/0x198
[ 224.662968] driver_attach+0x50/0x68
[ 224.662972] bus_add_driver+0x2a0/0x4c0
[ 224.662977] driver_register+0x294/0x360
[ 224.662982] __platform_driver_register+0x7c/0x98
[ 224.662987] rockchip_drm_init+0xc4/0xff8 [rockchipdrm]
Since a previous commit exported dw_dp_unbind() function in DW DP core
library to take care of the necessary cleanup, use this in the
component's unbind() callback, as well as in its bind() error path. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/rockchip: analogix_dp: Fix OF node reference leak via auto cleanup
Sashiko reported a reference leak in rockchip_dp_drm_encoder_enable(),
the of_get_child_by_name() function does not call of_node_put() in a
symmetrical way [1].
Fix the device node reference leak by using __free(device_node) to
automatically manage of_node_put() for all device nodes. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/v3d: Clear queue->active_job when v3d_fence_create() fails
The run_job() callbacks for BIN, RENDER, TFU and CSD assign the incoming
job to queue->active_job before calling v3d_fence_create(). If
v3d_fence_create() fails, the callback returns NULL without clearing
active_job, leaving a dangling pointer.
Create a failure path in all run_job() callbacks that clears the active
job before returning NULL. The BIN path takes queue->queue_lock around the
clear as it races against v3d_overflow_mem_work(); RENDER, TFU and CSD
paths have no concurrent reader, so the clear is lock-free. |
| In the Linux kernel, the following vulnerability has been resolved:
smack: fix incorrect task context in smack_msg_queue_msgrcv
The smack_msg_queue_msgrcv() function incorrectly checks
the permissions of the 'current' task instead of the
'target' task.
In the msgsnd() syscall path, if a receiver is already waiting,
the pipelined_send() optimization is used to push the message
directly to the receiver task:
ipc/msg.c`pipelined_send():
` smp_store_release(&msr->r_msg, msg)
In this case, the 'sender' (current) task performs the check
on behalf of the 'receiver' task (msr->r_tsk, passed as the
'target' parameter):
ipc/msg.c`pipelined_send():
` security_msg_queue_msgrcv(,, target := msr->r_tsk,,)
However, smack_msg_queue_msgrcv() ignores the 'target' and
checks 'current':
smack_msg_queue_msgrcv(…)
` smk_curacc_msq(isp, MAY_READWRITE); // current task
'current' MAY satisfy smack_msg_queue_msgrcv r/w requirement,
but 'target' (the receiver task) might NOT;
as a result, an unauthorized receiver gets the message,
violating MAC policy.
Test:
1) create a sysv message queue with label “foo”
2) echo "bar foo r" >/smack/load2
3) msgrcv(,,,0,MSG_NOERROR) in "bar"-labeled task.
The task is waiting for the messages ...
4) msgsnd() from a "foo"-labeled task:
"bar"-labeled task gets the message.
This patch fixes the issue by checking permission on the
'target' task instead of 'current'.
(2008-02-04, Casey Schaufler) |
| In the Linux kernel, the following vulnerability has been resolved:
platform/chrome: cros_ec_typec: Reject out-of-bounds PD cap count
cros_typec_register_partner_pdos() copies the partner PDOs from the EC
TYPEC_STATUS response into the fixed caps_desc.pdo[PDO_MAX_OBJECTS] array.
memcpy(caps_desc.pdo, resp->source_cap_pdos,
sizeof(u32) * resp->source_cap_count);
...
memcpy(caps_desc.pdo, resp->sink_cap_pdos,
sizeof(u32) * resp->sink_cap_count);
PDO_MAX_OBJECTS is 7. source_cap_count and sink_cap_count are u8 fields
from the EC. The only check is that they are not both zero. If either is
larger than 7, the memcpy writes past the end of the array on the stack.
A count of 255 overflows it by about 1 KB. The EC source arrays are only
seven entries wide. A larger count reads past them too.
The ChromeOS EC firmware caps these counts today, so a compliant setup
does not hit this. The kernel should still validate these values rather
than trust them.
Validate the counts in cros_typec_register_partner_pdos() next to the
memcpy. Skip the PDO registration if either count is above PDO_MAX_OBJECTS.
The rest of cros_typec_handle_status() still runs so events are handled
and cleared. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: core: quiesce input in hid_hw_stop() to prevent use-after-free
A driver's probe calls hid_device_io_start() to enable input delivery,
then fails at a later initialization step and unwinds via hid_hw_stop().
The unwind frees struct hidraw via hidraw_disconnect() while in-flight
HID reports may still be running on another CPU, dereferencing the
freed object through hidraw_report_event(). syzbot reports the
resulting use-after-free for the corsair-psu HID driver.
Edward Adam Davis posted a per-driver fix for corsair-psu that adds
an explicit hid_device_io_stop() before hid_hw_stop() in the probe
error path ("hwmon: prevent packets from going to driver for probe",
2026-04-28). Auditing the tree shows 15 drivers call
hid_device_io_start(); 7 also call hid_device_io_stop() and 8 do not:
drivers calling hid_device_io_start() without a matching
hid_device_io_stop() before hid_hw_stop():
drivers/hwmon/corsair-psu.c (fix posted by Edward)
drivers/hwmon/corsair-cpro.c
drivers/hwmon/nzxt-kraken3.c
drivers/hwmon/nzxt-smart2.c
drivers/hwmon/gigabyte_waterforce.c
drivers/hid/hid-logitech-dj.c
drivers/hid/hid-nintendo.c
drivers/hid/hid-mcp2221.c
Roughly half of all callers of the API are exposed. Centralize the
quiesce in hid_hw_stop() so callers do not have to remember the
matching stop: if a driver has left hdev->io_started true on entry,
call hid_device_io_stop() before hid_disconnect().
For the 7 drivers that already call hid_device_io_stop() correctly,
hdev->io_started is false on entry, the guard short-circuits, and
behavior is unchanged.
No Fixes: tag because the affected drivers gained their
hid_device_io_start() calls independently over years; the bug is a
class-wide API misuse rather than a regression from one commit. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: roccat: bound device-supplied profile index
kone_keep_values_up_to_date() and kone_profile_activated() use an
8-bit, device-supplied profile value as an index into the 5-element
kone->profiles[] array without a range check. A malicious USB device
claiming the Roccat Kone id can send a switch-profile event (or a
startup_profile read at probe) with an out-of-range value and make the
driver read out of bounds; the result is exposed via the actual_dpi
sysfs attribute.
Reject out-of-range indices in both paths.
This was found with static analysis and confirmed with the KUnit test
added in the following patch (KASAN: slab-out-of-bounds). |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: ipc4-topology: Return error for invalid number of formats
When the number of input or output formats is zero,
sof_ipc4_widget_setup_comp_src() and sof_ipc4_widget_setup_comp_asrc()
print an error and jump to the cleanup label. At that point 'ret' is
still 0, because the earlier sof_ipc4_get_audio_fmt() call succeeded, so
the function returns success and the caller never finds out that the
widget setup actually failed.
Set ret to -EINVAL before the goto so the error gets reported. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/mbox: Clamp mailbox output allocation to the payload size
CXL_MEM_SEND_COMMAND bounds the user's in.size to the mailbox payload
size but leaves out.size unbounded, then cxl_mbox_cmd_ctor() calls
kvzalloc(out.size). A large out.size drives a huge allocation, above
INT_MAX it WARNs and taints, and with panic_on_warn=1 it panics.
The transport __cxl_pci_mbox_send_cmd() already clamps the response copy
to min(out.size, payload_size, device len), so the output buffer is
never written beyond payload_size. Clamp the allocation to payload_size
too, matching the RAW path. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: rt700-sdw: always drain jack work on remove
rt700_sdw_remove() drains jack_detect_work and jack_btn_check_work only
when rt700->hw_init is true. That state bit is cleared by
rt700_update_status() when the SoundWire slave becomes UNATTACHED, but a
jack work item can already have been queued by rt700_interrupt_callback()
or rt700_jack_init() while the device was initialized.
Do not use hw_init as the remove-time guard for draining these work
objects. The delayed works are initialized during rt700_init(), so remove
can cancel them unconditionally and pair the object lifetime with the
codec-private data lifetime instead of a mutable hardware state bit.
This issue was found by our static analysis tool and then confirmed by
manual review of the SoundWire status, interrupt and remove paths. The
remove path should drain work based on whether the work object exists, not
on a runtime hardware state bit that can change after the work was queued.
A QEMU PoC queued jack_detect_work, simulated SDW_SLAVE_UNATTACHED, and
then entered remove. DEBUG_OBJECTS reported an active timer/work object
associated with the rt700 jack work path after remove skipped the cancel.
This is sent as an RFC because the practical trigger depends on SoundWire
core remove ordering after an UNATTACHED status update. If remove cannot
run after hw_init has been cleared while jack work is still pending, this
is a defensive lifecycle cleanup rather than a reachable race on current
systems. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: fsl_audmix: rework runtime PM handling in probe
After pm_runtime_enable() the AUDMIX block is powered off and stays
suspended until the first runtime resume. Register writes issued between
probe() and the first resume (e.g. from DAPM or ALSA control paths)
target unpowered hardware and cause a system hang.
Fix this by calling pm_runtime_resume_and_get() immediately after
pm_runtime_enable() to power the hardware up and enable its clocks.
Release the reference afterwards with pm_runtime_put() to allow the
runtime PM framework to suspend the device and switch the regmap to
cache-only mode when idle.
When CONFIG_PM is disabled or runtime PM is not enabled, pm_runtime_*
calls are stubs that do not power up the hardware. Handle this case
explicitly by calling fsl_audmix_runtime_resume() directly so the
hardware is always initialised and its clocks are enabled, ensuring
register accesses succeed regardless of PM configuration. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/lima: call drm_mm_init() with a valid allocation range
lima_vm_create() is currently run before va_start and va_end are set up,
meaning they are both 0. lima_vm_create() runs drm_mm_init() with them
as arguments for the allocator, and if DRM_DEBUG_MM is enabled the
DRM_MM_BUG_ON check in drm_mm_init then fires, as seen here on
exynos4412-odroid-u2:
[ 1.736297] ------------[ cut here ]------------
[ 1.740370] kernel BUG at drivers/gpu/drm/drm_mm.c:931!
[ 1.745574] Internal error: Oops - BUG: 0 [#1] SMP ARM
[ 1.750697] Modules linked in:
[ 1.753734] CPU: 0 UID: 0 PID: 41 Comm: kworker/u16:1 Not tainted 7.0.10-postmarketos-exynos4 #11 PREEMPT
[ 1.763372] Hardware name: Samsung Exynos (Flattened Device Tree)
[ 1.769446] Workqueue: events_unbound deferred_probe_work_func
[ 1.775261] PC is at drm_mm_init+0x9c/0xa4
[ 1.779339] LR is at lima_vm_create+0x144/0x17c
[ ... ]
Fix the issue by moving the lima_vm_create() call after va_start and
va_end are set up. |
| In the Linux kernel, the following vulnerability has been resolved:
sched/fair: Fix overflow in update_tg_cfs_runnable()
A divide-by-zero crash is observed when running hackbench:
[14697.488452] CPU: 112 UID: 0 PID: 124791 Comm: hackbench Not tainted 7.1.0-rc2+
[14697.492627] RIP: 0010:propagate_entity_load_avg+0x35f/0x3e0
[14697.506799] <TASK>
[14697.507411] __dequeue_task+0x2b4/0xc70
[14697.508677] dequeue_task_fair+0x36/0x370
[14697.509047] dequeue_task+0x101/0x2f0
[14697.509426] __schedule+0x1b1/0x1a00
[14697.510868] anon_pipe_read+0x3da/0x450
[14697.511400] vfs_read+0x361/0x390
[14697.512053] __x64_sys_read+0x19/0x30
The divide-by-zero happens here:
if (scale_load_down(gcfs_rq->load.weight)) {
load_sum = div_u64(gcfs_rq->avg.load_sum,
scale_load_down(gcfs_rq->load.weight));
}
gcfs_rq->load.weight is an insane large value and is truncated
to the lower 32 bits by div_u64, which happen to be 0.
Using AI for investigation, the cause is a u32 overflow in
update_tg_cfs_runnable(), and flat pickup became a victim when using
tg_tasks():
u32 new_sum, divider;
...
new_sum = se->avg.runnable_avg * divider; <-- boom
The following sequence shows how this triggers the crash:
propagate_entity_load_avg()
update_tg_cfs_runnable() # u32 overflow corrupts runnable_sum
__update_load_avg_cfs_rq()
___update_load_avg() # computes insane runnable_avg
update_tg_load_avg() # propagates to tg->runnable_avg
update_cfs_group()
calc_concur_shares()
tg_tasks() # long-to-int truncation, negative nr
reweight_entity() # corrupted se->load.weight
update_load_add() # corrupted cfs_rq->load.weight
propagate_entity_load_avg()
update_tg_cfs_load()
div_u64() # divide-by-zero
Fix by widening new_sum from u32 to u64 (no need to force tg_tasks()
to return unsigned long after this fix) |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel/uncore: Fix uncore_box ref/unref ordering
In uncore_event_cpu_online(), uncore_box_ref() was called before
uncore_change_context(). uncore_box_ref() gates on box->cpu >= 0,
but box->cpu is still -1 at that point because uncore_change_context()
has not run yet. As a result, the box is never initialized on the
first CPU to come online in a die, leaving it permanently
uninitialized in the single-CPU-per-die case.
Thus, box->refcnt is one count below the true value, and in the CPU
offline path, the box will be torn down on the second-to-last CPU.
In uncore_event_cpu_offline(), uncore_box_unref() was called after
uncore_change_context(), so box->cpu is already -1 when the collector
CPU goes offline, which prevents it from tearing down the box.
Fix by swapping the call order in both paths so that
uncore_box_{ref,unref}() runs at the point where box->cpu reflects
the correct context.
Move allocate_boxes() out of uncore_box_ref() to enable this
reordering. |
