| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
media: rkisp1: Fix IRQ disable race issue
In rkisp1_isp_stop() and rkisp1_csi_disable() the driver masks the
interrupts and then apparently assumes that the interrupt handler won't
be running, and proceeds in the stop procedure. This is not the case, as
the interrupt handler can already be running, which would lead to the
ISP being disabled while the interrupt handler handling a captured
frame.
This brings up two issues: 1) the ISP could be powered off while the
interrupt handler is still running and accessing registers, leading to
board lockup, and 2) the interrupt handler code and the code that
disables the streaming might do things that conflict.
It is not clear to me if 2) causes a real issue, but 1) can be seen with
a suitable delay (or printk in my case) in the interrupt handler,
leading to board lockup. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/ipoib: Fix mcast list locking
Releasing the `priv->lock` while iterating the `priv->multicast_list` in
`ipoib_mcast_join_task()` opens a window for `ipoib_mcast_dev_flush()` to
remove the items while in the middle of iteration. If the mcast is removed
while the lock was dropped, the for loop spins forever resulting in a hard
lockup (as was reported on RHEL 4.18.0-372.75.1.el8_6 kernel):
Task A (kworker/u72:2 below) | Task B (kworker/u72:0 below)
-----------------------------------+-----------------------------------
ipoib_mcast_join_task(work) | ipoib_ib_dev_flush_light(work)
spin_lock_irq(&priv->lock) | __ipoib_ib_dev_flush(priv, ...)
list_for_each_entry(mcast, | ipoib_mcast_dev_flush(dev = priv->dev)
&priv->multicast_list, list) |
ipoib_mcast_join(dev, mcast) |
spin_unlock_irq(&priv->lock) |
| spin_lock_irqsave(&priv->lock, flags)
| list_for_each_entry_safe(mcast, tmcast,
| &priv->multicast_list, list)
| list_del(&mcast->list);
| list_add_tail(&mcast->list, &remove_list)
| spin_unlock_irqrestore(&priv->lock, flags)
spin_lock_irq(&priv->lock) |
| ipoib_mcast_remove_list(&remove_list)
(Here, `mcast` is no longer on the | list_for_each_entry_safe(mcast, tmcast,
`priv->multicast_list` and we keep | remove_list, list)
spinning on the `remove_list` of | >>> wait_for_completion(&mcast->done)
the other thread which is blocked |
and the list is still valid on |
it's stack.)
Fix this by keeping the lock held and changing to GFP_ATOMIC to prevent
eventual sleeps.
Unfortunately we could not reproduce the lockup and confirm this fix but
based on the code review I think this fix should address such lockups.
crash> bc 31
PID: 747 TASK: ff1c6a1a007e8000 CPU: 31 COMMAND: "kworker/u72:2"
--
[exception RIP: ipoib_mcast_join_task+0x1b1]
RIP: ffffffffc0944ac1 RSP: ff646f199a8c7e00 RFLAGS: 00000002
RAX: 0000000000000000 RBX: ff1c6a1a04dc82f8 RCX: 0000000000000000
work (&priv->mcast_task{,.work})
RDX: ff1c6a192d60ac68 RSI: 0000000000000286 RDI: ff1c6a1a04dc8000
&mcast->list
RBP: ff646f199a8c7e90 R8: ff1c699980019420 R9: ff1c6a1920c9a000
R10: ff646f199a8c7e00 R11: ff1c6a191a7d9800 R12: ff1c6a192d60ac00
mcast
R13: ff1c6a1d82200000 R14: ff1c6a1a04dc8000 R15: ff1c6a1a04dc82d8
dev priv (&priv->lock) &priv->multicast_list (aka head)
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
--- <NMI exception stack> ---
#5 [ff646f199a8c7e00] ipoib_mcast_join_task+0x1b1 at ffffffffc0944ac1 [ib_ipoib]
#6 [ff646f199a8c7e98] process_one_work+0x1a7 at ffffffff9bf10967
crash> rx ff646f199a8c7e68
ff646f199a8c7e68: ff1c6a1a04dc82f8 <<< work = &priv->mcast_task.work
crash> list -hO ipoib_dev_priv.multicast_list ff1c6a1a04dc8000
(empty)
crash> ipoib_dev_priv.mcast_task.work.func,mcast_mutex.owner.counter ff1c6a1a04dc8000
mcast_task.work.func = 0xffffffffc0944910 <ipoib_mcast_join_task>,
mcast_mutex.owner.counter = 0xff1c69998efec000
crash> b 8
PID: 8 TASK: ff1c69998efec000 CPU: 33 COMMAND: "kworker/u72:0"
--
#3 [ff646f1980153d50] wait_for_completion+0x96 at ffffffff9c7d7646
#4 [ff646f1980153d90] ipoib_mcast_remove_list+0x56 at ffffffffc0944dc6 [ib_ipoib]
#5 [ff646f1980153de8] ipoib_mcast_dev_flush+0x1a7 at ffffffffc09455a7 [ib_ipoib]
#6 [ff646f1980153e58] __ipoib_ib_dev_flush+0x1a4 at ffffffffc09431a4 [ib_ipoib]
#7 [ff
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm, kexec, ima: Use memblock_free_late() from ima_free_kexec_buffer()
The code calling ima_free_kexec_buffer() runs long after the memblock
allocator has already been torn down, potentially resulting in a use
after free in memblock_isolate_range().
With KASAN or KFENCE, this use after free will result in a BUG
from the idle task, and a subsequent kernel panic.
Switch ima_free_kexec_buffer() over to memblock_free_late() to avoid
that bug. |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix potential use after free in nilfs_gccache_submit_read_data()
In nilfs_gccache_submit_read_data(), brelse(bh) is called to drop the
reference count of bh when the call to nilfs_dat_translate() fails. If
the reference count hits 0 and its owner page gets unlocked, bh may be
freed. However, bh->b_page is dereferenced to put the page after that,
which may result in a use-after-free bug. This patch moves the release
operation after unlocking and putting the page.
NOTE: The function in question is only called in GC, and in combination
with current userland tools, address translation using DAT does not occur
in that function, so the code path that causes this issue will not be
executed. However, it is possible to run that code path by intentionally
modifying the userland GC library or by calling the GC ioctl directly.
[konishi.ryusuke@gmail.com: NOTE added to the commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock
__dma_entry_alloc_check_leak() calls into printk -> serial console
output (qcom geni) and grabs port->lock under free_entries_lock
spin lock, which is a reverse locking dependency chain as qcom_geni
IRQ handler can call into dma-debug code and grab free_entries_lock
under port->lock.
Move __dma_entry_alloc_check_leak() call out of free_entries_lock
scope so that we don't acquire serial console's port->lock under it.
Trimmed-down lockdep splat:
The existing dependency chain (in reverse order) is:
-> #2 (free_entries_lock){-.-.}-{2:2}:
_raw_spin_lock_irqsave+0x60/0x80
dma_entry_alloc+0x38/0x110
debug_dma_map_page+0x60/0xf8
dma_map_page_attrs+0x1e0/0x230
dma_map_single_attrs.constprop.0+0x6c/0xc8
geni_se_rx_dma_prep+0x40/0xcc
qcom_geni_serial_isr+0x310/0x510
__handle_irq_event_percpu+0x110/0x244
handle_irq_event_percpu+0x20/0x54
handle_irq_event+0x50/0x88
handle_fasteoi_irq+0xa4/0xcc
handle_irq_desc+0x28/0x40
generic_handle_domain_irq+0x24/0x30
gic_handle_irq+0xc4/0x148
do_interrupt_handler+0xa4/0xb0
el1_interrupt+0x34/0x64
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x64/0x68
arch_local_irq_enable+0x4/0x8
____do_softirq+0x18/0x24
...
-> #1 (&port_lock_key){-.-.}-{2:2}:
_raw_spin_lock_irqsave+0x60/0x80
qcom_geni_serial_console_write+0x184/0x1dc
console_flush_all+0x344/0x454
console_unlock+0x94/0xf0
vprintk_emit+0x238/0x24c
vprintk_default+0x3c/0x48
vprintk+0xb4/0xbc
_printk+0x68/0x90
register_console+0x230/0x38c
uart_add_one_port+0x338/0x494
qcom_geni_serial_probe+0x390/0x424
platform_probe+0x70/0xc0
really_probe+0x148/0x280
__driver_probe_device+0xfc/0x114
driver_probe_device+0x44/0x100
__device_attach_driver+0x64/0xdc
bus_for_each_drv+0xb0/0xd8
__device_attach+0xe4/0x140
device_initial_probe+0x1c/0x28
bus_probe_device+0x44/0xb0
device_add+0x538/0x668
of_device_add+0x44/0x50
of_platform_device_create_pdata+0x94/0xc8
of_platform_bus_create+0x270/0x304
of_platform_populate+0xac/0xc4
devm_of_platform_populate+0x60/0xac
geni_se_probe+0x154/0x160
platform_probe+0x70/0xc0
...
-> #0 (console_owner){-...}-{0:0}:
__lock_acquire+0xdf8/0x109c
lock_acquire+0x234/0x284
console_flush_all+0x330/0x454
console_unlock+0x94/0xf0
vprintk_emit+0x238/0x24c
vprintk_default+0x3c/0x48
vprintk+0xb4/0xbc
_printk+0x68/0x90
dma_entry_alloc+0xb4/0x110
debug_dma_map_sg+0xdc/0x2f8
__dma_map_sg_attrs+0xac/0xe4
dma_map_sgtable+0x30/0x4c
get_pages+0x1d4/0x1e4 [msm]
msm_gem_pin_pages_locked+0x38/0xac [msm]
msm_gem_pin_vma_locked+0x58/0x88 [msm]
msm_ioctl_gem_submit+0xde4/0x13ac [msm]
drm_ioctl_kernel+0xe0/0x15c
drm_ioctl+0x2e8/0x3f4
vfs_ioctl+0x30/0x50
...
Chain exists of:
console_owner --> &port_lock_key --> free_entries_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(free_entries_lock);
lock(&port_lock_key);
lock(free_entries_lock);
lock(console_owner);
*** DEADLOCK ***
Call trace:
dump_backtrace+0xb4/0xf0
show_stack+0x20/0x30
dump_stack_lvl+0x60/0x84
dump_stack+0x18/0x24
print_circular_bug+0x1cc/0x234
check_noncircular+0x78/0xac
__lock_acquire+0xdf8/0x109c
lock_acquire+0x234/0x284
console_flush_all+0x330/0x454
consol
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: ca8210: Fix a potential UAF in ca8210_probe
If of_clk_add_provider() fails in ca8210_register_ext_clock(),
it calls clk_unregister() to release priv->clk and returns an
error. However, the caller ca8210_probe() then calls ca8210_remove(),
where priv->clk is freed again in ca8210_unregister_ext_clock(). In
this case, a use-after-free may happen in the second time we call
clk_unregister().
Fix this by removing the first clk_unregister(). Also, priv->clk could
be an error code on failure of clk_register_fixed_rate(). Use
IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock(). |
| In the Linux kernel, the following vulnerability has been resolved:
ravb: Fix use-after-free issue in ravb_tx_timeout_work()
The ravb_stop() should call cancel_work_sync(). Otherwise,
ravb_tx_timeout_work() is possible to use the freed priv after
ravb_remove() was called like below:
CPU0 CPU1
ravb_tx_timeout()
ravb_remove()
unregister_netdev()
free_netdev(ndev)
// free priv
ravb_tx_timeout_work()
// use priv
unregister_netdev() will call .ndo_stop() so that ravb_stop() is
called. And, after phy_stop() is called, netif_carrier_off()
is also called. So that .ndo_tx_timeout() will not be called
after phy_stop(). |
| In the Linux kernel, the following vulnerability has been resolved:
phy: lynx-28g: serialize concurrent phy_set_mode_ext() calls to shared registers
The protocol converter configuration registers PCC8, PCCC, PCCD
(implemented by the driver), as well as others, control protocol
converters from multiple lanes (each represented as a different
struct phy). So, if there are simultaneous calls to phy_set_mode_ext()
to lanes sharing the same PCC register (either for the "old" or for the
"new" protocol), corruption of the values programmed to hardware is
possible, because lynx_28g_rmw() has no locking.
Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take
the global spinlock from the phy_ops :: set_mode() implementation. There
are no other callers which modify PCC registers. |
| In the Linux kernel, the following vulnerability has been resolved:
tee: amdtee: fix use-after-free vulnerability in amdtee_close_session
There is a potential race condition in amdtee_close_session that may
cause use-after-free in amdtee_open_session. For instance, if a session
has refcount == 1, and one thread tries to free this session via:
kref_put(&sess->refcount, destroy_session);
the reference count will get decremented, and the next step would be to
call destroy_session(). However, if in another thread,
amdtee_open_session() is called before destroy_session() has completed
execution, alloc_session() may return 'sess' that will be freed up
later in destroy_session() leading to use-after-free in
amdtee_open_session.
To fix this issue, treat decrement of sess->refcount and removal of
'sess' from session list in destroy_session() as a critical section, so
that it is executed atomically. |
| In the Linux kernel, the following vulnerability has been resolved:
net: nfc: fix races in nfc_llcp_sock_get() and nfc_llcp_sock_get_sn()
Sili Luo reported a race in nfc_llcp_sock_get(), leading to UAF.
Getting a reference on the socket found in a lookup while
holding a lock should happen before releasing the lock.
nfc_llcp_sock_get_sn() has a similar problem.
Finally nfc_llcp_recv_snl() needs to make sure the socket
found by nfc_llcp_sock_from_sn() does not disappear. |
| In the Linux kernel, the following vulnerability has been resolved:
bus: mhi: host: Drop chan lock before queuing buffers
Ensure read and write locks for the channel are not taken in succession by
dropping the read lock from parse_xfer_event() such that a callback given
to client can potentially queue buffers and acquire the write lock in that
process. Any queueing of buffers should be done without channel read lock
acquired as it can result in multiple locks and a soft lockup.
[mani: added fixes tag and cc'ed stable] |
| In the Linux kernel, the following vulnerability has been resolved:
media: mtk-jpeg: Fix use after free bug due to error path handling in mtk_jpeg_dec_device_run
In mtk_jpeg_probe, &jpeg->job_timeout_work is bound with
mtk_jpeg_job_timeout_work.
In mtk_jpeg_dec_device_run, if error happens in
mtk_jpeg_set_dec_dst, it will finally start the worker while
mark the job as finished by invoking v4l2_m2m_job_finish.
There are two methods to trigger the bug. If we remove the
module, it which will call mtk_jpeg_remove to make cleanup.
The possible sequence is as follows, which will cause a
use-after-free bug.
CPU0 CPU1
mtk_jpeg_dec_... |
start worker |
|mtk_jpeg_job_timeout_work
mtk_jpeg_remove |
v4l2_m2m_release |
kfree(m2m_dev); |
|
| v4l2_m2m_get_curr_priv
| m2m_dev->curr_ctx //use
If we close the file descriptor, which will call mtk_jpeg_release,
it will have a similar sequence.
Fix this bug by starting timeout worker only if started jpegdec worker
successfully. Then v4l2_m2m_job_finish will only be called in
either mtk_jpeg_job_timeout_work or mtk_jpeg_dec_device_run. |
| In the Linux kernel, the following vulnerability has been resolved:
mctp: perform route lookups under a RCU read-side lock
Our current route lookups (mctp_route_lookup and mctp_route_lookup_null)
traverse the net's route list without the RCU read lock held. This means
the route lookup is subject to preemption, resulting in an potential
grace period expiry, and so an eventual kfree() while we still have the
route pointer.
Add the proper read-side critical section locks around the route
lookups, preventing premption and a possible parallel kfree.
The remaining net->mctp.routes accesses are already under a
rcu_read_lock, or protected by the RTNL for updates.
Based on an analysis from Sili Luo <rootlab@huawei.com>, where
introducing a delay in the route lookup could cause a UAF on
simultaneous sendmsg() and route deletion. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix uaf in smb20_oplock_break_ack
drop reference after use opinfo. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: powermate - fix use-after-free in powermate_config_complete
syzbot has found a use-after-free bug [1] in the powermate driver. This
happens when the device is disconnected, which leads to a memory free from
the powermate_device struct. When an asynchronous control message
completes after the kfree and its callback is invoked, the lock does not
exist anymore and hence the bug.
Use usb_kill_urb() on pm->config to cancel any in-progress requests upon
device disconnection.
[1] https://syzkaller.appspot.com/bug?extid=0434ac83f907a1dbdd1e |
| In the Linux kernel, the following vulnerability has been resolved:
drivers/amd/pm: fix a use-after-free in kv_parse_power_table
When ps allocated by kzalloc equals to NULL, kv_parse_power_table
frees adev->pm.dpm.ps that allocated before. However, after the control
flow goes through the following call chains:
kv_parse_power_table
|-> kv_dpm_init
|-> kv_dpm_sw_init
|-> kv_dpm_fini
The adev->pm.dpm.ps is used in the for loop of kv_dpm_fini after its
first free in kv_parse_power_table and causes a use-after-free bug. |
| In the Linux kernel, the following vulnerability has been resolved:
class: fix use-after-free in class_register()
The lock_class_key is still registered and can be found in
lock_keys_hash hlist after subsys_private is freed in error
handler path.A task who iterate over the lock_keys_hash
later may cause use-after-free.So fix that up and unregister
the lock_class_key before kfree(cp).
On our platform, a driver fails to kset_register because of
creating duplicate filename '/class/xxx'.With Kasan enabled,
it prints a invalid-access bug report.
KASAN bug report:
BUG: KASAN: invalid-access in lockdep_register_key+0x19c/0x1bc
Write of size 8 at addr 15ffff808b8c0368 by task modprobe/252
Pointer tag: [15], memory tag: [fe]
CPU: 7 PID: 252 Comm: modprobe Tainted: G W
6.6.0-mainline-maybe-dirty #1
Call trace:
dump_backtrace+0x1b0/0x1e4
show_stack+0x2c/0x40
dump_stack_lvl+0xac/0xe0
print_report+0x18c/0x4d8
kasan_report+0xe8/0x148
__hwasan_store8_noabort+0x88/0x98
lockdep_register_key+0x19c/0x1bc
class_register+0x94/0x1ec
init_module+0xbc/0xf48 [rfkill]
do_one_initcall+0x17c/0x72c
do_init_module+0x19c/0x3f8
...
Memory state around the buggy address:
ffffff808b8c0100: 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a 8a
ffffff808b8c0200: 8a 8a 8a 8a 8a 8a 8a 8a fe fe fe fe fe fe fe fe
>ffffff808b8c0300: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
^
ffffff808b8c0400: 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03
As CONFIG_KASAN_GENERIC is not set, Kasan reports invalid-access
not use-after-free here.In this case, modprobe is manipulating
the corrupted lock_keys_hash hlish where lock_class_key is already
freed before.
It's worth noting that this only can happen if lockdep is enabled,
which is not true for normal system. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Defer the free of inner map when necessary
When updating or deleting an inner map in map array or map htab, the map
may still be accessed by non-sleepable program or sleepable program.
However bpf_map_fd_put_ptr() decreases the ref-counter of the inner map
directly through bpf_map_put(), if the ref-counter is the last one
(which is true for most cases), the inner map will be freed by
ops->map_free() in a kworker. But for now, most .map_free() callbacks
don't use synchronize_rcu() or its variants to wait for the elapse of a
RCU grace period, so after the invocation of ops->map_free completes,
the bpf program which is accessing the inner map may incur
use-after-free problem.
Fix the free of inner map by invoking bpf_map_free_deferred() after both
one RCU grace period and one tasks trace RCU grace period if the inner
map has been removed from the outer map before. The deferment is
accomplished by using call_rcu() or call_rcu_tasks_trace() when
releasing the last ref-counter of bpf map. The newly-added rcu_head
field in bpf_map shares the same storage space with work field to
reduce the size of bpf_map. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix a race condition between btf_put() and map_free()
When running `./test_progs -j` in my local vm with latest kernel,
I once hit a kasan error like below:
[ 1887.184724] BUG: KASAN: slab-use-after-free in bpf_rb_root_free+0x1f8/0x2b0
[ 1887.185599] Read of size 4 at addr ffff888106806910 by task kworker/u12:2/2830
[ 1887.186498]
[ 1887.186712] CPU: 3 PID: 2830 Comm: kworker/u12:2 Tainted: G OEL 6.7.0-rc3-00699-g90679706d486-dirty #494
[ 1887.188034] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 1887.189618] Workqueue: events_unbound bpf_map_free_deferred
[ 1887.190341] Call Trace:
[ 1887.190666] <TASK>
[ 1887.190949] dump_stack_lvl+0xac/0xe0
[ 1887.191423] ? nf_tcp_handle_invalid+0x1b0/0x1b0
[ 1887.192019] ? panic+0x3c0/0x3c0
[ 1887.192449] print_report+0x14f/0x720
[ 1887.192930] ? preempt_count_sub+0x1c/0xd0
[ 1887.193459] ? __virt_addr_valid+0xac/0x120
[ 1887.194004] ? bpf_rb_root_free+0x1f8/0x2b0
[ 1887.194572] kasan_report+0xc3/0x100
[ 1887.195085] ? bpf_rb_root_free+0x1f8/0x2b0
[ 1887.195668] bpf_rb_root_free+0x1f8/0x2b0
[ 1887.196183] ? __bpf_obj_drop_impl+0xb0/0xb0
[ 1887.196736] ? preempt_count_sub+0x1c/0xd0
[ 1887.197270] ? preempt_count_sub+0x1c/0xd0
[ 1887.197802] ? _raw_spin_unlock+0x1f/0x40
[ 1887.198319] bpf_obj_free_fields+0x1d4/0x260
[ 1887.198883] array_map_free+0x1a3/0x260
[ 1887.199380] bpf_map_free_deferred+0x7b/0xe0
[ 1887.199943] process_scheduled_works+0x3a2/0x6c0
[ 1887.200549] worker_thread+0x633/0x890
[ 1887.201047] ? __kthread_parkme+0xd7/0xf0
[ 1887.201574] ? kthread+0x102/0x1d0
[ 1887.202020] kthread+0x1ab/0x1d0
[ 1887.202447] ? pr_cont_work+0x270/0x270
[ 1887.202954] ? kthread_blkcg+0x50/0x50
[ 1887.203444] ret_from_fork+0x34/0x50
[ 1887.203914] ? kthread_blkcg+0x50/0x50
[ 1887.204397] ret_from_fork_asm+0x11/0x20
[ 1887.204913] </TASK>
[ 1887.204913] </TASK>
[ 1887.205209]
[ 1887.205416] Allocated by task 2197:
[ 1887.205881] kasan_set_track+0x3f/0x60
[ 1887.206366] __kasan_kmalloc+0x6e/0x80
[ 1887.206856] __kmalloc+0xac/0x1a0
[ 1887.207293] btf_parse_fields+0xa15/0x1480
[ 1887.207836] btf_parse_struct_metas+0x566/0x670
[ 1887.208387] btf_new_fd+0x294/0x4d0
[ 1887.208851] __sys_bpf+0x4ba/0x600
[ 1887.209292] __x64_sys_bpf+0x41/0x50
[ 1887.209762] do_syscall_64+0x4c/0xf0
[ 1887.210222] entry_SYSCALL_64_after_hwframe+0x63/0x6b
[ 1887.210868]
[ 1887.211074] Freed by task 36:
[ 1887.211460] kasan_set_track+0x3f/0x60
[ 1887.211951] kasan_save_free_info+0x28/0x40
[ 1887.212485] ____kasan_slab_free+0x101/0x180
[ 1887.213027] __kmem_cache_free+0xe4/0x210
[ 1887.213514] btf_free+0x5b/0x130
[ 1887.213918] rcu_core+0x638/0xcc0
[ 1887.214347] __do_softirq+0x114/0x37e
The error happens at bpf_rb_root_free+0x1f8/0x2b0:
00000000000034c0 <bpf_rb_root_free>:
; {
34c0: f3 0f 1e fa endbr64
34c4: e8 00 00 00 00 callq 0x34c9 <bpf_rb_root_free+0x9>
34c9: 55 pushq %rbp
34ca: 48 89 e5 movq %rsp, %rbp
...
; if (rec && rec->refcount_off >= 0 &&
36aa: 4d 85 ed testq %r13, %r13
36ad: 74 a9 je 0x3658 <bpf_rb_root_free+0x198>
36af: 49 8d 7d 10 leaq 0x10(%r13), %rdi
36b3: e8 00 00 00 00 callq 0x36b8 <bpf_rb_root_free+0x1f8>
<==== kasan function
36b8: 45 8b 7d 10 movl 0x10(%r13), %r15d
<==== use-after-free load
36bc: 45 85 ff testl %r15d, %r15d
36bf: 78 8c js 0x364d <bpf_rb_root_free+0x18d>
So the problem
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
media: pvrusb2: fix use after free on context disconnection
Upon module load, a kthread is created targeting the
pvr2_context_thread_func function, which may call pvr2_context_destroy
and thus call kfree() on the context object. However, that might happen
before the usb hub_event handler is able to notify the driver. This
patch adds a sanity check before the invalid read reported by syzbot,
within the context disconnection call stack. |
