| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
fs: Protect reconfiguration of sb read-write from racing writes
The reconfigure / remount code takes a lot of effort to protect
filesystem's reconfiguration code from racing writes on remounting
read-only. However during remounting read-only filesystem to read-write
mode userspace writes can start immediately once we clear SB_RDONLY
flag. This is inconvenient for example for ext4 because we need to do
some writes to the filesystem (such as preparation of quota files)
before we can take userspace writes so we are clearing SB_RDONLY flag
before we are fully ready to accept userpace writes and syzbot has found
a way to exploit this [1]. Also as far as I'm reading the code
the filesystem remount code was protected from racing writes in the
legacy mount path by the mount's MNT_READONLY flag so this is relatively
new problem. It is actually fairly easy to protect remount read-write
from racing writes using sb->s_readonly_remount flag so let's just do
that instead of having to workaround these races in the filesystem code.
[1] https://lore.kernel.org/all/00000000000006a0df05f6667499@google.com/T/ |
| In the Linux kernel, the following vulnerability has been resolved:
net: nsh: Use correct mac_offset to unwind gso skb in nsh_gso_segment()
As the call trace shows, skb_panic was caused by wrong skb->mac_header
in nsh_gso_segment():
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 3 PID: 2737 Comm: syz Not tainted 6.3.0-next-20230505 #1
RIP: 0010:skb_panic+0xda/0xe0
call Trace:
skb_push+0x91/0xa0
nsh_gso_segment+0x4f3/0x570
skb_mac_gso_segment+0x19e/0x270
__skb_gso_segment+0x1e8/0x3c0
validate_xmit_skb+0x452/0x890
validate_xmit_skb_list+0x99/0xd0
sch_direct_xmit+0x294/0x7c0
__dev_queue_xmit+0x16f0/0x1d70
packet_xmit+0x185/0x210
packet_snd+0xc15/0x1170
packet_sendmsg+0x7b/0xa0
sock_sendmsg+0x14f/0x160
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
nsh_gso_segment
nhoff = skb->network_header - skb->mac_header;
__skb_pull(skb,nsh_len)
skb_mac_gso_segment
mpls_gso_segment
skb_reset_network_header(skb);//skb->network_header+=nsh_len
return -EINVAL;
skb_gso_error_unwind
skb_push(skb, nsh_len);
skb->mac_header = skb->network_header - nhoff;
// skb->mac_header > skb->headroom, cause skb_push panic
Use correct mac_offset to restore mac_header and get rid of nhoff. |
| In the Linux kernel, the following vulnerability has been resolved:
pcmcia: rsrc_nonstatic: Fix memory leak in nonstatic_release_resource_db()
When nonstatic_release_resource_db() frees all resources associated
with an PCMCIA socket, it forgets to free socket_data too, causing
a memory leak observable with kmemleak:
unreferenced object 0xc28d1000 (size 64):
comm "systemd-udevd", pid 297, jiffies 4294898478 (age 194.484s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 f0 85 0e c3 00 00 00 00 ................
00 00 00 00 0c 10 8d c2 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffda4245>] __kmem_cache_alloc_node+0x2d7/0x4a0
[<7e51f0c8>] kmalloc_trace+0x31/0xa4
[<d52b4ca0>] nonstatic_init+0x24/0x1a4 [pcmcia_rsrc]
[<a2f13e08>] pcmcia_register_socket+0x200/0x35c [pcmcia_core]
[<a728be1b>] yenta_probe+0x4d8/0xa70 [yenta_socket]
[<c48fac39>] pci_device_probe+0x99/0x194
[<84b7c690>] really_probe+0x181/0x45c
[<8060fe6e>] __driver_probe_device+0x75/0x1f4
[<b9b76f43>] driver_probe_device+0x28/0xac
[<648b766f>] __driver_attach+0xeb/0x1e4
[<6e9659eb>] bus_for_each_dev+0x61/0xb4
[<25a669f3>] driver_attach+0x1e/0x28
[<d8671d6b>] bus_add_driver+0x102/0x20c
[<df0d323c>] driver_register+0x5b/0x120
[<942cd8a4>] __pci_register_driver+0x44/0x4c
[<e536027e>] __UNIQUE_ID___addressable_cleanup_module188+0x1c/0xfffff000 [iTCO_vendor_support]
Fix this by freeing socket_data too.
Tested on a Acer Travelmate 4002WLMi by manually binding/unbinding
the yenta_cardbus driver (yenta_socket). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/dcssblk: fix kernel crash with list_add corruption
Commit fb08a1908cb1 ("dax: simplify the dax_device <-> gendisk
association") introduced new logic for gendisk association, requiring
drivers to explicitly call dax_add_host() and dax_remove_host().
For dcssblk driver, some dax_remove_host() calls were missing, e.g. in
device remove path. The commit also broke error handling for out_dax case
in device add path, resulting in an extra put_device() w/o the previous
get_device() in that case.
This lead to stale xarray entries after device add / remove cycles. In the
case when a previously used struct gendisk pointer (xarray index) would be
used again, because blk_alloc_disk() happened to return such a pointer, the
xa_insert() in dax_add_host() would fail and go to out_dax, doing the extra
put_device() in the error path. In combination with an already flawed error
handling in dcssblk (device_register() cleanup), which needs to be
addressed in a separate patch, this resulted in a missing device_del() /
klist_del(), and eventually in the kernel crash with list_add corruption on
a subsequent device_add() / klist_add().
Fix this by adding the missing dax_remove_host() calls, and also move the
put_device() in the error path to restore the previous logic. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: sc16is7xx: setup GPIO controller later in probe
The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.
This issue manifests itself as an Oops when the GPIO lines are configured:
Unable to handle kernel read from unreadable memory at virtual address
...
pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
...
Call trace:
sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
gpiod_direction_output_raw_commit+0x64/0x318
gpiod_direction_output+0xb0/0x170
create_gpio_led+0xec/0x198
gpio_led_probe+0x16c/0x4f0
platform_drv_probe+0x5c/0xb0
really_probe+0xe8/0x448
driver_probe_device+0xe8/0x138
__device_attach_driver+0x94/0x118
bus_for_each_drv+0x8c/0xe0
__device_attach+0x100/0x1b8
device_initial_probe+0x28/0x38
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xe0
process_one_work+0x1c4/0x480
worker_thread+0x54/0x430
kthread+0x138/0x150
ret_from_fork+0x10/0x1c
This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix incorrect splitting in btrfs_drop_extent_map_range
In production we were seeing a variety of WARN_ON()'s in the extent_map
code, specifically in btrfs_drop_extent_map_range() when we have to call
add_extent_mapping() for our second split.
Consider the following extent map layout
PINNED
[0 16K) [32K, 48K)
and then we call btrfs_drop_extent_map_range for [0, 36K), with
skip_pinned == true. The initial loop will have
start = 0
end = 36K
len = 36K
we will find the [0, 16k) extent, but since we are pinned we will skip
it, which has this code
start = em_end;
if (end != (u64)-1)
len = start + len - em_end;
em_end here is 16K, so now the values are
start = 16K
len = 16K + 36K - 16K = 36K
len should instead be 20K. This is a problem when we find the next
extent at [32K, 48K), we need to split this extent to leave [36K, 48k),
however the code for the split looks like this
split->start = start + len;
split->len = em_end - (start + len);
In this case we have
em_end = 48K
split->start = 16K + 36K // this should be 16K + 20K
split->len = 48K - (16K + 36K) // this overflows as 16K + 36K is 52K
and now we have an invalid extent_map in the tree that potentially
overlaps other entries in the extent map. Even in the non-overlapping
case we will have split->start set improperly, which will cause problems
with any block related calculations.
We don't actually need len in this loop, we can simply use end as our
end point, and only adjust start up when we find a pinned extent we need
to skip.
Adjust the logic to do this, which keeps us from inserting an invalid
extent map.
We only skip_pinned in the relocation case, so this is relatively rare,
except in the case where you are running relocation a lot, which can
happen with auto relocation on. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to drop all dirty pages during umount() if cp_error is set
xfstest generic/361 reports a bug as below:
f2fs_bug_on(sbi, sbi->fsync_node_num);
kernel BUG at fs/f2fs/super.c:1627!
RIP: 0010:f2fs_put_super+0x3a8/0x3b0
Call Trace:
generic_shutdown_super+0x8c/0x1b0
kill_block_super+0x2b/0x60
kill_f2fs_super+0x87/0x110
deactivate_locked_super+0x39/0x80
deactivate_super+0x46/0x50
cleanup_mnt+0x109/0x170
__cleanup_mnt+0x16/0x20
task_work_run+0x65/0xa0
exit_to_user_mode_prepare+0x175/0x190
syscall_exit_to_user_mode+0x25/0x50
do_syscall_64+0x4c/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
During umount(), if cp_error is set, f2fs_wait_on_all_pages() should
not stop waiting all F2FS_WB_CP_DATA pages to be writebacked, otherwise,
fsync_node_num can be non-zero after f2fs_wait_on_all_pages() causing
this bug.
In this case, to avoid deadloop in f2fs_wait_on_all_pages(), it needs
to drop all dirty pages rather than redirtying them. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: safexcel - Cleanup ring IRQ workqueues on load failure
A failure loading the safexcel driver results in the following warning
on boot, because the IRQ affinity has not been correctly cleaned up.
Ensure we clean up the affinity and workqueues on a failure to load the
driver.
crypto-safexcel: probe of f2800000.crypto failed with error -2
------------[ cut here ]------------
WARNING: CPU: 1 PID: 232 at kernel/irq/manage.c:1913 free_irq+0x300/0x340
Modules linked in: hwmon mdio_i2c crypto_safexcel(+) md5 sha256_generic libsha256 authenc libdes omap_rng rng_core nft_masq nft_nat nft_chain_nat nf_nat nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables libcrc32c nfnetlink fuse autofs4
CPU: 1 PID: 232 Comm: systemd-udevd Tainted: G W 6.1.6-00002-g9d4898824677 #3
Hardware name: MikroTik RB5009 (DT)
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : free_irq+0x300/0x340
lr : free_irq+0x2e0/0x340
sp : ffff800008fa3890
x29: ffff800008fa3890 x28: 0000000000000000 x27: 0000000000000000
x26: ffff8000008e6dc0 x25: ffff000009034cac x24: ffff000009034d50
x23: 0000000000000000 x22: 000000000000004a x21: ffff0000093e0d80
x20: ffff000009034c00 x19: ffff00000615fc00 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 000075f5c1584c5e
x14: 0000000000000017 x13: 0000000000000000 x12: 0000000000000040
x11: ffff000000579b60 x10: ffff000000579b62 x9 : ffff800008bbe370
x8 : ffff000000579dd0 x7 : 0000000000000000 x6 : ffff000000579e18
x5 : ffff000000579da8 x4 : ffff800008ca0000 x3 : ffff800008ca0188
x2 : 0000000013033204 x1 : ffff000009034c00 x0 : ffff8000087eadf0
Call trace:
free_irq+0x300/0x340
devm_irq_release+0x14/0x20
devres_release_all+0xa0/0x100
device_unbind_cleanup+0x14/0x60
really_probe+0x198/0x2d4
__driver_probe_device+0x74/0xdc
driver_probe_device+0x3c/0x110
__driver_attach+0x8c/0x190
bus_for_each_dev+0x6c/0xc0
driver_attach+0x20/0x30
bus_add_driver+0x148/0x1fc
driver_register+0x74/0x120
__platform_driver_register+0x24/0x30
safexcel_init+0x48/0x1000 [crypto_safexcel]
do_one_initcall+0x4c/0x1b0
do_init_module+0x44/0x1cc
load_module+0x1724/0x1be4
__do_sys_finit_module+0xbc/0x110
__arm64_sys_finit_module+0x1c/0x24
invoke_syscall+0x44/0x110
el0_svc_common.constprop.0+0xc0/0xe0
do_el0_svc+0x20/0x80
el0_svc+0x14/0x4c
el0t_64_sync_handler+0xb0/0xb4
el0t_64_sync+0x148/0x14c
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: Fix memory leak when handling surveys
When removing a rt2x00 device, its associated channel surveys
are not freed, causing a memory leak observable with kmemleak:
unreferenced object 0xffff9620f0881a00 (size 512):
comm "systemd-udevd", pid 2290, jiffies 4294906974 (age 33.768s)
hex dump (first 32 bytes):
70 44 12 00 00 00 00 00 92 8a 00 00 00 00 00 00 pD..............
00 00 00 00 00 00 00 00 ab 87 01 00 00 00 00 00 ................
backtrace:
[<ffffffffb0ed858b>] __kmalloc+0x4b/0x130
[<ffffffffc1b0f29b>] rt2800_probe_hw+0xc2b/0x1380 [rt2800lib]
[<ffffffffc1a9496e>] rt2800usb_probe_hw+0xe/0x60 [rt2800usb]
[<ffffffffc1ae491a>] rt2x00lib_probe_dev+0x21a/0x7d0 [rt2x00lib]
[<ffffffffc1b3b83e>] rt2x00usb_probe+0x1be/0x980 [rt2x00usb]
[<ffffffffc05981e2>] usb_probe_interface+0xe2/0x310 [usbcore]
[<ffffffffb13be2d5>] really_probe+0x1a5/0x410
[<ffffffffb13be5c8>] __driver_probe_device+0x78/0x180
[<ffffffffb13be6fe>] driver_probe_device+0x1e/0x90
[<ffffffffb13be972>] __driver_attach+0xd2/0x1c0
[<ffffffffb13bbc57>] bus_for_each_dev+0x77/0xd0
[<ffffffffb13bd2a2>] bus_add_driver+0x112/0x210
[<ffffffffb13bfc6c>] driver_register+0x5c/0x120
[<ffffffffc0596ae8>] usb_register_driver+0x88/0x150 [usbcore]
[<ffffffffb0c011c4>] do_one_initcall+0x44/0x220
[<ffffffffb0d6134c>] do_init_module+0x4c/0x220
Fix this by freeing the channel surveys on device removal.
Tested with a RT3070 based USB wireless adapter. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: stop parsing non-compact HEAD index if clusterofs is invalid
Syzbot generated a crafted image [1] with a non-compact HEAD index of
clusterofs 33024 while valid numbers should be 0 ~ lclustersize-1,
which causes the following unexpected behavior as below:
BUG: unable to handle page fault for address: fffff52101a3fff9
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 23ffed067 P4D 23ffed067 PUD 0
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 4398 Comm: kworker/u5:1 Not tainted 6.3.0-rc6-syzkaller-g09a9639e56c0 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/30/2023
Workqueue: erofs_worker z_erofs_decompressqueue_work
RIP: 0010:z_erofs_decompress_queue+0xb7e/0x2b40
...
Call Trace:
<TASK>
z_erofs_decompressqueue_work+0x99/0xe0
process_one_work+0x8f6/0x1170
worker_thread+0xa63/0x1210
kthread+0x270/0x300
ret_from_fork+0x1f/0x30
Note that normal images or images using compact indexes are not
impacted. Let's fix this now.
[1] https://lore.kernel.org/r/000000000000ec75b005ee97fbaa@google.com |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/type1: fix cap_migration information leak
Fix an information leak where an uninitialized hole in struct
vfio_iommu_type1_info_cap_migration on the stack is exposed to userspace.
The definition of struct vfio_iommu_type1_info_cap_migration contains a hole as
shown in this pahole(1) output:
struct vfio_iommu_type1_info_cap_migration {
struct vfio_info_cap_header header; /* 0 8 */
__u32 flags; /* 8 4 */
/* XXX 4 bytes hole, try to pack */
__u64 pgsize_bitmap; /* 16 8 */
__u64 max_dirty_bitmap_size; /* 24 8 */
/* size: 32, cachelines: 1, members: 4 */
/* sum members: 28, holes: 1, sum holes: 4 */
/* last cacheline: 32 bytes */
};
The cap_mig variable is filled in without initializing the hole:
static int vfio_iommu_migration_build_caps(struct vfio_iommu *iommu,
struct vfio_info_cap *caps)
{
struct vfio_iommu_type1_info_cap_migration cap_mig;
cap_mig.header.id = VFIO_IOMMU_TYPE1_INFO_CAP_MIGRATION;
cap_mig.header.version = 1;
cap_mig.flags = 0;
/* support minimum pgsize */
cap_mig.pgsize_bitmap = (size_t)1 << __ffs(iommu->pgsize_bitmap);
cap_mig.max_dirty_bitmap_size = DIRTY_BITMAP_SIZE_MAX;
return vfio_info_add_capability(caps, &cap_mig.header, sizeof(cap_mig));
}
The structure is then copied to a temporary location on the heap. At this point
it's already too late and ioctl(VFIO_IOMMU_GET_INFO) copies it to userspace
later:
int vfio_info_add_capability(struct vfio_info_cap *caps,
struct vfio_info_cap_header *cap, size_t size)
{
struct vfio_info_cap_header *header;
header = vfio_info_cap_add(caps, size, cap->id, cap->version);
if (IS_ERR(header))
return PTR_ERR(header);
memcpy(header + 1, cap + 1, size - sizeof(*header));
return 0;
}
This issue was found by code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: Add missing hw_ops->get_ring_selector() for IPQ5018
During sending data after clients connected, hw_ops->get_ring_selector()
will be called. But for IPQ5018, this member isn't set, and the
following NULL pointer exception will be occurred:
[ 38.840478] 8<--- cut here ---
[ 38.840517] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 38.923161] PC is at 0x0
[ 38.927930] LR is at ath11k_dp_tx+0x70/0x730 [ath11k]
...
[ 39.063264] Process hostapd (pid: 1034, stack limit = 0x801ceb3d)
[ 39.068994] Stack: (0x856a9a68 to 0x856aa000)
...
[ 39.438467] [<7f323804>] (ath11k_dp_tx [ath11k]) from [<7f314e6c>] (ath11k_mac_op_tx+0x80/0x190 [ath11k])
[ 39.446607] [<7f314e6c>] (ath11k_mac_op_tx [ath11k]) from [<7f17dbe0>] (ieee80211_handle_wake_tx_queue+0x7c/0xc0 [mac80211])
[ 39.456162] [<7f17dbe0>] (ieee80211_handle_wake_tx_queue [mac80211]) from [<7f174450>] (ieee80211_probereq_get+0x584/0x704 [mac80211])
[ 39.467443] [<7f174450>] (ieee80211_probereq_get [mac80211]) from [<7f178c40>] (ieee80211_tx_prepare_skb+0x1f8/0x248 [mac80211])
[ 39.479334] [<7f178c40>] (ieee80211_tx_prepare_skb [mac80211]) from [<7f179e28>] (__ieee80211_subif_start_xmit+0x32c/0x3d4 [mac80211])
[ 39.491053] [<7f179e28>] (__ieee80211_subif_start_xmit [mac80211]) from [<7f17af08>] (ieee80211_tx_control_port+0x19c/0x288 [mac80211])
[ 39.502946] [<7f17af08>] (ieee80211_tx_control_port [mac80211]) from [<7f0fc704>] (nl80211_tx_control_port+0x174/0x1d4 [cfg80211])
[ 39.515017] [<7f0fc704>] (nl80211_tx_control_port [cfg80211]) from [<808ceac4>] (genl_rcv_msg+0x154/0x340)
[ 39.526814] [<808ceac4>] (genl_rcv_msg) from [<808cdb74>] (netlink_rcv_skb+0xb8/0x11c)
[ 39.536446] [<808cdb74>] (netlink_rcv_skb) from [<808ce1d0>] (genl_rcv+0x28/0x34)
[ 39.544344] [<808ce1d0>] (genl_rcv) from [<808cd234>] (netlink_unicast+0x174/0x274)
[ 39.551895] [<808cd234>] (netlink_unicast) from [<808cd510>] (netlink_sendmsg+0x1dc/0x440)
[ 39.559362] [<808cd510>] (netlink_sendmsg) from [<808596e0>] (____sys_sendmsg+0x1a8/0x1fc)
[ 39.567697] [<808596e0>] (____sys_sendmsg) from [<8085b1a8>] (___sys_sendmsg+0xa4/0xdc)
[ 39.575941] [<8085b1a8>] (___sys_sendmsg) from [<8085b310>] (sys_sendmsg+0x44/0x74)
[ 39.583841] [<8085b310>] (sys_sendmsg) from [<80300060>] (ret_fast_syscall+0x0/0x40)
...
[ 39.620734] Code: bad PC value
[ 39.625869] ---[ end trace 8aef983ad3cbc032 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Fix kernel warning during topology setup
This patch fixes the following kernel warning seen during
driver load by correctly initializing the p2plink attr before
creating the sysfs file:
[ +0.002865] ------------[ cut here ]------------
[ +0.002327] kobject: '(null)' (0000000056260cfb): is not initialized, yet kobject_put() is being called.
[ +0.004780] WARNING: CPU: 32 PID: 1006 at lib/kobject.c:718 kobject_put+0xaa/0x1c0
[ +0.001361] Call Trace:
[ +0.001234] <TASK>
[ +0.001067] kfd_remove_sysfs_node_entry+0x24a/0x2d0 [amdgpu]
[ +0.003147] kfd_topology_update_sysfs+0x3d/0x750 [amdgpu]
[ +0.002890] kfd_topology_add_device+0xbd7/0xc70 [amdgpu]
[ +0.002844] ? lock_release+0x13c/0x2e0
[ +0.001936] ? smu_cmn_send_smc_msg_with_param+0x1e8/0x2d0 [amdgpu]
[ +0.003313] ? amdgpu_dpm_get_mclk+0x54/0x60 [amdgpu]
[ +0.002703] kgd2kfd_device_init.cold+0x39f/0x4ed [amdgpu]
[ +0.002930] amdgpu_amdkfd_device_init+0x13d/0x1f0 [amdgpu]
[ +0.002944] amdgpu_device_init.cold+0x1464/0x17b4 [amdgpu]
[ +0.002970] ? pci_bus_read_config_word+0x43/0x80
[ +0.002380] amdgpu_driver_load_kms+0x15/0x100 [amdgpu]
[ +0.002744] amdgpu_pci_probe+0x147/0x370 [amdgpu]
[ +0.002522] local_pci_probe+0x40/0x80
[ +0.001896] work_for_cpu_fn+0x10/0x20
[ +0.001892] process_one_work+0x26e/0x5a0
[ +0.002029] worker_thread+0x1fd/0x3e0
[ +0.001890] ? process_one_work+0x5a0/0x5a0
[ +0.002115] kthread+0xea/0x110
[ +0.001618] ? kthread_complete_and_exit+0x20/0x20
[ +0.002422] ret_from_fork+0x1f/0x30
[ +0.001808] </TASK>
[ +0.001103] irq event stamp: 59837
[ +0.001718] hardirqs last enabled at (59849): [<ffffffffb30fab12>] __up_console_sem+0x52/0x60
[ +0.004414] hardirqs last disabled at (59860): [<ffffffffb30faaf7>] __up_console_sem+0x37/0x60
[ +0.004414] softirqs last enabled at (59654): [<ffffffffb307d9c7>] irq_exit_rcu+0xd7/0x130
[ +0.004205] softirqs last disabled at (59649): [<ffffffffb307d9c7>] irq_exit_rcu+0xd7/0x130
[ +0.004203] ---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: Fix system crash due to lack of free space in LFS
When f2fs tries to checkpoint during foreground gc in LFS mode, system
crash occurs due to lack of free space if the amount of dirty node and
dentry pages generated by data migration exceeds free space.
The reproduction sequence is as follows.
- 20GiB capacity block device (null_blk)
- format and mount with LFS mode
- create a file and write 20,000MiB
- 4k random write on full range of the file
RIP: 0010:new_curseg+0x48a/0x510 [f2fs]
Code: 55 e7 f5 89 c0 48 0f af c3 48 8b 5d c0 48 c1 e8 20 83 c0 01 89 43 6c 48 83 c4 28 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc <0f> 0b f0 41 80 4f 48 04 45 85 f6 0f 84 ba fd ff ff e9 ef fe ff ff
RSP: 0018:ffff977bc397b218 EFLAGS: 00010246
RAX: 00000000000027b9 RBX: 0000000000000000 RCX: 00000000000027c0
RDX: 0000000000000000 RSI: 00000000000027b9 RDI: ffff8c25ab4e74f8
RBP: ffff977bc397b268 R08: 00000000000027b9 R09: ffff8c29e4a34b40
R10: 0000000000000001 R11: ffff977bc397b0d8 R12: 0000000000000000
R13: ffff8c25b4dd81a0 R14: 0000000000000000 R15: ffff8c2f667f9000
FS: 0000000000000000(0000) GS:ffff8c344ec80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000c00055d000 CR3: 0000000e30810003 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
allocate_segment_by_default+0x9c/0x110 [f2fs]
f2fs_allocate_data_block+0x243/0xa30 [f2fs]
? __mod_lruvec_page_state+0xa0/0x150
do_write_page+0x80/0x160 [f2fs]
f2fs_do_write_node_page+0x32/0x50 [f2fs]
__write_node_page+0x339/0x730 [f2fs]
f2fs_sync_node_pages+0x5a6/0x780 [f2fs]
block_operations+0x257/0x340 [f2fs]
f2fs_write_checkpoint+0x102/0x1050 [f2fs]
f2fs_gc+0x27c/0x630 [f2fs]
? folio_mark_dirty+0x36/0x70
f2fs_balance_fs+0x16f/0x180 [f2fs]
This patch adds checking whether free sections are enough before checkpoint
during gc.
[Jaegeuk Kim: code clean-up] |
| In the Linux kernel, the following vulnerability has been resolved:
can: j1939: prevent deadlock by moving j1939_sk_errqueue()
This commit addresses a deadlock situation that can occur in certain
scenarios, such as when running data TP/ETP transfer and subscribing to
the error queue while receiving a net down event. The deadlock involves
locks in the following order:
3
j1939_session_list_lock -> active_session_list_lock
j1939_session_activate
...
j1939_sk_queue_activate_next -> sk_session_queue_lock
...
j1939_xtp_rx_eoma_one
2
j1939_sk_queue_drop_all -> sk_session_queue_lock
...
j1939_sk_netdev_event_netdown -> j1939_socks_lock
j1939_netdev_notify
1
j1939_sk_errqueue -> j1939_socks_lock
__j1939_session_cancel -> active_session_list_lock
j1939_tp_rxtimer
CPU0 CPU1
---- ----
lock(&priv->active_session_list_lock);
lock(&jsk->sk_session_queue_lock);
lock(&priv->active_session_list_lock);
lock(&priv->j1939_socks_lock);
The solution implemented in this commit is to move the
j1939_sk_errqueue() call out of the active_session_list_lock context,
thus preventing the deadlock situation. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: core: Fix target_cmd_counter leak
The target_cmd_counter struct allocated via target_alloc_cmd_counter() is
never freed, resulting in leaks across various transport types, e.g.:
unreferenced object 0xffff88801f920120 (size 96):
comm "sh", pid 102, jiffies 4294892535 (age 713.412s)
hex dump (first 32 bytes):
07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 38 01 92 1f 80 88 ff ff ........8.......
backtrace:
[<00000000e58a6252>] kmalloc_trace+0x11/0x20
[<0000000043af4b2f>] target_alloc_cmd_counter+0x17/0x90 [target_core_mod]
[<000000007da2dfa7>] target_setup_session+0x2d/0x140 [target_core_mod]
[<0000000068feef86>] tcm_loop_tpg_nexus_store+0x19b/0x350 [tcm_loop]
[<000000006a80e021>] configfs_write_iter+0xb1/0x120
[<00000000e9f4d860>] vfs_write+0x2e4/0x3c0
[<000000008143433b>] ksys_write+0x80/0xb0
[<00000000a7df29b2>] do_syscall_64+0x42/0x90
[<0000000053f45fb8>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Free the structure alongside the corresponding iscsit_conn / se_sess
parent. |
| In the Linux kernel, the following vulnerability has been resolved:
net: core: remove unnecessary frame_sz check in bpf_xdp_adjust_tail()
Syzkaller reported the following issue:
=======================================
Too BIG xdp->frame_sz = 131072
WARNING: CPU: 0 PID: 5020 at net/core/filter.c:4121
____bpf_xdp_adjust_tail net/core/filter.c:4121 [inline]
WARNING: CPU: 0 PID: 5020 at net/core/filter.c:4121
bpf_xdp_adjust_tail+0x466/0xa10 net/core/filter.c:4103
...
Call Trace:
<TASK>
bpf_prog_4add87e5301a4105+0x1a/0x1c
__bpf_prog_run include/linux/filter.h:600 [inline]
bpf_prog_run_xdp include/linux/filter.h:775 [inline]
bpf_prog_run_generic_xdp+0x57e/0x11e0 net/core/dev.c:4721
netif_receive_generic_xdp net/core/dev.c:4807 [inline]
do_xdp_generic+0x35c/0x770 net/core/dev.c:4866
tun_get_user+0x2340/0x3ca0 drivers/net/tun.c:1919
tun_chr_write_iter+0xe8/0x210 drivers/net/tun.c:2043
call_write_iter include/linux/fs.h:1871 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x650/0xe40 fs/read_write.c:584
ksys_write+0x12f/0x250 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x38/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
xdp->frame_sz > PAGE_SIZE check was introduced in commit c8741e2bfe87
("xdp: Allow bpf_xdp_adjust_tail() to grow packet size"). But Jesper
Dangaard Brouer <jbrouer@redhat.com> noted that after introducing the
xdp_init_buff() which all XDP driver use - it's safe to remove this
check. The original intend was to catch cases where XDP drivers have
not been updated to use xdp.frame_sz, but that is not longer a concern
(since xdp_init_buff).
Running the initial syzkaller repro it was discovered that the
contiguous physical memory allocation is used for both xdp paths in
tun_get_user(), e.g. tun_build_skb() and tun_alloc_skb(). It was also
stated by Jesper Dangaard Brouer <jbrouer@redhat.com> that XDP can
work on higher order pages, as long as this is contiguous physical
memory (e.g. a page). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: don't free qgroup space unless specified
Boris noticed in his simple quotas testing that he was getting a leak
with Sweet Tea's change to subvol create that stopped doing a
transaction commit. This was just a side effect of that change.
In the delayed inode code we have an optimization that will free extra
reservations if we think we can pack a dir item into an already modified
leaf. Previously this wouldn't be triggered in the subvolume create
case because we'd commit the transaction, it was still possible but
much harder to trigger. It could actually be triggered if we did a
mkdir && subvol create with qgroups enabled.
This occurs because in btrfs_insert_delayed_dir_index(), which gets
called when we're adding the dir item, we do the following:
btrfs_block_rsv_release(fs_info, trans->block_rsv, bytes, NULL);
if we're able to skip reserving space.
The problem here is that trans->block_rsv points at the temporary block
rsv for the subvolume create, which has qgroup reservations in the block
rsv.
This is a problem because btrfs_block_rsv_release() will do the
following:
if (block_rsv->qgroup_rsv_reserved >= block_rsv->qgroup_rsv_size) {
qgroup_to_release = block_rsv->qgroup_rsv_reserved -
block_rsv->qgroup_rsv_size;
block_rsv->qgroup_rsv_reserved = block_rsv->qgroup_rsv_size;
}
The temporary block rsv just has ->qgroup_rsv_reserved set,
->qgroup_rsv_size == 0. The optimization in
btrfs_insert_delayed_dir_index() sets ->qgroup_rsv_reserved = 0. Then
later on when we call btrfs_subvolume_release_metadata() which has
btrfs_block_rsv_release(fs_info, rsv, (u64)-1, &qgroup_to_release);
btrfs_qgroup_convert_reserved_meta(root, qgroup_to_release);
qgroup_to_release is set to 0, and we do not convert the reserved
metadata space.
The problem here is that the block rsv code has been unconditionally
messing with ->qgroup_rsv_reserved, because the main place this is used
is delalloc, and any time we call btrfs_block_rsv_release() we do it
with qgroup_to_release set, and thus do the proper accounting.
The subvolume code is the only other code that uses the qgroup
reservation stuff, but it's intermingled with the above optimization,
and thus was getting its reservation freed out from underneath it and
thus leaking the reserved space.
The solution is to simply not mess with the qgroup reservations if we
don't have qgroup_to_release set. This works with the existing code as
anything that messes with the delalloc reservations always have
qgroup_to_release set. This fixes the leak that Boris was observing. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix memory leak of iter->temp when reading trace_pipe
kmemleak reports:
unreferenced object 0xffff88814d14e200 (size 256):
comm "cat", pid 336, jiffies 4294871818 (age 779.490s)
hex dump (first 32 bytes):
04 00 01 03 00 00 00 00 08 00 00 00 00 00 00 00 ................
0c d8 c8 9b ff ff ff ff 04 5a ca 9b ff ff ff ff .........Z......
backtrace:
[<ffffffff9bdff18f>] __kmalloc+0x4f/0x140
[<ffffffff9bc9238b>] trace_find_next_entry+0xbb/0x1d0
[<ffffffff9bc9caef>] trace_print_lat_context+0xaf/0x4e0
[<ffffffff9bc94490>] print_trace_line+0x3e0/0x950
[<ffffffff9bc95499>] tracing_read_pipe+0x2d9/0x5a0
[<ffffffff9bf03a43>] vfs_read+0x143/0x520
[<ffffffff9bf04c2d>] ksys_read+0xbd/0x160
[<ffffffff9d0f0edf>] do_syscall_64+0x3f/0x90
[<ffffffff9d2000aa>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
when reading file 'trace_pipe', 'iter->temp' is allocated or relocated
in trace_find_next_entry() but not freed before 'trace_pipe' is closed.
To fix it, free 'iter->temp' in tracing_release_pipe(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Disable preemption in bpf_event_output
We received report [1] of kernel crash, which is caused by
using nesting protection without disabled preemption.
The bpf_event_output can be called by programs executed by
bpf_prog_run_array_cg function that disabled migration but
keeps preemption enabled.
This can cause task to be preempted by another one inside the
nesting protection and lead eventually to two tasks using same
perf_sample_data buffer and cause crashes like:
BUG: kernel NULL pointer dereference, address: 0000000000000001
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
...
? perf_output_sample+0x12a/0x9a0
? finish_task_switch.isra.0+0x81/0x280
? perf_event_output+0x66/0xa0
? bpf_event_output+0x13a/0x190
? bpf_event_output_data+0x22/0x40
? bpf_prog_dfc84bbde731b257_cil_sock4_connect+0x40a/0xacb
? xa_load+0x87/0xe0
? __cgroup_bpf_run_filter_sock_addr+0xc1/0x1a0
? release_sock+0x3e/0x90
? sk_setsockopt+0x1a1/0x12f0
? udp_pre_connect+0x36/0x50
? inet_dgram_connect+0x93/0xa0
? __sys_connect+0xb4/0xe0
? udp_setsockopt+0x27/0x40
? __pfx_udp_push_pending_frames+0x10/0x10
? __sys_setsockopt+0xdf/0x1a0
? __x64_sys_connect+0xf/0x20
? do_syscall_64+0x3a/0x90
? entry_SYSCALL_64_after_hwframe+0x72/0xdc
Fixing this by disabling preemption in bpf_event_output.
[1] https://github.com/cilium/cilium/issues/26756 |
