| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: validate the extent length for uncompressed pclusters
syzkaller reported a KASAN use-after-free:
https://syzkaller.appspot.com/bug?extid=2ae90e873e97f1faf6f2
The referenced fuzzed image actually has two issues:
- m_pa == 0 as a non-inlined pcluster;
- The logical length is longer than its physical length.
The first issue has already been addressed. This patch addresses
the second issue by checking the extent length validity. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Add a length limitation for the ivrs_acpihid command-line parameter
The 'acpiid' buffer in the parse_ivrs_acpihid function may overflow,
because the string specifier in the format string sscanf()
has no width limitation.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8192u: Fix use after free in ieee80211_rx()
We cannot dereference the "skb" pointer after calling
ieee80211_monitor_rx(), because it is a use after free. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: fix memory leak in bnxt_nvm_test()
Free the kzalloc'ed buffer before returning in the success path. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: Fix resource leak in ksmbd_session_rpc_open()
When ksmbd_rpc_open() fails then it must call ksmbd_rpc_id_free() to
undo the result of ksmbd_ipc_id_alloc(). |
| In the Linux kernel, the following vulnerability has been resolved:
media: ipu3-imgu: Fix NULL pointer dereference in active selection access
What the IMGU driver did was that it first acquired the pointers to active
and try V4L2 subdev state, and only then figured out which one to use.
The problem with that approach and a later patch (see Fixes: tag) is that
as sd_state argument to v4l2_subdev_get_try_crop() et al is NULL, there is
now an attempt to dereference that.
Fix this.
Also rewrap lines a little. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: skip splitting and logical rewriting on pre-alloc write
When doing a relocation, there is a chance that at the time of
btrfs_reloc_clone_csums(), there is no checksum for the corresponding
region.
In this case, btrfs_finish_ordered_zoned()'s sum points to an invalid item
and so ordered_extent's logical is set to some invalid value. Then,
btrfs_lookup_block_group() in btrfs_zone_finish_endio() failed to find a
block group and will hit an assert or a null pointer dereference as
following.
This can be reprodcued by running btrfs/028 several times (e.g, 4 to 16
times) with a null_blk setup. The device's zone size and capacity is set to
32 MB and the storage size is set to 5 GB on my setup.
KASAN: null-ptr-deref in range [0x0000000000000088-0x000000000000008f]
CPU: 6 PID: 3105720 Comm: kworker/u16:13 Tainted: G W 6.5.0-rc6-kts+ #1
Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0 12/17/2015
Workqueue: btrfs-endio-write btrfs_work_helper [btrfs]
RIP: 0010:btrfs_zone_finish_endio.part.0+0x34/0x160 [btrfs]
Code: 41 54 49 89 fc 55 48 89 f5 53 e8 57 7d fc ff 48 8d b8 88 00 00 00 48 89 c3 48 b8 00 00 00 00 00
> 3c 02 00 0f 85 02 01 00 00 f6 83 88 00 00 00 01 0f 84 a8 00 00
RSP: 0018:ffff88833cf87b08 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000011 RSI: 0000000000000004 RDI: 0000000000000088
RBP: 0000000000000002 R08: 0000000000000001 R09: ffffed102877b827
R10: ffff888143bdc13b R11: ffff888125b1cbc0 R12: ffff888143bdc000
R13: 0000000000007000 R14: ffff888125b1cba8 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88881e500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3ed85223d5 CR3: 00000001519b4005 CR4: 00000000001706e0
Call Trace:
<TASK>
? die_addr+0x3c/0xa0
? exc_general_protection+0x148/0x220
? asm_exc_general_protection+0x22/0x30
? btrfs_zone_finish_endio.part.0+0x34/0x160 [btrfs]
? btrfs_zone_finish_endio.part.0+0x19/0x160 [btrfs]
btrfs_finish_one_ordered+0x7b8/0x1de0 [btrfs]
? rcu_is_watching+0x11/0xb0
? lock_release+0x47a/0x620
? btrfs_finish_ordered_zoned+0x59b/0x800 [btrfs]
? __pfx_btrfs_finish_one_ordered+0x10/0x10 [btrfs]
? btrfs_finish_ordered_zoned+0x358/0x800 [btrfs]
? __smp_call_single_queue+0x124/0x350
? rcu_is_watching+0x11/0xb0
btrfs_work_helper+0x19f/0xc60 [btrfs]
? __pfx_try_to_wake_up+0x10/0x10
? _raw_spin_unlock_irq+0x24/0x50
? rcu_is_watching+0x11/0xb0
process_one_work+0x8c1/0x1430
? __pfx_lock_acquire+0x10/0x10
? __pfx_process_one_work+0x10/0x10
? __pfx_do_raw_spin_lock+0x10/0x10
? _raw_spin_lock_irq+0x52/0x60
worker_thread+0x100/0x12c0
? __kthread_parkme+0xc1/0x1f0
? __pfx_worker_thread+0x10/0x10
kthread+0x2ea/0x3c0
? __pfx_kthread+0x10/0x10
ret_from_fork+0x30/0x70
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
On the zoned mode, writing to pre-allocated region means data relocation
write. Such write always uses WRITE command so there is no need of splitting
and rewriting logical address. Thus, we can just skip the function for the
case. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: rockchip: Fix refcount leak in rockchip_pinctrl_parse_groups
of_find_node_by_phandle() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
kheaders: Use array declaration instead of char
Under CONFIG_FORTIFY_SOURCE, memcpy() will check the size of destination
and source buffers. Defining kernel_headers_data as "char" would trip
this check. Since these addresses are treated as byte arrays, define
them as arrays (as done everywhere else).
This was seen with:
$ cat /sys/kernel/kheaders.tar.xz >> /dev/null
detected buffer overflow in memcpy
kernel BUG at lib/string_helpers.c:1027!
...
RIP: 0010:fortify_panic+0xf/0x20
[...]
Call Trace:
<TASK>
ikheaders_read+0x45/0x50 [kheaders]
kernfs_fop_read_iter+0x1a4/0x2f0
... |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_ffa: Check if ffa_driver remove is present before executing
Currently ffa_drv->remove() is called unconditionally from
ffa_device_remove(). Since the driver registration doesn't check for it
and allows it to be registered without .remove callback, we need to check
for the presence of it before executing it from ffa_device_remove() to
above a NULL pointer dereference like the one below:
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
| Mem abort info:
| ESR = 0x0000000086000004
| EC = 0x21: IABT (current EL), IL = 32 bits
| SET = 0, FnV = 0
| EA = 0, S1PTW = 0
| FSC = 0x04: level 0 translation fault
| user pgtable: 4k pages, 48-bit VAs, pgdp=0000000881cc8000
| [0000000000000000] pgd=0000000000000000, p4d=0000000000000000
| Internal error: Oops: 0000000086000004 [#1] PREEMPT SMP
| CPU: 3 PID: 130 Comm: rmmod Not tainted 6.3.0-rc7 #6
| Hardware name: FVP Base RevC (DT)
| pstate: 63402809 (nZCv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=-c)
| pc : 0x0
| lr : ffa_device_remove+0x20/0x2c
| Call trace:
| 0x0
| device_release_driver_internal+0x16c/0x260
| driver_detach+0x90/0xd0
| bus_remove_driver+0xdc/0x11c
| driver_unregister+0x30/0x54
| ffa_driver_unregister+0x14/0x20
| cleanup_module+0x18/0xeec
| __arm64_sys_delete_module+0x234/0x378
| invoke_syscall+0x40/0x108
| el0_svc_common+0xb4/0xf0
| do_el0_svc+0x30/0xa4
| el0_svc+0x2c/0x7c
| el0t_64_sync_handler+0x84/0xf0
| el0t_64_sync+0x190/0x194 |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: use proper req destructor for IPv6
Before, only the destructor from TCP request sock in IPv4 was called
even if the subflow was IPv6.
It is important to use the right destructor to avoid memory leaks with
some advanced IPv6 features, e.g. when the request socks contain
specific IPv6 options. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Set end correctly when doing batch carry
Even though the test suite covers this it somehow became obscured that
this wasn't working.
The test iommufd_ioas.mock_domain.access_domain_destory would blow up
rarely.
end should be set to 1 because this just pushed an item, the carry, to the
pfns list.
Sometimes the test would blow up with:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP
CPU: 5 PID: 584 Comm: iommufd Not tainted 6.5.0-rc1-dirty #1236
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:batch_unpin+0xa2/0x100 [iommufd]
Code: 17 48 81 fe ff ff 07 00 77 70 48 8b 15 b7 be 97 e2 48 85 d2 74 14 48 8b 14 fa 48 85 d2 74 0b 40 0f b6 f6 48 c1 e6 04 48 01 f2 <48> 8b 3a 48 c1 e0 06 89 ca 48 89 de 48 83 e7 f0 48 01 c7 e8 96 dc
RSP: 0018:ffffc90001677a58 EFLAGS: 00010246
RAX: 00007f7e2646f000 RBX: 0000000000000000 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 00000000fefc4c8d RDI: 0000000000fefc4c
RBP: ffffc90001677a80 R08: 0000000000000048 R09: 0000000000000200
R10: 0000000000030b98 R11: ffffffff81f3bb40 R12: 0000000000000001
R13: ffff888101f75800 R14: ffffc90001677ad0 R15: 00000000000001fe
FS: 00007f9323679740(0000) GS:ffff8881ba540000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000105ede003 CR4: 00000000003706a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? show_regs+0x5c/0x70
? __die+0x1f/0x60
? page_fault_oops+0x15d/0x440
? lock_release+0xbc/0x240
? exc_page_fault+0x4a4/0x970
? asm_exc_page_fault+0x27/0x30
? batch_unpin+0xa2/0x100 [iommufd]
? batch_unpin+0xba/0x100 [iommufd]
__iopt_area_unfill_domain+0x198/0x430 [iommufd]
? __mutex_lock+0x8c/0xb80
? __mutex_lock+0x6aa/0xb80
? xa_erase+0x28/0x30
? iopt_table_remove_domain+0x162/0x320 [iommufd]
? lock_release+0xbc/0x240
iopt_area_unfill_domain+0xd/0x10 [iommufd]
iopt_table_remove_domain+0x195/0x320 [iommufd]
iommufd_hw_pagetable_destroy+0xb3/0x110 [iommufd]
iommufd_object_destroy_user+0x8e/0xf0 [iommufd]
iommufd_device_detach+0xc5/0x140 [iommufd]
iommufd_selftest_destroy+0x1f/0x70 [iommufd]
iommufd_object_destroy_user+0x8e/0xf0 [iommufd]
iommufd_destroy+0x3a/0x50 [iommufd]
iommufd_fops_ioctl+0xfb/0x170 [iommufd]
__x64_sys_ioctl+0x40d/0x9a0
do_syscall_64+0x3c/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
clk: visconti: Fix memory leak in visconti_register_pll()
@pll->rate_table has allocated memory by kmemdup(), if clk_hw_register()
fails, it should be freed, otherwise it will cause memory leak issue,
this patch fixes it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: realtek: fix out-of-bounds access
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/xen: Fix memory leak in xen_init_lock_cpu()
In xen_init_lock_cpu(), the @name has allocated new string by kasprintf(),
if bind_ipi_to_irqhandler() fails, it should be freed, otherwise may lead
to a memory leak issue, fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: media: tegra-video: fix device_node use after free
At probe time this code path is followed:
* tegra_csi_init
* tegra_csi_channels_alloc
* for_each_child_of_node(node, channel) -- iterates over channels
* automatically gets 'channel'
* tegra_csi_channel_alloc()
* saves into chan->of_node a pointer to the channel OF node
* automatically gets and puts 'channel'
* now the node saved in chan->of_node has refcount 0, can disappear
* tegra_csi_channels_init
* iterates over channels
* tegra_csi_channel_init -- uses chan->of_node
After that, chan->of_node keeps storing the node until the device is
removed.
of_node_get() the node and of_node_put() it during teardown to avoid any
risk. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: stm32-pwr: fix of_iomap leak
Smatch reports:
drivers/regulator/stm32-pwr.c:166 stm32_pwr_regulator_probe() warn:
'base' from of_iomap() not released on lines: 151,166.
In stm32_pwr_regulator_probe(), base is not released
when devm_kzalloc() fails to allocate memory or
devm_regulator_register() fails to register a new regulator device,
which may cause a leak.
To fix this issue, replace of_iomap() with
devm_platform_ioremap_resource(). devm_platform_ioremap_resource()
is a specialized function for platform devices.
It allows 'base' to be automatically released whether the probe
function succeeds or fails.
Besides, use IS_ERR(base) instead of !base
as the return value of devm_platform_ioremap_resource()
can either be a pointer to the remapped memory or
an ERR_PTR() encoded error code if the operation fails. |
| In the Linux kernel, the following vulnerability has been resolved:
isdn: mISDN: hfcsusb: fix memory leak in hfcsusb_probe()
In hfcsusb_probe(), the memory allocated for ctrl_urb gets leaked when
setup_instance() fails with an error code. Fix that by freeing the urb
before freeing the hw structure. Also change the error paths to use the
goto ladder style.
Compile tested only. Issue found using a prototype static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
audit: fix possible soft lockup in __audit_inode_child()
Tracefs or debugfs maybe cause hundreds to thousands of PATH records,
too many PATH records maybe cause soft lockup.
For example:
1. CONFIG_KASAN=y && CONFIG_PREEMPTION=n
2. auditctl -a exit,always -S open -k key
3. sysctl -w kernel.watchdog_thresh=5
4. mkdir /sys/kernel/debug/tracing/instances/test
There may be a soft lockup as follows:
watchdog: BUG: soft lockup - CPU#45 stuck for 7s! [mkdir:15498]
Kernel panic - not syncing: softlockup: hung tasks
Call trace:
dump_backtrace+0x0/0x30c
show_stack+0x20/0x30
dump_stack+0x11c/0x174
panic+0x27c/0x494
watchdog_timer_fn+0x2bc/0x390
__run_hrtimer+0x148/0x4fc
__hrtimer_run_queues+0x154/0x210
hrtimer_interrupt+0x2c4/0x760
arch_timer_handler_phys+0x48/0x60
handle_percpu_devid_irq+0xe0/0x340
__handle_domain_irq+0xbc/0x130
gic_handle_irq+0x78/0x460
el1_irq+0xb8/0x140
__audit_inode_child+0x240/0x7bc
tracefs_create_file+0x1b8/0x2a0
trace_create_file+0x18/0x50
event_create_dir+0x204/0x30c
__trace_add_new_event+0xac/0x100
event_trace_add_tracer+0xa0/0x130
trace_array_create_dir+0x60/0x140
trace_array_create+0x1e0/0x370
instance_mkdir+0x90/0xd0
tracefs_syscall_mkdir+0x68/0xa0
vfs_mkdir+0x21c/0x34c
do_mkdirat+0x1b4/0x1d4
__arm64_sys_mkdirat+0x4c/0x60
el0_svc_common.constprop.0+0xa8/0x240
do_el0_svc+0x8c/0xc0
el0_svc+0x20/0x30
el0_sync_handler+0xb0/0xb4
el0_sync+0x160/0x180
Therefore, we add cond_resched() to __audit_inode_child() to fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
soundwire: fix enumeration completion
The soundwire subsystem uses two completion structures that allow
drivers to wait for soundwire device to become enumerated on the bus and
initialised by their drivers, respectively.
The code implementing the signalling is currently broken as it does not
signal all current and future waiters and also uses the wrong
reinitialisation function, which can potentially lead to memory
corruption if there are still waiters on the queue.
Not signalling future waiters specifically breaks sound card probe
deferrals as codec drivers can not tell that the soundwire device is
already attached when being reprobed. Some codec runtime PM
implementations suffer from similar problems as waiting for enumeration
during resume can also timeout despite the device already having been
enumerated. |
