| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (w83791d) remove fan/pwm 4-5 sysfs group on remove
When the fan/pwm 4-5 pins are not used as GPIO, w83791d_probe()
creates the w83791d_group_fanpwm45 sysfs group on the I2C client
device.
The probe error path removes this group when a later initialization
step fails, but the normal remove path only removes w83791d_group.
As a result, the optional fan/pwm 4-5 sysfs files can remain after the
driver is unbound.
The callbacks associated with these files access the driver data,
which is devm allocated and released after driver unbind. Leaving the
sysfs files behind can therefore result in accesses to stale driver
data.
Remove w83791d_group_fanpwm45 during normal teardown as well.
This issue was found by manual code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: libipw: reject TKIP frames without a full MIC
libipw_michael_mic_verify() assumes that an skb contains an eight-byte
Michael MIC. A short TKIP frame makes the unsigned payload length wrap,
causing michael_mic() to read past the skb.
Check that the MIC is present before verifying it, and use the existing
MICHAEL_MIC_LEN constant for all MIC lengths in the verifier. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: p54: validate curve data length in the calibration curve converters
p54_convert_rev0() and p54_convert_rev1() read calibration curve
data from the device-supplied EEPROM entry using channel and
points-per-channel counts taken verbatim from that same entry, so
an entry that declares more data than it carries drives an
out-of-bounds read past the EEPROM buffer (verified with a KASAN
reproducer of the conversion loop). The sibling converters
p54_convert_output_limits() and p54_convert_db() already validate
their counts against the entry length; this path was missed.
Reject the entry when the counts do not fit in the entry data. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: p54: require a full exp_if record in PDR_INTERFACE_LIST
The PDR_INTERFACE_LIST loop only checks that the record start is within
the entry before reading an entire struct exp_if from it. A truncated
trailing record makes the if_id/variant reads cross the entry boundary
into the heap beyond the EEPROM buffer (verified with a KASAN
reproducer of the loop). The variant also feeds the synth front-end
selection, so this is not only a leak.
Advance only while a full record still fits in the entry. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: bound the pairwise-cipher OUI walk to the IE length
mwifiex_search_oui_in_ie() reads a pairwise-cipher (PTK) count from a
beacon/probe-response RSN or WPA information element and then walks that
many 4-byte OUIs, comparing each with memcmp(). The count comes straight
from the (attacker-supplied) IE and is never checked against the
element's own length, and the callers admit the element on element_id
alone (has_ieee_hdr() / has_vendor_hdr(), no length check). A crafted
RSN/WPA IE with a large pairwise count therefore makes the walk read up
to 255 * 4 bytes past the element -- an out-of-bounds read of the
kmemdup()'d beacon buffer, reachable from any AP whose beacon/probe
response is processed during scan-result parsing.
Pass the number of IE bytes available at the OUI list and bound the walk
to the element. Keep the length signed and reject a negative value
before any unsigned arithmetic, so a small or zero IE length cannot
underflow to a large size_t and defeat the bound.
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: validate scan response extents
mwifiex_ret_802_11_scan() subtracts the fixed response fields and the
firmware-provided BSS length from resp->size without first proving that
either extent fits. A short response or oversized BSS length can
therefore underflow tlv_buf_size and make the TLV parser walk beyond the
command response.
Compute the fixed extent from the selected normal or background scan
response. Validate that the fixed fields and BSS data fit before deriving
the TLV extent and entering the parser. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: avoid out-of-bounds read for empty PREQ elements
ieee80211_mesh_preq_size_ok() derives the location of the PREQ bottom
fields before checking whether the element contains even the fixed
header. ieee80211_mesh_hwmp_preq_get_bottom() reads the flags byte to
account for the optional Address Extension field. Consequently, an
empty PREQ element causes a one-byte read beyond its declared payload.
Move the helper call after both size checks, so the bottom fields are
only accessed when they are present. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: refuse to make a monitor active when it has no queue
A monitor interface only gets a TXQ if it's created active, and one can't
be added later. Setting the flag on a down interface is still allowed, so
the driver is handed a monitor with no queue. ath9k dereferences it:
BUG: kernel NULL pointer dereference, address: 0000000000000066
RIP: 0010:ath_tx_node_init+0x49/0x170 [ath9k]
ath9k_add_interface+0x10c/0x140 [ath9k]
drv_add_interface+0x54/0x250 [mac80211]
ieee80211_do_open+0x32f/0x800 [mac80211]
Reached with CAP_NET_ADMIN by "iw dev X set monitor active" followed by
"ip link set X up". RTNL is held, so netlink operations block behind it.
Refuse the flag when there is no queue to give. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gud: fix out-of-bounds write in gud_plane_atomic_check()
The plane property loop uses req->properties[num_properties + i] as write
index while simultaneously incrementing `num_properties` inside the loop.
At iteration i, num_properties has also incremented by i, so the write
is done at `initial_num_properties + 2*i`, skipping every other index and
advancing by 2 per iteration.
With just 2 connector and 32 plane properties the last write happens at
index 64, one slot past the end of the 64-slot (indices 0–63)
allocation. A USB device can trigger OOB by advertising the maximum
number of properties.
Fix by dropping the redundant `+ i`; num_properties is already the correct
running index, as gud_connector_fill_properties() fills the preceding
slots. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: RCU-free the scheduler-containing ring and VM objects
Both struct msm_ringbuffer and struct msm_gem_vm embed a struct
drm_gpu_scheduler. msm_ringbuffer_destroy() and the VM free callback
msm_gem_vm_free() call drm_sched_fini() on the embedded scheduler and then
free the containing object with plain kfree().
drm_sched_fence_get_timeline_name() returns fence->sched->name, and the
scheduler fence keeps a .release callback so it is not ops-detached on
signalling. A finished fence exported to userspace (the submit out-fence, or
a VM_BIND fence, via sync_file / drm_syncobj) keeps pointing at the embedded
scheduler after the ring/VM is freed, so a later get_timeline_name() --
reachable unprivileged through SYNC_IOC_FILE_INFO -- dereferences freed slab
memory (KASAN slab-use-after-free read).
Per the dma-fence lifetime contract the exporter must keep the data backing a
signalled fence alive for an RCU grace period. Free the scheduler-containing
objects with kfree_rcu() instead of kfree().
Patchwork: https://patchwork.freedesktop.org/patch/750234/ |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix rmmio iounmap skipped on device removal
amdgpu_pci_remove() calls drm_dev_unplug() before fini_sw(), so
drm_dev_enter() is already false there and the iounmap() guarded by it
is skipped. This .remove path runs on both hot-unplug and plain rmmod,
so the register BAR ioremap mapping leaks one instance per unload.
Unmap rmmio unconditionally (guard only on non-NULL) and drop the now
unused idx.
(cherry picked from commit dd6f86a97260e5207d3329ad03aa89fdad61b1e6) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Avoid integer underflow with ffs in EOP ring size calc
The low 6 bits of cp_hqd_eop_control store the base-2 logarithm
of the EOP ring size. This was calculated as
ffs(q->eop_ring_buffer_size / sizeof(unsigned int)) - 1 - 1
But ffs can in theory return 1 or 0, so this could underflow
(although in practice the ring buffer size cannot be less than 4096).
Change this to
ffs(q->eop_ring_buffer_size / sizeof(unsigned int) / 4)
using properties of logarithms.
(cherry picked from commit 4f18c56630383c14bfc6b2d65f88f2f895d2121a) |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: cancel reconnect work in clean_demultiplex_info()
clean_demultiplex_info() cancels server->echo delayed work but not
server->reconnect, which can cause a use-after-free when the
demultiplex thread exits while a reconnect work is still queued:
cifs_demultiplex_thread()
cifs_readv_from_socket()
cifs_reconnect()
__cifs_reconnect()
cifs_queue_server_reconn()
mod_delayed_work(cifsiod_wq, &server->reconnect, 0)
clean_demultiplex_info()
cancel_delayed_work_sync(&server->echo) // echo canceled
// reconnect NOT canceled
kfree_sensitive(server) // server freed
...later, on cifsiod_wq:
smb2_reconnect_server()
server->srv_count // UAF read of freed server
Fix this by canceling server->reconnect delayed work in
clean_demultiplex_info() before the server is freed, the same way
cifs_put_tcp_session() already does. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix rlist race and missing initialization
TCP_Server_Info.rlist is allocated via kzalloc which zeros both ->next
and ->prev to NULL instead of pointing to itself, making list_empty()
always return false and list_add() dereference a NULL ->prev pointer.
Also, cifs_signal_cifsd_for_reconnect() can be called concurrently
from multiple cifsd threads, allowing the same server's rlist node to
be added twice into the local list, corrupting it. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix use-after-free of iface in cifs_try_adding_channels()
cifs_try_adding_channels() iterates ses->iface_list with
list_for_each_entry_safe_from(), which captures the next entry
(niface) under iface_lock. The loop body then drops iface_lock for
the whole duration of cifs_ses_add_channel().
A concurrent interface refresh (SMB3_request_interfaces() ->
parse_server_interfaces()) marks all ifaces inactive and removes and
frees any that are not re-advertised via list_del() + kref_put(),
where release_iface() is a bare kfree(). Since niface typically has
no channel holding a reference, the list reference is its last and it
can be freed inside the unlocked window. On continue, the iterator
advance step then dereferences niface->iface_head.next, and the loop
body reads iface->rdma_capable/is_active, both on freed memory.
Fix this by never keeping an unreferenced list pointer across the
unlocked window. Each channel attempt now re-scans the list from the
head under iface_lock, takes a kref on the selected candidate, and
passes only that referenced candidate to cifs_ses_add_channel().
weight_fulfilled still tracks selection progress, so restarting the
scan preserves the original weighted distribution and the
weight_fulfilled-before-kref_put ordering on the failure path.
Add a per-pass attempts cap so a flapping interface refresh cannot
keep the inner loop spinning within a single tries increment. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix smbd_connection leak on cifs_get_tcp_session() error
When an RDMA connection is successfully established via
smbd_get_connection() but cifs_get_tcp_session() later fails (e.g.
kthread_create() returns an error), the error path frees tcp_ses
without first destroying the smbd_connection.
Fix this by calling smbd_destroy() in the out_err cleanup path before
kfree(tcp_ses). smbd_destroy() safely handles the case where
smbd_conn is NULL, so it can be called unconditionally. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix OOB struct field reads in move_smb2_ea_to_cifs()
In move_smb2_ea_to_cifs(), the while (src_size > 0) loop condition is
insufficient. It allows iteration to continue even if the remaining
src_size is too small to contain a complete smb2_ea_info structure.
Consequently, reads of ea_name_length and ea_value_length can occur
out-of-bounds.
Fix this by ensuring src_size >= sizeof(*src) before attempting to read
any structure fields. Additionally, reject any next_entry_offset that is
smaller than sizeof(*src) or that would advance the pointer beyond the
available buffer.
Note that for calls where the server returns a malformed EA list, the
error returned to userspace changes from -ENODATA (getxattr) or
-ERANGE (listxattr) to -EIO. This correctly signals a server protocol
error rather than misleadingly indicating "attribute not present" or
"output buffer too small". |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix reparse buffer bounds in cifs_query_reparse_point()
In cifs_query_reparse_point(), the start >= end check before casting to
struct reparse_data_buffer * only ensures the start pointer is within the
response. It fails to verify that there is enough space remaining for the
fixed 8-byte header of the structure.
If a server provides a DataOffset that leaves less than 8 bytes remaining,
the check passes, but subsequent reads of ReparseTag and ReparseDataLength
will occur out-of-bounds.
Fix this by ensuring the remaining space is at least the size of the
reparse_data_buffer structure before accessing its fields. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix server->total_read for compound encrypted PDUs
In receive_encrypted_standard(), server->total_read is left at the
full decrypted frame size when walking sub-PDUs of a compound encrypted
frame. As a result, cifs_handle_standard() passes this full size
to smb2_check_message(), causing the PDU length guards to incorrectly
validate the entire compound frame instead of the current sub-PDU.
This allows truncated non-last sub-PDUs to bypass length validation,
leading to out-of-bounds reads in smb2_get_data_area_len().
Fix this by setting server->total_read to the true length of the
current sub-PDU: next_cmd for non-last sub-PDUs, and the remaining
pdu_length for the last one. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: restrict BAR0 fallback read to SR-IOV VFs only
The BAR0 fallback read path was introduced as a workaround for SR-IOV VFs
where the VRAM aperture is not available during early init. Restrict this
workaround to only SR-IOV VFs where it's needed.
(cherry picked from commit d8a0affd207c813bd063fa2c27786f449eaf92b8) |
