| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: track a single source interface for ANYDEV timeout/throttle ops
An ANYDEV rx op (ifindex == 0) with an active RX timeout and/or
throttle timer has no defined semantics when matching frames arrive
from several interfaces: bcm_rx_handler() can run concurrently for
the same op on different CPUs, racing hrtimer_cancel()/
bcm_rx_starttimer() against bcm_rx_timeout_handler() and causing
spurious RX_TIMEOUT notifications and last_frames corruption. The
same concurrency lets throttled multiplex frames from different
interfaces clobber the single rx_ifindex/rx_stamp fields shared by
the op.
Add op->if_detected to track the first interface that delivers a
matching frame while a timeout/throttle timer is configured, and
reject frames from any other interface for that op. The claim is
decided in bcm_rx_handler() before hrtimer_cancel() touches
op->timer, so a rejected frame can never disturb the claimed
interface's watchdog. RTR-mode ops are excluded via RX_RTR_FRAME,
independent of kt_ival1/kt_ival2, since those may briefly hold a
stale value from an earlier non-RTR configuration.
The claim is released in bcm_notify() on NETDEV_UNREGISTER and in
bcm_rx_setup() when SETTIMER reconfigures the timer values.
A (re-)claim is only possible on CAN devices in NETREG_REGISTERED
dev->reg_state to cover the release in bcm_notify() where reg_state
becomes NETREG_UNREGISTERING until synchronize_net(). |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: validate frame length in bcm_rx_setup() for RTR replies
bcm_tx_setup() validates cf->len against the CAN/CAN FD DLC limits
before installing frames for TX_SETUP, but bcm_rx_setup() never did
the same for the RTR-reply frame configured via RX_SETUP with
RX_RTR_FRAME. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to a stack-based buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add missing device refcount for CAN filter removal
sashiko-bot remarked a problem with a concurrent device unregistration
in isotp.c which also is present in the bcm.c code. A former fix for raw.c
commit c275a176e4b6 ("can: raw: add missing refcount for memory leak fix")
introduced a netdevice_tracker which solves the issue for bcm.c too.
bcm_release(), bcm_delete_rx_op() and bcm_notifier() relied on
dev_get_by_index(ifindex) to re-find the device for an rx_op before
unregistering its filter. If a concurrent NETDEV_UNREGISTER has already
unlisted the device from the ifindex table, that lookup fails and
can_rx_unregister() is silently skipped, leaving a stale CAN filter
pointing at the soon-to-be-freed bcm_op/socket.
Hold a netdev_hold()/netdev_put() tracked reference on op->rx_reg_dev
from the moment the rx filter is registered in bcm_rx_setup() until it
is unregistered in bcm_rx_unreg(), and use that reference directly in
bcm_release() and bcm_delete_rx_op() instead of re-looking the device
up by ifindex. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to obtain sensitive information due to a byte-count and element-count confusion. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: free mapping node on duplicate reloc root insert
__add_reloc_root() allocates a mapping_node before inserting it into
rc->reloc_root_tree. If rb_simple_insert() finds an existing entry, it
returns the existing rb_node and leaves the newly allocated node unlinked.
The error path then returns -EEXIST without freeing the new node. Since
the node was never inserted into reloc_root_tree, the later cleanup in
put_reloc_control() cannot find it either.
Free the newly allocated node before returning -EEXIST.
The callers currently assert that -EEXIST should not happen, so this is a
defensive cleanup for an unexpected duplicate insert path. If the path is
ever reached, the local allocation should still be released. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: sata_dwc_460ex: fix infinite loop in NCQ tag completion bit-scanning
The hand-rolled bit-scanning loop in the NCQ completion path has an
infinite loop bug. When tag_mask has only high bits set (e.g.
0x80000000), the inner while loop left-shifts tag_mask until it
overflows to 0. At that point !(0 & 1) is always true and 0 <<= 1
stays 0, causing an infinite loop in hardirq context with a spinlock
held.
Replace the open-coded bit-scanning with __ffs() which correctly
finds the least significant set bit and is bounded by the width of
the argument. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an off-by-one error in bounds checking. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_ffa: Fix NULL dereference in ffa_partition_info_get()
ffa_partition_info_get() passes uuid_str directly to uuid_parse()
without a NULL check. When a caller passes NULL, uuid_parse() ->
__uuid_parse() -> uuid_is_valid() dereferences the pointer, causing
a kernel panic:
| Unable to handle kernel NULL pointer dereference at virtual address
| 0000000000000040
| pc : uuid_parse+0x40/0xac
| lr : ffa_partition_info_get+0x1c/0x94 [arm_ffa]
Add a NULL guard before uuid_parse() so a NULL argument returns
-ENODEV instead of crashing. Callers are expected to always supply
a valid partition UUID, so NULL is not a supported input. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an out-of-bounds write. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx8: drop unecessary BUG_ON()
There's no need to crash the kernel for this case.
(cherry picked from commit 4d7c25208ca612b754f3bf39e9f16e725b828891) |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/mmu: Fix use-after-free on vendor module reload
mmu_destroy_caches() destroys pte_list_desc_cache and
mmu_page_header_cache, but leaves both pointers unchanged. The pointers
live in kvm.ko, and therefore survive when a vendor module is unloaded
while kvm.ko remains loaded.
If creation of pte_list_desc_cache fails during a subsequent vendor
module load, its assignment sets pte_list_desc_cache to NULL and the
error path calls mmu_destroy_caches(). mmu_page_header_cache still
points to the cache destroyed during the preceding vendor module
unload. Passing that stale pointer to kmem_cache_destroy() causes a
slab use-after-free.
Reproduce the issue on a v7.1.3 kernel with CONFIG_KASAN=y,
CONFIG_KASAN_GENERIC=y, CONFIG_KVM=m, and CONFIG_KVM_INTEL=m. A
one-shot test hook forces pte_list_desc_cache to NULL on the second
invocation of kvm_mmu_vendor_module_init():
1. Load kvm.ko and kvm-intel.ko, creating both caches.
2. Unload only kvm_intel, leaving kvm.ko loaded.
3. Reload kvm_intel and force initialization through the -ENOMEM path.
KASAN reports:
BUG: KASAN: slab-use-after-free in
kvm_mmu_vendor_module_init+0x5b/0x170 [kvm]
...
kmem_cache_destroy+0x21/0x1d0
kvm_mmu_vendor_module_init+0x5b/0x170 [kvm]
...
Allocated by task 16817:
__kmem_cache_create_args+0x12c/0x3b0
__kmem_cache_create.constprop.0+0xb6/0xf0 [kvm]
kvm_mmu_vendor_module_init+0x13b/0x170 [kvm]
...
Freed by task 16820:
kmem_cache_destroy+0x117/0x1d0
kvm_mmu_vendor_module_exit+0x21/0x30 [kvm]
Clear both pointers immediately after destroying their caches so that
the stored state reflects the caches' lifetime and repeated cleanup is
safe.
With the fix applied, the same injected vendor module reload fails with
-ENOMEM as expected and produces no KASAN report. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix root leak if its reloc root is unexpected in merge_reloc_roots()
If we have an unexpected reloc_root for our root, we jump to the out label
but never drop the reference we obtained for root, resulting in a leak.
Add a missing btrfs_put_root() call. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ipw2100: fix potential memory leak in ipw2100_pci_init_one()
The memory allocated in the ipw2100_alloc_device() function is not freed
in some of the error paths in ipw2100_pci_init_one(). Fix that by
converting the direct return into a goto to the error path return.
The error path when pci_enable_device() fails cannot jump to fail, since
at this point priv is not set, so perform error handling inline. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211_hwsim: clamp virtio RX length before skb_put
hwsim_virtio_rx_work() passes the virtqueue used-ring length reported by
the device straight to skb_put() on a fixed-size receive skb. A backend
reporting a length larger than the skb tailroom drives skb_put() past the
buffer end and hits skb_over_panic() -- a host-triggerable guest panic
(denial of service).
Clamp the length to the skb's available room before skb_put(). A
conforming device never reports more than the posted buffer size, so valid
frames are unaffected; a truncated over-report then fails the
length/header checks in hwsim_virtio_handle_cmd() and is dropped, so
truncating rather than dropping here cannot be turned into a parsing
problem. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to obtain sensitive information due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: libertas: fix memory leak in helper_firmware_cb()
helper_firmware_cb() neglects to free the single-stage firmware image
after a successful async load, leading to a memory leak in the USB
firmware-download path.
Fix this memory leak by calling release_firmware() immediately after
lbs_fw_loaded() returns.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still present in
the current wireless tree.
An x86_64 allyesconfig build showed no new warnings. As we do not have
compatible Libertas USB hardware for exercising this firmware-download
path, no runtime testing was able to be performed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: free RNR data on MBSSID mismatch
nl80211_parse_beacon() rejects EMA RNR data when there are fewer RNR
entries than MBSSID entries.
The rejected RNR allocation has not been attached to the beacon data yet,
so free it before returning the error. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: validate PMSR FTM preamble range
PMSR FTM request parsing accepts preamble values outside the
enumerated nl80211 preamble range.
Reject out-of-range values before using them in the parser capability
bit test using the policy.
[drop unnecessary check] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: free AP_VLAN bc_buf SKBs outside IRQ lock
ieee80211_do_stop() removes AP_VLAN packets from the parent AP
ps->bc_buf while holding ps->bc_buf.lock with IRQs disabled. It then
calls ieee80211_free_txskb() before dropping the lock.
ieee80211_free_txskb() is not just a passive SKB release. For SKBs with
TX status state it can report a dropped frame through cfg80211/nl80211,
and that path can reach netlink tap transmit. This is the same reason
the pending queue cleanup in ieee80211_do_stop() already unlinks SKBs
under the queue lock and frees them after IRQ state is restored.
The buggy scenario involves two paths, with each column showing the
order within that path:
AP_VLAN management TX: AP_VLAN stop:
1. attach ACK-status state 1. clear the running state
2. queue a multicast SKB on 2. take ps->bc_buf.lock with IRQs
parent ps->bc_buf disabled
3. unlink the AP_VLAN SKB
4. call ieee80211_free_txskb()
Unlink matching AP_VLAN SKBs from ps->bc_buf under the existing lock,
but move them to a local free queue. Drop the lock and restore IRQ state
before calling ieee80211_free_txskb().
WARNING: kernel/softirq.c:430 at __local_bh_enable_ip |
