| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
blktrace: Fix uaf in blk_trace access after removing by sysfs
There is an use-after-free problem triggered by following process:
P1(sda) P2(sdb)
echo 0 > /sys/block/sdb/trace/enable
blk_trace_remove_queue
synchronize_rcu
blk_trace_free
relay_close
rcu_read_lock
__blk_add_trace
trace_note_tsk
(Iterate running_trace_list)
relay_close_buf
relay_destroy_buf
kfree(buf)
trace_note(sdb's bt)
relay_reserve
buf->offset <- nullptr deference (use-after-free) !!!
rcu_read_unlock
[ 502.714379] BUG: kernel NULL pointer dereference, address:
0000000000000010
[ 502.715260] #PF: supervisor read access in kernel mode
[ 502.715903] #PF: error_code(0x0000) - not-present page
[ 502.716546] PGD 103984067 P4D 103984067 PUD 17592b067 PMD 0
[ 502.717252] Oops: 0000 [#1] SMP
[ 502.720308] RIP: 0010:trace_note.isra.0+0x86/0x360
[ 502.732872] Call Trace:
[ 502.733193] __blk_add_trace.cold+0x137/0x1a3
[ 502.733734] blk_add_trace_rq+0x7b/0xd0
[ 502.734207] blk_add_trace_rq_issue+0x54/0xa0
[ 502.734755] blk_mq_start_request+0xde/0x1b0
[ 502.735287] scsi_queue_rq+0x528/0x1140
...
[ 502.742704] sg_new_write.isra.0+0x16e/0x3e0
[ 502.747501] sg_ioctl+0x466/0x1100
Reproduce method:
ioctl(/dev/sda, BLKTRACESETUP, blk_user_trace_setup[buf_size=127])
ioctl(/dev/sda, BLKTRACESTART)
ioctl(/dev/sdb, BLKTRACESETUP, blk_user_trace_setup[buf_size=127])
ioctl(/dev/sdb, BLKTRACESTART)
echo 0 > /sys/block/sdb/trace/enable &
// Add delay(mdelay/msleep) before kernel enters blk_trace_free()
ioctl$SG_IO(/dev/sda, SG_IO, ...)
// Enters trace_note_tsk() after blk_trace_free() returned
// Use mdelay in rcu region rather than msleep(which may schedule out)
Remove blk_trace from running_list before calling blk_trace_free() by
sysfs if blk_trace is at Blktrace_running state. |
| In the Linux kernel, the following vulnerability has been resolved:
mcb: fix error handling in mcb_alloc_bus()
There are two bugs:
1) If ida_simple_get() fails then this code calls put_device(carrier)
but we haven't yet called get_device(carrier) and probably that
leads to a use after free.
2) After device_initialize() then we need to use put_device() to
release the bus. This will free the internal resources tied to the
device and call mcb_free_bus() which will free the rest. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: greybus: uart: fix tty use after free
User space can hold a tty open indefinitely and tty drivers must not
release the underlying structures until the last user is gone.
Switch to using the tty-port reference counter to manage the life time
of the greybus tty state to avoid use after free after a disconnect. |
| In the Linux kernel, the following vulnerability has been resolved:
fbmem: Do not delete the mode that is still in use
The execution of fb_delete_videomode() is not based on the result of the
previous fbcon_mode_deleted(). As a result, the mode is directly deleted,
regardless of whether it is still in use, which may cause UAF.
==================================================================
BUG: KASAN: use-after-free in fb_mode_is_equal+0x36e/0x5e0 \
drivers/video/fbdev/core/modedb.c:924
Read of size 4 at addr ffff88807e0ddb1c by task syz-executor.0/18962
CPU: 2 PID: 18962 Comm: syz-executor.0 Not tainted 5.10.45-rc1+ #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ...
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x137/0x1be lib/dump_stack.c:118
print_address_description+0x6c/0x640 mm/kasan/report.c:385
__kasan_report mm/kasan/report.c:545 [inline]
kasan_report+0x13d/0x1e0 mm/kasan/report.c:562
fb_mode_is_equal+0x36e/0x5e0 drivers/video/fbdev/core/modedb.c:924
fbcon_mode_deleted+0x16a/0x220 drivers/video/fbdev/core/fbcon.c:2746
fb_set_var+0x1e1/0xdb0 drivers/video/fbdev/core/fbmem.c:975
do_fb_ioctl+0x4d9/0x6e0 drivers/video/fbdev/core/fbmem.c:1108
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl+0xfb/0x170 fs/ioctl.c:739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 18960:
kasan_save_stack mm/kasan/common.c:48 [inline]
kasan_set_track+0x3d/0x70 mm/kasan/common.c:56
kasan_set_free_info+0x17/0x30 mm/kasan/generic.c:355
__kasan_slab_free+0x108/0x140 mm/kasan/common.c:422
slab_free_hook mm/slub.c:1541 [inline]
slab_free_freelist_hook+0xd6/0x1a0 mm/slub.c:1574
slab_free mm/slub.c:3139 [inline]
kfree+0xca/0x3d0 mm/slub.c:4121
fb_delete_videomode+0x56a/0x820 drivers/video/fbdev/core/modedb.c:1104
fb_set_var+0x1f3/0xdb0 drivers/video/fbdev/core/fbmem.c:978
do_fb_ioctl+0x4d9/0x6e0 drivers/video/fbdev/core/fbmem.c:1108
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl+0xfb/0x170 fs/ioctl.c:739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9 |
| In the Linux kernel, the following vulnerability has been resolved:
arch_topology: Avoid use-after-free for scale_freq_data
Currently topology_scale_freq_tick() (which gets called from
scheduler_tick()) may end up using a pointer to "struct
scale_freq_data", which was previously cleared by
topology_clear_scale_freq_source(), as there is no protection in place
here. The users of topology_clear_scale_freq_source() though needs a
guarantee that the previously cleared scale_freq_data isn't used
anymore, so they can free the related resources.
Since topology_scale_freq_tick() is called from scheduler tick, we don't
want to add locking in there. Use the RCU update mechanism instead
(which is already used by the scheduler's utilization update path) to
guarantee race free updates here.
synchronize_rcu() makes sure that all RCU critical sections that started
before it is called, will finish before it returns. And so the callers
of topology_clear_scale_freq_source() don't need to worry about their
callback getting called anymore. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qcom/emac: fix UAF in emac_remove
adpt is netdev private data and it cannot be
used after free_netdev() call. Using adpt after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ti: fix UAF in tlan_remove_one
priv is netdev private data and it cannot be
used after free_netdev() call. Using priv after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function. |
| In the Linux kernel, the following vulnerability has been resolved:
net: fddi: fix UAF in fza_probe
fp is netdev private data and it cannot be
used after free_netdev() call. Using fp after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() after error message.
TURBOchannel adapter") |
| In the Linux kernel, the following vulnerability has been resolved:
igc: Fix use-after-free error during reset
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igc_poll() runs
while the controller is being reset this can lead to the driver try to
free a skb that was already freed.
Log message:
[ 101.525242] refcount_t: underflow; use-after-free.
[ 101.525251] WARNING: CPU: 1 PID: 646 at lib/refcount.c:28 refcount_warn_saturate+0xab/0xf0
[ 101.525259] Modules linked in: sch_etf(E) sch_mqprio(E) rfkill(E) intel_rapl_msr(E) intel_rapl_common(E)
x86_pkg_temp_thermal(E) intel_powerclamp(E) coretemp(E) binfmt_misc(E) kvm_intel(E) kvm(E) irqbypass(E) crc32_pclmul(E)
ghash_clmulni_intel(E) aesni_intel(E) mei_wdt(E) libaes(E) crypto_simd(E) cryptd(E) glue_helper(E) snd_hda_codec_hdmi(E)
rapl(E) intel_cstate(E) snd_hda_intel(E) snd_intel_dspcfg(E) sg(E) soundwire_intel(E) intel_uncore(E) at24(E)
soundwire_generic_allocation(E) iTCO_wdt(E) soundwire_cadence(E) intel_pmc_bxt(E) serio_raw(E) snd_hda_codec(E)
iTCO_vendor_support(E) watchdog(E) snd_hda_core(E) snd_hwdep(E) snd_soc_core(E) snd_compress(E) snd_pcsp(E)
soundwire_bus(E) snd_pcm(E) evdev(E) snd_timer(E) mei_me(E) snd(E) soundcore(E) mei(E) configfs(E) ip_tables(E) x_tables(E)
autofs4(E) ext4(E) crc32c_generic(E) crc16(E) mbcache(E) jbd2(E) sd_mod(E) t10_pi(E) crc_t10dif(E) crct10dif_generic(E)
i915(E) ahci(E) libahci(E) ehci_pci(E) igb(E) xhci_pci(E) ehci_hcd(E)
[ 101.525303] drm_kms_helper(E) dca(E) xhci_hcd(E) libata(E) crct10dif_pclmul(E) cec(E) crct10dif_common(E) tsn(E) igc(E)
e1000e(E) ptp(E) i2c_i801(E) crc32c_intel(E) psmouse(E) i2c_algo_bit(E) i2c_smbus(E) scsi_mod(E) lpc_ich(E) pps_core(E)
usbcore(E) drm(E) button(E) video(E)
[ 101.525318] CPU: 1 PID: 646 Comm: irq/37-enp7s0-T Tainted: G E 5.10.30-rt37-tsn1-rt-ipipe #ipipe
[ 101.525320] Hardware name: SIEMENS AG SIMATIC IPC427D/A5E31233588, BIOS V17.02.09 03/31/2017
[ 101.525322] RIP: 0010:refcount_warn_saturate+0xab/0xf0
[ 101.525325] Code: 05 31 48 44 01 01 e8 f0 c6 42 00 0f 0b c3 80 3d 1f 48 44 01 00 75 90 48 c7 c7 78 a8 f3 a6 c6 05 0f 48
44 01 01 e8 d1 c6 42 00 <0f> 0b c3 80 3d fe 47 44 01 00 0f 85 6d ff ff ff 48 c7 c7 d0 a8 f3
[ 101.525327] RSP: 0018:ffffbdedc0917cb8 EFLAGS: 00010286
[ 101.525329] RAX: 0000000000000000 RBX: ffff98fd6becbf40 RCX: 0000000000000001
[ 101.525330] RDX: 0000000000000001 RSI: ffffffffa6f2700c RDI: 00000000ffffffff
[ 101.525332] RBP: ffff98fd6becc14c R08: ffffffffa7463d00 R09: ffffbdedc0917c50
[ 101.525333] R10: ffffffffa74c3578 R11: 0000000000000034 R12: 00000000ffffff00
[ 101.525335] R13: ffff98fd6b0b1000 R14: 0000000000000039 R15: ffff98fd6be35c40
[ 101.525337] FS: 0000000000000000(0000) GS:ffff98fd6e240000(0000) knlGS:0000000000000000
[ 101.525339] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 101.525341] CR2: 00007f34135a3a70 CR3: 0000000150210003 CR4: 00000000001706e0
[ 101.525343] Call Trace:
[ 101.525346] sock_wfree+0x9c/0xa0
[ 101.525353] unix_destruct_scm+0x7b/0xa0
[ 101.525358] skb_release_head_state+0x40/0x90
[ 101.525362] skb_release_all+0xe/0x30
[ 101.525364] napi_consume_skb+0x57/0x160
[ 101.525367] igc_poll+0xb7/0xc80 [igc]
[ 101.525376] ? sched_clock+0x5/0x10
[ 101.525381] ? sched_clock_cpu+0xe/0x100
[ 101.525385] net_rx_action+0x14c/0x410
[ 101.525388] __do_softirq+0xe9/0x2f4
[ 101.525391] __local_bh_enable_ip+0xe3/0x110
[ 101.525395] ? irq_finalize_oneshot.part.47+0xe0/0xe0
[ 101.525398] irq_forced_thread_fn+0x6a/0x80
[ 101.525401] irq_thread+0xe8/0x180
[ 101.525403] ? wake_threads_waitq+0x30/0x30
[ 101.525406] ? irq_thread_check_affinity+0xd0/0xd0
[ 101.525408] kthread+0x183/0x1a0
[ 101.525412] ? kthread_park+0x80/0x80
[ 101.525415] ret_from_fork+0x22/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
igb: Fix use-after-free error during reset
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.
(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc) |
| In the Linux kernel, the following vulnerability has been resolved:
xdp, net: Fix use-after-free in bpf_xdp_link_release
The problem occurs between dev_get_by_index() and dev_xdp_attach_link().
At this point, dev_xdp_uninstall() is called. Then xdp link will not be
detached automatically when dev is released. But link->dev already
points to dev, when xdp link is released, dev will still be accessed,
but dev has been released.
dev_get_by_index() |
link->dev = dev |
| rtnl_lock()
| unregister_netdevice_many()
| dev_xdp_uninstall()
| rtnl_unlock()
rtnl_lock(); |
dev_xdp_attach_link() |
rtnl_unlock(); |
| netdev_run_todo() // dev released
bpf_xdp_link_release() |
/* access dev. |
use-after-free */ |
[ 45.966867] BUG: KASAN: use-after-free in bpf_xdp_link_release+0x3b8/0x3d0
[ 45.967619] Read of size 8 at addr ffff00000f9980c8 by task a.out/732
[ 45.968297]
[ 45.968502] CPU: 1 PID: 732 Comm: a.out Not tainted 5.13.0+ #22
[ 45.969222] Hardware name: linux,dummy-virt (DT)
[ 45.969795] Call trace:
[ 45.970106] dump_backtrace+0x0/0x4c8
[ 45.970564] show_stack+0x30/0x40
[ 45.970981] dump_stack_lvl+0x120/0x18c
[ 45.971470] print_address_description.constprop.0+0x74/0x30c
[ 45.972182] kasan_report+0x1e8/0x200
[ 45.972659] __asan_report_load8_noabort+0x2c/0x50
[ 45.973273] bpf_xdp_link_release+0x3b8/0x3d0
[ 45.973834] bpf_link_free+0xd0/0x188
[ 45.974315] bpf_link_put+0x1d0/0x218
[ 45.974790] bpf_link_release+0x3c/0x58
[ 45.975291] __fput+0x20c/0x7e8
[ 45.975706] ____fput+0x24/0x30
[ 45.976117] task_work_run+0x104/0x258
[ 45.976609] do_notify_resume+0x894/0xaf8
[ 45.977121] work_pending+0xc/0x328
[ 45.977575]
[ 45.977775] The buggy address belongs to the page:
[ 45.978369] page:fffffc00003e6600 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x4f998
[ 45.979522] flags: 0x7fffe0000000000(node=0|zone=0|lastcpupid=0x3ffff)
[ 45.980349] raw: 07fffe0000000000 fffffc00003e6708 ffff0000dac3c010 0000000000000000
[ 45.981309] raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
[ 45.982259] page dumped because: kasan: bad access detected
[ 45.982948]
[ 45.983153] Memory state around the buggy address:
[ 45.983753] ffff00000f997f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 45.984645] ffff00000f998000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 45.985533] >ffff00000f998080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 45.986419] ^
[ 45.987112] ffff00000f998100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 45.988006] ffff00000f998180: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 45.988895] ==================================================================
[ 45.989773] Disabling lock debugging due to kernel taint
[ 45.990552] Kernel panic - not syncing: panic_on_warn set ...
[ 45.991166] CPU: 1 PID: 732 Comm: a.out Tainted: G B 5.13.0+ #22
[ 45.991929] Hardware name: linux,dummy-virt (DT)
[ 45.992448] Call trace:
[ 45.992753] dump_backtrace+0x0/0x4c8
[ 45.993208] show_stack+0x30/0x40
[ 45.993627] dump_stack_lvl+0x120/0x18c
[ 45.994113] dump_stack+0x1c/0x34
[ 45.994530] panic+0x3a4/0x7d8
[ 45.994930] end_report+0x194/0x198
[ 45.995380] kasan_report+0x134/0x200
[ 45.995850] __asan_report_load8_noabort+0x2c/0x50
[ 45.996453] bpf_xdp_link_release+0x3b8/0x3d0
[ 45.997007] bpf_link_free+0xd0/0x188
[ 45.997474] bpf_link_put+0x1d0/0x218
[ 45.997942] bpf_link_release+0x3c/0x58
[ 45.998429] __fput+0x20c/0x7e8
[ 45.998833] ____fput+0x24/0x30
[ 45.999247] task_work_run+0x104/0x258
[ 45.999731] do_notify_resume+0x894/0xaf8
[ 46.000236] work_pending
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
bus: mhi: pci_generic: Fix possible use-after-free in mhi_pci_remove()
This driver's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: fix possible use-after-free in smsc75xx_bind
The commit 46a8b29c6306 ("net: usb: fix memory leak in smsc75xx_bind")
fails to clean up the work scheduled in smsc75xx_reset->
smsc75xx_set_multicast, which leads to use-after-free if the work is
scheduled to start after the deallocation. In addition, this patch
also removes a dangling pointer - dev->data[0].
This patch calls cancel_work_sync to cancel the scheduled work and set
the dangling pointer to NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: fix potential use-after-free in ec_bhf_remove
static void ec_bhf_remove(struct pci_dev *dev)
{
...
struct ec_bhf_priv *priv = netdev_priv(net_dev);
unregister_netdev(net_dev);
free_netdev(net_dev);
pci_iounmap(dev, priv->dma_io);
pci_iounmap(dev, priv->io);
...
}
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after pci_iounmap()
calls. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: fix vlan tunnel dst refcnt when egressing
The egress tunnel code uses dst_clone() and directly sets the result
which is wrong because the entry might have 0 refcnt or be already deleted,
causing number of problems. It also triggers the WARN_ON() in dst_hold()[1]
when a refcnt couldn't be taken. Fix it by using dst_hold_safe() and
checking if a reference was actually taken before setting the dst.
[1] dmesg WARN_ON log and following refcnt errors
WARNING: CPU: 5 PID: 38 at include/net/dst.h:230 br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge]
Modules linked in: 8021q garp mrp bridge stp llc bonding ipv6 virtio_net
CPU: 5 PID: 38 Comm: ksoftirqd/5 Kdump: loaded Tainted: G W 5.13.0-rc3+ #360
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
RIP: 0010:br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge]
Code: e8 85 bc 01 e1 45 84 f6 74 90 45 31 f6 85 db 48 c7 c7 a0 02 19 a0 41 0f 94 c6 31 c9 31 d2 44 89 f6 e8 64 bc 01 e1 85 db 75 02 <0f> 0b 31 c9 31 d2 44 89 f6 48 c7 c7 70 02 19 a0 e8 4b bc 01 e1 49
RSP: 0018:ffff8881003d39e8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffffa01902a0
RBP: ffff8881040c6700 R08: 0000000000000000 R09: 0000000000000001
R10: 2ce93d0054fe0d00 R11: 54fe0d00000e0000 R12: ffff888109515000
R13: 0000000000000000 R14: 0000000000000001 R15: 0000000000000401
FS: 0000000000000000(0000) GS:ffff88822bf40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f42ba70f030 CR3: 0000000109926000 CR4: 00000000000006e0
Call Trace:
br_handle_vlan+0xbc/0xca [bridge]
__br_forward+0x23/0x164 [bridge]
deliver_clone+0x41/0x48 [bridge]
br_handle_frame_finish+0x36f/0x3aa [bridge]
? skb_dst+0x2e/0x38 [bridge]
? br_handle_ingress_vlan_tunnel+0x3e/0x1c8 [bridge]
? br_handle_frame_finish+0x3aa/0x3aa [bridge]
br_handle_frame+0x2c3/0x377 [bridge]
? __skb_pull+0x33/0x51
? vlan_do_receive+0x4f/0x36a
? br_handle_frame_finish+0x3aa/0x3aa [bridge]
__netif_receive_skb_core+0x539/0x7c6
? __list_del_entry_valid+0x16e/0x1c2
__netif_receive_skb_list_core+0x6d/0xd6
netif_receive_skb_list_internal+0x1d9/0x1fa
gro_normal_list+0x22/0x3e
dev_gro_receive+0x55b/0x600
? detach_buf_split+0x58/0x140
napi_gro_receive+0x94/0x12e
virtnet_poll+0x15d/0x315 [virtio_net]
__napi_poll+0x2c/0x1c9
net_rx_action+0xe6/0x1fb
__do_softirq+0x115/0x2d8
run_ksoftirqd+0x18/0x20
smpboot_thread_fn+0x183/0x19c
? smpboot_unregister_percpu_thread+0x66/0x66
kthread+0x10a/0x10f
? kthread_mod_delayed_work+0xb6/0xb6
ret_from_fork+0x22/0x30
---[ end trace 49f61b07f775fd2b ]---
dst_release: dst:00000000c02d677a refcnt:-1
dst_release underflow |
| In the Linux kernel, the following vulnerability has been resolved:
net: dpaa2-eth: fix use-after-free in dpaa2_eth_remove
Access to netdev after free_netdev() will cause use-after-free bug.
Move debug log before free_netdev() call to avoid it. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/prime: Fix use after free in mmap with drm_gem_ttm_mmap
drm_gem_ttm_mmap() drops a reference to the gem object on success. If
the gem object's refcount == 1 on entry to drm_gem_prime_mmap(), that
drop will free the gem object, and the subsequent drm_gem_object_get()
will be a UAF. Fix by grabbing a reference before calling the mmap
helper.
This issue was forseen when the reference dropping was adding in
commit 9786b65bc61ac ("drm/ttm: fix mmap refcounting"):
"For that to work properly the drm_gem_object_get() call in
drm_gem_ttm_mmap() must be moved so it happens before calling
obj->funcs->mmap(), otherwise the gem refcount would go down
to zero." |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: fix ltout double free on completion race
Always remove linked timeout on io_link_timeout_fn() from the master
request link list, otherwise we may get use-after-free when first
io_link_timeout_fn() puts linked timeout in the fail path, and then
will be found and put on master's free. |
| In the Linux kernel, the following vulnerability has been resolved:
pid: take a reference when initializing `cad_pid`
During boot, kernel_init_freeable() initializes `cad_pid` to the init
task's struct pid. Later on, we may change `cad_pid` via a sysctl, and
when this happens proc_do_cad_pid() will increment the refcount on the
new pid via get_pid(), and will decrement the refcount on the old pid
via put_pid(). As we never called get_pid() when we initialized
`cad_pid`, we decrement a reference we never incremented, can therefore
free the init task's struct pid early. As there can be dangling
references to the struct pid, we can later encounter a use-after-free
(e.g. when delivering signals).
This was spotted when fuzzing v5.13-rc3 with Syzkaller, but seems to
have been around since the conversion of `cad_pid` to struct pid in
commit 9ec52099e4b8 ("[PATCH] replace cad_pid by a struct pid") from the
pre-KASAN stone age of v2.6.19.
Fix this by getting a reference to the init task's struct pid when we
assign it to `cad_pid`.
Full KASAN splat below.
==================================================================
BUG: KASAN: use-after-free in ns_of_pid include/linux/pid.h:153 [inline]
BUG: KASAN: use-after-free in task_active_pid_ns+0xc0/0xc8 kernel/pid.c:509
Read of size 4 at addr ffff23794dda0004 by task syz-executor.0/273
CPU: 1 PID: 273 Comm: syz-executor.0 Not tainted 5.12.0-00001-g9aef892b2d15 #1
Hardware name: linux,dummy-virt (DT)
Call trace:
ns_of_pid include/linux/pid.h:153 [inline]
task_active_pid_ns+0xc0/0xc8 kernel/pid.c:509
do_notify_parent+0x308/0xe60 kernel/signal.c:1950
exit_notify kernel/exit.c:682 [inline]
do_exit+0x2334/0x2bd0 kernel/exit.c:845
do_group_exit+0x108/0x2c8 kernel/exit.c:922
get_signal+0x4e4/0x2a88 kernel/signal.c:2781
do_signal arch/arm64/kernel/signal.c:882 [inline]
do_notify_resume+0x300/0x970 arch/arm64/kernel/signal.c:936
work_pending+0xc/0x2dc
Allocated by task 0:
slab_post_alloc_hook+0x50/0x5c0 mm/slab.h:516
slab_alloc_node mm/slub.c:2907 [inline]
slab_alloc mm/slub.c:2915 [inline]
kmem_cache_alloc+0x1f4/0x4c0 mm/slub.c:2920
alloc_pid+0xdc/0xc00 kernel/pid.c:180
copy_process+0x2794/0x5e18 kernel/fork.c:2129
kernel_clone+0x194/0x13c8 kernel/fork.c:2500
kernel_thread+0xd4/0x110 kernel/fork.c:2552
rest_init+0x44/0x4a0 init/main.c:687
arch_call_rest_init+0x1c/0x28
start_kernel+0x520/0x554 init/main.c:1064
0x0
Freed by task 270:
slab_free_hook mm/slub.c:1562 [inline]
slab_free_freelist_hook+0x98/0x260 mm/slub.c:1600
slab_free mm/slub.c:3161 [inline]
kmem_cache_free+0x224/0x8e0 mm/slub.c:3177
put_pid.part.4+0xe0/0x1a8 kernel/pid.c:114
put_pid+0x30/0x48 kernel/pid.c:109
proc_do_cad_pid+0x190/0x1b0 kernel/sysctl.c:1401
proc_sys_call_handler+0x338/0x4b0 fs/proc/proc_sysctl.c:591
proc_sys_write+0x34/0x48 fs/proc/proc_sysctl.c:617
call_write_iter include/linux/fs.h:1977 [inline]
new_sync_write+0x3ac/0x510 fs/read_write.c:518
vfs_write fs/read_write.c:605 [inline]
vfs_write+0x9c4/0x1018 fs/read_write.c:585
ksys_write+0x124/0x240 fs/read_write.c:658
__do_sys_write fs/read_write.c:670 [inline]
__se_sys_write fs/read_write.c:667 [inline]
__arm64_sys_write+0x78/0xb0 fs/read_write.c:667
__invoke_syscall arch/arm64/kernel/syscall.c:37 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:49 [inline]
el0_svc_common.constprop.1+0x16c/0x388 arch/arm64/kernel/syscall.c:129
do_el0_svc+0xf8/0x150 arch/arm64/kernel/syscall.c:168
el0_svc+0x28/0x38 arch/arm64/kernel/entry-common.c:416
el0_sync_handler+0x134/0x180 arch/arm64/kernel/entry-common.c:432
el0_sync+0x154/0x180 arch/arm64/kernel/entry.S:701
The buggy address belongs to the object at ffff23794dda0000
which belongs to the cache pid of size 224
The buggy address is located 4 bytes inside of
224-byte region [ff
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: fix use-after-free in nft_set_catchall_destroy()
We need to use list_for_each_entry_safe() iterator
because we can not access @catchall after kfree_rcu() call.
syzbot reported:
BUG: KASAN: use-after-free in nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline]
BUG: KASAN: use-after-free in nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline]
BUG: KASAN: use-after-free in nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493
Read of size 8 at addr ffff8880716e5b80 by task syz-executor.3/8871
CPU: 1 PID: 8871 Comm: syz-executor.3 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x2ed mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:450
nft_set_catchall_destroy net/netfilter/nf_tables_api.c:4486 [inline]
nft_set_destroy net/netfilter/nf_tables_api.c:4504 [inline]
nft_set_destroy+0x3fd/0x4f0 net/netfilter/nf_tables_api.c:4493
__nft_release_table+0x79f/0xcd0 net/netfilter/nf_tables_api.c:9626
nft_rcv_nl_event+0x4f8/0x670 net/netfilter/nf_tables_api.c:9688
notifier_call_chain+0xb5/0x200 kernel/notifier.c:83
blocking_notifier_call_chain kernel/notifier.c:318 [inline]
blocking_notifier_call_chain+0x67/0x90 kernel/notifier.c:306
netlink_release+0xcb6/0x1dd0 net/netlink/af_netlink.c:788
__sock_release+0xcd/0x280 net/socket.c:649
sock_close+0x18/0x20 net/socket.c:1314
__fput+0x286/0x9f0 fs/file_table.c:280
task_work_run+0xdd/0x1a0 kernel/task_work.c:164
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
exit_to_user_mode_prepare+0x27e/0x290 kernel/entry/common.c:207
__syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300
do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f75fbf28adb
Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24 0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44
RSP: 002b:00007ffd8da7ec10 EFLAGS: 00000293 ORIG_RAX: 0000000000000003
RAX: 0000000000000000 RBX: 0000000000000004 RCX: 00007f75fbf28adb
RDX: 00007f75fc08e828 RSI: ffffffffffffffff RDI: 0000000000000003
RBP: 00007f75fc08a960 R08: 0000000000000000 R09: 00007f75fc08e830
R10: 00007ffd8da7ed10 R11: 0000000000000293 R12: 00000000002067c3
R13: 00007ffd8da7ed10 R14: 00007f75fc088f60 R15: 0000000000000032
</TASK>
Allocated by task 8886:
kasan_save_stack+0x1e/0x50 mm/kasan/common.c:38
kasan_set_track mm/kasan/common.c:46 [inline]
set_alloc_info mm/kasan/common.c:434 [inline]
____kasan_kmalloc mm/kasan/common.c:513 [inline]
____kasan_kmalloc mm/kasan/common.c:472 [inline]
__kasan_kmalloc+0xa6/0xd0 mm/kasan/common.c:522
kasan_kmalloc include/linux/kasan.h:269 [inline]
kmem_cache_alloc_trace+0x1ea/0x4a0 mm/slab.c:3575
kmalloc include/linux/slab.h:590 [inline]
nft_setelem_catchall_insert net/netfilter/nf_tables_api.c:5544 [inline]
nft_setelem_insert net/netfilter/nf_tables_api.c:5562 [inline]
nft_add_set_elem+0x232e/0x2f40 net/netfilter/nf_tables_api.c:5936
nf_tables_newsetelem+0x6ff/0xbb0 net/netfilter/nf_tables_api.c:6032
nfnetlink_rcv_batch+0x1710/0x25f0 net/netfilter/nfnetlink.c:513
nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
nfnetlink_rcv+0x3af/0x420 net/netfilter/nfnetlink.c:652
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x533/0x7d0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x904/0xdf0 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/
---truncated--- |
