| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mm/kmemleak: avoid deadlock by moving pr_warn() outside kmemleak_lock
When netpoll is enabled, calling pr_warn_once() while holding
kmemleak_lock in mem_pool_alloc() can cause a deadlock due to lock
inversion with the netconsole subsystem. This occurs because
pr_warn_once() may trigger netpoll, which eventually leads to
__alloc_skb() and back into kmemleak code, attempting to reacquire
kmemleak_lock.
This is the path for the deadlock.
mem_pool_alloc()
-> raw_spin_lock_irqsave(&kmemleak_lock, flags);
-> pr_warn_once()
-> netconsole subsystem
-> netpoll
-> __alloc_skb
-> __create_object
-> raw_spin_lock_irqsave(&kmemleak_lock, flags);
Fix this by setting a flag and issuing the pr_warn_once() after
kmemleak_lock is released. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/kmemleak: avoid soft lockup in __kmemleak_do_cleanup()
A soft lockup warning was observed on a relative small system x86-64
system with 16 GB of memory when running a debug kernel with kmemleak
enabled.
watchdog: BUG: soft lockup - CPU#8 stuck for 33s! [kworker/8:1:134]
The test system was running a workload with hot unplug happening in
parallel. Then kemleak decided to disable itself due to its inability to
allocate more kmemleak objects. The debug kernel has its
CONFIG_DEBUG_KMEMLEAK_MEM_POOL_SIZE set to 40,000.
The soft lockup happened in kmemleak_do_cleanup() when the existing
kmemleak objects were being removed and deleted one-by-one in a loop via a
workqueue. In this particular case, there are at least 40,000 objects
that need to be processed and given the slowness of a debug kernel and the
fact that a raw_spinlock has to be acquired and released in
__delete_object(), it could take a while to properly handle all these
objects.
As kmemleak has been disabled in this case, the object removal and
deletion process can be further optimized as locking isn't really needed.
However, it is probably not worth the effort to optimize for such an edge
case that should rarely happen. So the simple solution is to call
cond_resched() at periodic interval in the iteration loop to avoid soft
lockup. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/migrate: don't overflow max copy size
With non-page aligned copy, we need to use 4 byte aligned pitch, however
the size itself might still be close to our maximum of ~8M, and so the
dimensions of the copy can easily exceed the S16_MAX limit of the copy
command leading to the following assert:
xe 0000:03:00.0: [drm] Assertion `size / pitch <= ((s16)(((u16)~0U) >> 1))` failed!
platform: BATTLEMAGE subplatform: 1
graphics: Xe2_HPG 20.01 step A0
media: Xe2_HPM 13.01 step A1
tile: 0 VRAM 10.0 GiB
GT: 0 type 1
WARNING: CPU: 23 PID: 10605 at drivers/gpu/drm/xe/xe_migrate.c:673 emit_copy+0x4b5/0x4e0 [xe]
To fix this account for the pitch when calculating the number of current
bytes to copy.
(cherry picked from commit 8c2d61e0e916e077fda7e7b8e67f25ffe0f361fc) |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA: hfi1: fix possible divide-by-zero in find_hw_thread_mask()
The function divides number of online CPUs by num_core_siblings, and
later checks the divider by zero. This implies a possibility to get
and divide-by-zero runtime error. Fix it by moving the check prior to
division. This also helps to save one indentation level. |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: truncate good inode pages when hard link is 0
The fileset value of the inode copy from the disk by the reproducer is
AGGR_RESERVED_I. When executing evict, its hard link number is 0, so its
inode pages are not truncated. This causes the bugon to be triggered when
executing clear_inode() because nrpages is greater than 0. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: Fix rcu_read_unlock() deadloop due to IRQ work
During rcu_read_unlock_special(), if this happens during irq_exit(), we
can lockup if an IPI is issued. This is because the IPI itself triggers
the irq_exit() path causing a recursive lock up.
This is precisely what Xiongfeng found when invoking a BPF program on
the trace_tick_stop() tracepoint As shown in the trace below. Fix by
managing the irq_work state correctly.
irq_exit()
__irq_exit_rcu()
/* in_hardirq() returns false after this */
preempt_count_sub(HARDIRQ_OFFSET)
tick_irq_exit()
tick_nohz_irq_exit()
tick_nohz_stop_sched_tick()
trace_tick_stop() /* a bpf prog is hooked on this trace point */
__bpf_trace_tick_stop()
bpf_trace_run2()
rcu_read_unlock_special()
/* will send a IPI to itself */
irq_work_queue_on(&rdp->defer_qs_iw, rdp->cpu);
A simple reproducer can also be obtained by doing the following in
tick_irq_exit(). It will hang on boot without the patch:
static inline void tick_irq_exit(void)
{
+ rcu_read_lock();
+ WRITE_ONCE(current->rcu_read_unlock_special.b.need_qs, true);
+ rcu_read_unlock();
+
[neeraj: Apply Frederic's suggested fix for PREEMPT_RT] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath10k: shutdown driver when hardware is unreliable
In rare cases, ath10k may lose connection with the PCIe bus due to
some unknown reasons, which could further lead to system crashes during
resuming due to watchdog timeout:
ath10k_pci 0000:01:00.0: wmi command 20486 timeout, restarting hardware
ath10k_pci 0000:01:00.0: already restarting
ath10k_pci 0000:01:00.0: failed to stop WMI vdev 0: -11
ath10k_pci 0000:01:00.0: failed to stop vdev 0: -11
ieee80211 phy0: PM: **** DPM device timeout ****
Call Trace:
panic+0x125/0x315
dpm_watchdog_set+0x54/0x54
dpm_watchdog_handler+0x57/0x57
call_timer_fn+0x31/0x13c
At this point, all WMI commands will timeout and attempt to restart
device. So set a threshold for consecutive restart failures. If the
threshold is exceeded, consider the hardware is unreliable and all
ath10k operations should be skipped to avoid system crash.
fail_cont_count and pending_recovery are atomic variables, and
do not involve complex conditional logic. Therefore, even if recovery
check and reconfig complete are executed concurrently, the recovery
mechanism will not be broken.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Forget ranges when refining tnum after JSET
Syzbot reported a kernel warning due to a range invariant violation on
the following BPF program.
0: call bpf_get_netns_cookie
1: if r0 == 0 goto <exit>
2: if r0 & Oxffffffff goto <exit>
The issue is on the path where we fall through both jumps.
That path is unreachable at runtime: after insn 1, we know r0 != 0, but
with the sign extension on the jset, we would only fallthrough insn 2
if r0 == 0. Unfortunately, is_branch_taken() isn't currently able to
figure this out, so the verifier walks all branches. The verifier then
refines the register bounds using the second condition and we end
up with inconsistent bounds on this unreachable path:
1: if r0 == 0 goto <exit>
r0: u64=[0x1, 0xffffffffffffffff] var_off=(0, 0xffffffffffffffff)
2: if r0 & 0xffffffff goto <exit>
r0 before reg_bounds_sync: u64=[0x1, 0xffffffffffffffff] var_off=(0, 0)
r0 after reg_bounds_sync: u64=[0x1, 0] var_off=(0, 0)
Improving the range refinement for JSET to cover all cases is tricky. We
also don't expect many users to rely on JSET given LLVM doesn't generate
those instructions. So instead of improving the range refinement for
JSETs, Eduard suggested we forget the ranges whenever we're narrowing
tnums after a JSET. This patch implements that approach. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: Protect ->defer_qs_iw_pending from data race
On kernels built with CONFIG_IRQ_WORK=y, when rcu_read_unlock() is
invoked within an interrupts-disabled region of code [1], it will invoke
rcu_read_unlock_special(), which uses an irq-work handler to force the
system to notice when the RCU read-side critical section actually ends.
That end won't happen until interrupts are enabled at the soonest.
In some kernels, such as those booted with rcutree.use_softirq=y, the
irq-work handler is used unconditionally.
The per-CPU rcu_data structure's ->defer_qs_iw_pending field is
updated by the irq-work handler and is both read and updated by
rcu_read_unlock_special(). This resulted in the following KCSAN splat:
------------------------------------------------------------------------
BUG: KCSAN: data-race in rcu_preempt_deferred_qs_handler / rcu_read_unlock_special
read to 0xffff96b95f42d8d8 of 1 bytes by task 90 on cpu 8:
rcu_read_unlock_special+0x175/0x260
__rcu_read_unlock+0x92/0xa0
rt_spin_unlock+0x9b/0xc0
__local_bh_enable+0x10d/0x170
__local_bh_enable_ip+0xfb/0x150
rcu_do_batch+0x595/0xc40
rcu_cpu_kthread+0x4e9/0x830
smpboot_thread_fn+0x24d/0x3b0
kthread+0x3bd/0x410
ret_from_fork+0x35/0x40
ret_from_fork_asm+0x1a/0x30
write to 0xffff96b95f42d8d8 of 1 bytes by task 88 on cpu 8:
rcu_preempt_deferred_qs_handler+0x1e/0x30
irq_work_single+0xaf/0x160
run_irq_workd+0x91/0xc0
smpboot_thread_fn+0x24d/0x3b0
kthread+0x3bd/0x410
ret_from_fork+0x35/0x40
ret_from_fork_asm+0x1a/0x30
no locks held by irq_work/8/88.
irq event stamp: 200272
hardirqs last enabled at (200272): [<ffffffffb0f56121>] finish_task_switch+0x131/0x320
hardirqs last disabled at (200271): [<ffffffffb25c7859>] __schedule+0x129/0xd70
softirqs last enabled at (0): [<ffffffffb0ee093f>] copy_process+0x4df/0x1cc0
softirqs last disabled at (0): [<0000000000000000>] 0x0
------------------------------------------------------------------------
The problem is that irq-work handlers run with interrupts enabled, which
means that rcu_preempt_deferred_qs_handler() could be interrupted,
and that interrupt handler might contain an RCU read-side critical
section, which might invoke rcu_read_unlock_special(). In the strict
KCSAN mode of operation used by RCU, this constitutes a data race on
the ->defer_qs_iw_pending field.
This commit therefore disables interrupts across the portion of the
rcu_preempt_deferred_qs_handler() that updates the ->defer_qs_iw_pending
field. This suffices because this handler is not a fast path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Correct tid cleanup when tid setup fails
Currently, if any error occurs during ath12k_dp_rx_peer_tid_setup(),
the tid value is already incremented, even though the corresponding
TID is not actually allocated. Proceed to
ath12k_dp_rx_peer_tid_delete() starting from unallocated tid,
which might leads to freeing unallocated TID and cause potential
crash or out-of-bounds access.
Hence, fix by correctly decrementing tid before cleanup to match only
the successfully allocated TIDs.
Also, remove tid-- from failure case of ath12k_dp_rx_peer_frag_setup(),
as decrementing the tid before cleanup in loop will take care of this.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: rockchip: fix kernel hang during smp initialization
In order to bring up secondary CPUs main CPU write trampoline
code to SRAM. The trampoline code is written while secondary
CPUs are powered on (at least that true for RK3188 CPU).
Sometimes that leads to kernel hang. Probably because secondary
CPU execute trampoline code while kernel doesn't expect.
The patch moves SRAM initialization step to the point where all
secondary CPUs are powered down.
That fixes rarely hangs on RK3188:
[ 0.091568] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.091996] rockchip_smp_prepare_cpus: ncores 4 |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Set .migrate_folio in gfs2_{rgrp,meta}_aops
Clears up the warning added in 7ee3647243e5 ("migrate: Remove call to
->writepage") that occurs in various xfstests, causing "something found
in dmesg" failures.
[ 341.136573] gfs2_meta_aops does not implement migrate_folio
[ 341.136953] WARNING: CPU: 1 PID: 36 at mm/migrate.c:944 move_to_new_folio+0x2f8/0x300 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: Fix the sendmsg byte count in siw_tcp_sendpages
Ever since commit c2ff29e99a76 ("siw: Inline do_tcp_sendpages()"),
we have been doing this:
static int siw_tcp_sendpages(struct socket *s, struct page **page, int offset,
size_t size)
[...]
/* Calculate the number of bytes we need to push, for this page
* specifically */
size_t bytes = min_t(size_t, PAGE_SIZE - offset, size);
/* If we can't splice it, then copy it in, as normal */
if (!sendpage_ok(page[i]))
msg.msg_flags &= ~MSG_SPLICE_PAGES;
/* Set the bvec pointing to the page, with len $bytes */
bvec_set_page(&bvec, page[i], bytes, offset);
/* Set the iter to $size, aka the size of the whole sendpages (!!!) */
iov_iter_bvec(&msg.msg_iter, ITER_SOURCE, &bvec, 1, size);
try_page_again:
lock_sock(sk);
/* Sendmsg with $size size (!!!) */
rv = tcp_sendmsg_locked(sk, &msg, size);
This means we've been sending oversized iov_iters and tcp_sendmsg calls
for a while. This has a been a benign bug because sendpage_ok() always
returned true. With the recent slab allocator changes being slowly
introduced into next (that disallow sendpage on large kmalloc
allocations), we have recently hit out-of-bounds crashes, due to slight
differences in iov_iter behavior between the MSG_SPLICE_PAGES and
"regular" copy paths:
(MSG_SPLICE_PAGES)
skb_splice_from_iter
iov_iter_extract_pages
iov_iter_extract_bvec_pages
uses i->nr_segs to correctly stop in its tracks before OoB'ing everywhere
skb_splice_from_iter gets a "short" read
(!MSG_SPLICE_PAGES)
skb_copy_to_page_nocache copy=iov_iter_count
[...]
copy_from_iter
/* this doesn't help */
if (unlikely(iter->count < len))
len = iter->count;
iterate_bvec
... and we run off the bvecs
Fix this by properly setting the iov_iter's byte count, plus sending the
correct byte count to tcp_sendmsg_locked. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: qgroup: fix race between quota disable and quota rescan ioctl
There's a race between a task disabling quotas and another running the
rescan ioctl that can result in a use-after-free of qgroup records from
the fs_info->qgroup_tree rbtree.
This happens as follows:
1) Task A enters btrfs_ioctl_quota_rescan() -> btrfs_qgroup_rescan();
2) Task B enters btrfs_quota_disable() and calls
btrfs_qgroup_wait_for_completion(), which does nothing because at that
point fs_info->qgroup_rescan_running is false (it wasn't set yet by
task A);
3) Task B calls btrfs_free_qgroup_config() which starts freeing qgroups
from fs_info->qgroup_tree without taking the lock fs_info->qgroup_lock;
4) Task A enters qgroup_rescan_zero_tracking() which starts iterating
the fs_info->qgroup_tree tree while holding fs_info->qgroup_lock,
but task B is freeing qgroup records from that tree without holding
the lock, resulting in a use-after-free.
Fix this by taking fs_info->qgroup_lock at btrfs_free_qgroup_config().
Also at btrfs_qgroup_rescan() don't start the rescan worker if quotas
were already disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: core: config: Prevent OOB read in SS endpoint companion parsing
usb_parse_ss_endpoint_companion() checks descriptor type before length,
enabling a potentially odd read outside of the buffer size.
Fix this up by checking the size first before looking at any of the
fields in the descriptor. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: add null check
[WHY]
Prevents null pointer dereferences to enhance function robustness
[HOW]
Adds early null check and return false if invalid. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: APEI: send SIGBUS to current task if synchronous memory error not recovered
If a synchronous error is detected as a result of user-space process
triggering a 2-bit uncorrected error, the CPU will take a synchronous
error exception such as Synchronous External Abort (SEA) on Arm64. The
kernel will queue a memory_failure() work which poisons the related
page, unmaps the page, and then sends a SIGBUS to the process, so that
a system wide panic can be avoided.
However, no memory_failure() work will be queued when abnormal
synchronous errors occur. These errors can include situations like
invalid PA, unexpected severity, no memory failure config support,
invalid GUID section, etc. In such a case, the user-space process will
trigger SEA again. This loop can potentially exceed the platform
firmware threshold or even trigger a kernel hard lockup, leading to a
system reboot.
Fix it by performing a force kill if no memory_failure() work is queued
for synchronous errors.
[ rjw: Changelog edits ] |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ctnetlink: remove refcounting in expectation dumpers
Same pattern as previous patch: do not keep the expectation object
alive via refcount, only store a cookie value and then use that
as the skip hint for dump resumption.
AFAICS this has the same issue as the one resolved in the conntrack
dumper, when we do
if (!refcount_inc_not_zero(&exp->use))
to increment the refcount, there is a chance that exp == last, which
causes a double-increment of the refcount and subsequent memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: timer: fix ida_free call while not allocated
In the snd_utimer_create() function, if the kasprintf() function return
NULL, snd_utimer_put_id() will be called, finally use ida_free()
to free the unallocated id 0.
the syzkaller reported the following information:
------------[ cut here ]------------
ida_free called for id=0 which is not allocated.
WARNING: CPU: 1 PID: 1286 at lib/idr.c:592 ida_free+0x1fd/0x2f0 lib/idr.c:592
Modules linked in:
CPU: 1 UID: 0 PID: 1286 Comm: syz-executor164 Not tainted 6.15.8 #3 PREEMPT(lazy)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-4.fc42 04/01/2014
RIP: 0010:ida_free+0x1fd/0x2f0 lib/idr.c:592
Code: f8 fc 41 83 fc 3e 76 69 e8 70 b2 f8 (...)
RSP: 0018:ffffc900007f79c8 EFLAGS: 00010282
RAX: 0000000000000000 RBX: 1ffff920000fef3b RCX: ffffffff872176a5
RDX: ffff88800369d200 RSI: 0000000000000000 RDI: ffff88800369d200
RBP: 0000000000000000 R08: ffffffff87ba60a5 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000002 R14: 0000000000000000 R15: 0000000000000000
FS: 00007f6f1abc1740(0000) GS:ffff8880d76a0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f6f1ad7a784 CR3: 000000007a6e2000 CR4: 00000000000006f0
Call Trace:
<TASK>
snd_utimer_put_id sound/core/timer.c:2043 [inline] [snd_timer]
snd_utimer_create+0x59b/0x6a0 sound/core/timer.c:2184 [snd_timer]
snd_utimer_ioctl_create sound/core/timer.c:2202 [inline] [snd_timer]
__snd_timer_user_ioctl.isra.0+0x724/0x1340 sound/core/timer.c:2287 [snd_timer]
snd_timer_user_ioctl+0x75/0xc0 sound/core/timer.c:2298 [snd_timer]
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl fs/ioctl.c:893 [inline]
__x64_sys_ioctl+0x198/0x200 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x7b/0x160 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x76/0x7e
[...]
The utimer->id should be set properly before the kasprintf() function,
ensures the snd_utimer_put_id() function will free the allocated id. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: Make cake_enqueue return NET_XMIT_CN when past buffer_limit
The following setup can trigger a WARNING in htb_activate due to
the condition: !cl->leaf.q->q.qlen
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: htb default 1
tc class add dev lo parent 1: classid 1:1 \
htb rate 64bit
tc qdisc add dev lo parent 1:1 handle f: \
cake memlimit 1b
ping -I lo -f -c1 -s64 -W0.001 127.0.0.1
This is because the low memlimit leads to a low buffer_limit, which
causes packet dropping. However, cake_enqueue still returns
NET_XMIT_SUCCESS, causing htb_enqueue to call htb_activate with an
empty child qdisc. We should return NET_XMIT_CN when packets are
dropped from the same tin and flow.
I do not believe return value of NET_XMIT_CN is necessary for packet
drops in the case of ack filtering, as that is meant to optimize
performance, not to signal congestion. |
