| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix rbtree traversal bug in ext4_mb_use_preallocated
During allocations, while looking for preallocations(PA) in the per
inode rbtree, we can't do a direct traversal of the tree because
ext4_mb_discard_group_preallocation() can paralelly mark the pa deleted
and that can cause direct traversal to skip some entries. This was
leading to a BUG_ON() being hit [1] when we missed a PA that could satisfy
our request and ultimately tried to create a new PA that would overlap
with the missed one.
To makes sure we handle that case while still keeping the performance of
the rbtree, we make use of the fact that the only pa that could possibly
overlap the original goal start is the one that satisfies the below
conditions:
1. It must have it's logical start immediately to the left of
(ie less than) original logical start.
2. It must not be deleted
To find this pa we use the following traversal method:
1. Descend into the rbtree normally to find the immediate neighboring
PA. Here we keep descending irrespective of if the PA is deleted or if
it overlaps with our request etc. The goal is to find an immediately
adjacent PA.
2. If the found PA is on right of original goal, use rb_prev() to find
the left adjacent PA.
3. Check if this PA is deleted and keep moving left with rb_prev() until
a non deleted PA is found.
4. This is the PA we are looking for. Now we can check if it can satisfy
the original request and proceed accordingly.
This approach also takes care of having deleted PAs in the tree.
(While we are at it, also fix a possible overflow bug in calculating the
end of a PA)
[1] https://lore.kernel.org/linux-ext4/CA+G9fYv2FRpLqBZf34ZinR8bU2_ZRAUOjKAD3+tKRFaEQHtt8Q@mail.gmail.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Fix dropping valid root bus resources with .end = zero
On r8a7791/koelsch:
kmemleak: 1 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xc3a34e00 (size 64):
comm "swapper/0", pid 1, jiffies 4294937460 (age 199.080s)
hex dump (first 32 bytes):
b4 5d 81 f0 b4 5d 81 f0 c0 b0 a2 c3 00 00 00 00 .]...]..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<fe3aa979>] __kmalloc+0xf0/0x140
[<34bd6bc0>] resource_list_create_entry+0x18/0x38
[<767046bc>] pci_add_resource_offset+0x20/0x68
[<b3f3edf2>] devm_of_pci_get_host_bridge_resources.constprop.0+0xb0/0x390
When coalescing two resources for a contiguous aperture, the second
resource is enlarged to cover the full contiguous range, while the first
resource is marked invalid. This invalidation is done by clearing the
flags, start, and end members.
When adding the initial resources to the bus later, invalid resources are
skipped. Unfortunately, the check for an invalid resource considers only
the end member, causing false positives.
E.g. on r8a7791/koelsch, root bus resource 0 ("bus 00") is skipped, and no
longer registered with pci_bus_insert_busn_res() (causing the memory leak),
nor printed:
pci-rcar-gen2 ee090000.pci: host bridge /soc/pci@ee090000 ranges:
pci-rcar-gen2 ee090000.pci: MEM 0x00ee080000..0x00ee08ffff -> 0x00ee080000
pci-rcar-gen2 ee090000.pci: PCI: revision 11
pci-rcar-gen2 ee090000.pci: PCI host bridge to bus 0000:00
-pci_bus 0000:00: root bus resource [bus 00]
pci_bus 0000:00: root bus resource [mem 0xee080000-0xee08ffff]
Fix this by only skipping resources where all of the flags, start, and end
members are zero. |
| In the Linux kernel, the following vulnerability has been resolved:
usb-storage: alauda: Fix uninit-value in alauda_check_media()
Syzbot got KMSAN to complain about access to an uninitialized value in
the alauda subdriver of usb-storage:
BUG: KMSAN: uninit-value in alauda_transport+0x462/0x57f0
drivers/usb/storage/alauda.c:1137
CPU: 0 PID: 12279 Comm: usb-storage Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
__msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
alauda_check_media+0x344/0x3310 drivers/usb/storage/alauda.c:460
The problem is that alauda_check_media() doesn't verify that its USB
transfer succeeded before trying to use the received data. What
should happen if the transfer fails isn't entirely clear, but a
reasonably conservative approach is to pretend that no media is
present.
A similar problem exists in a usb_stor_dbg() call in
alauda_get_media_status(). In this case, when an error occurs the
call is redundant, because usb_stor_ctrl_transfer() already will print
a debugging message.
Finally, unrelated to the uninitialized memory access, is the fact
that alauda_check_media() performs DMA to a buffer on the stack.
Fortunately usb-storage provides a general purpose DMA-able buffer for
uses like this. We'll use it instead. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dpu: Disallow unallocated resources to be returned
In the event that the topology requests resources that have not been
created by the system (because they are typically not represented in
dpu_mdss_cfg ^1), the resource(s) in global_state (in this case DSC
blocks, until their allocation/assignment is being sanity-checked in
"drm/msm/dpu: Reject topologies for which no DSC blocks are available")
remain NULL but will still be returned out of
dpu_rm_get_assigned_resources, where the caller expects to get an array
containing num_blks valid pointers (but instead gets these NULLs).
To prevent this from happening, where null-pointer dereferences
typically result in a hard-to-debug platform lockup, num_blks shouldn't
increase past NULL blocks and will print an error and break instead.
After all, max_blks represents the static size of the maximum number of
blocks whereas the actual amount varies per platform.
^1: which can happen after a git rebase ended up moving additions to
_dpu_cfg to a different struct which has the same patch context.
Patchwork: https://patchwork.freedesktop.org/patch/517636/ |
| In the Linux kernel, the following vulnerability has been resolved:
vmci_host: fix a race condition in vmci_host_poll() causing GPF
During fuzzing, a general protection fault is observed in
vmci_host_poll().
general protection fault, probably for non-canonical address 0xdffffc0000000019: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x00000000000000c8-0x00000000000000cf]
RIP: 0010:__lock_acquire+0xf3/0x5e00 kernel/locking/lockdep.c:4926
<- omitting registers ->
Call Trace:
<TASK>
lock_acquire+0x1a4/0x4a0 kernel/locking/lockdep.c:5672
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0xb3/0x100 kernel/locking/spinlock.c:162
add_wait_queue+0x3d/0x260 kernel/sched/wait.c:22
poll_wait include/linux/poll.h:49 [inline]
vmci_host_poll+0xf8/0x2b0 drivers/misc/vmw_vmci/vmci_host.c:174
vfs_poll include/linux/poll.h:88 [inline]
do_pollfd fs/select.c:873 [inline]
do_poll fs/select.c:921 [inline]
do_sys_poll+0xc7c/0x1aa0 fs/select.c:1015
__do_sys_ppoll fs/select.c:1121 [inline]
__se_sys_ppoll+0x2cc/0x330 fs/select.c:1101
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x4e/0xa0 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Example thread interleaving that causes the general protection fault
is as follows:
CPU1 (vmci_host_poll) CPU2 (vmci_host_do_init_context)
----- -----
// Read uninitialized context
context = vmci_host_dev->context;
// Initialize context
vmci_host_dev->context = vmci_ctx_create();
vmci_host_dev->ct_type = VMCIOBJ_CONTEXT;
if (vmci_host_dev->ct_type == VMCIOBJ_CONTEXT) {
// Dereferencing the wrong pointer
poll_wait(..., &context->host_context);
}
In this scenario, vmci_host_poll() reads vmci_host_dev->context first,
and then reads vmci_host_dev->ct_type to check that
vmci_host_dev->context is initialized. However, since these two reads
are not atomically executed, there is a chance of a race condition as
described above.
To fix this race condition, read vmci_host_dev->context after checking
the value of vmci_host_dev->ct_type so that vmci_host_poll() always
reads an initialized context. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix race between balance and cancel/pause
Syzbot reported a panic that looks like this:
assertion failed: fs_info->exclusive_operation == BTRFS_EXCLOP_BALANCE_PAUSED, in fs/btrfs/ioctl.c:465
------------[ cut here ]------------
kernel BUG at fs/btrfs/messages.c:259!
RIP: 0010:btrfs_assertfail+0x2c/0x30 fs/btrfs/messages.c:259
Call Trace:
<TASK>
btrfs_exclop_balance fs/btrfs/ioctl.c:465 [inline]
btrfs_ioctl_balance fs/btrfs/ioctl.c:3564 [inline]
btrfs_ioctl+0x531e/0x5b30 fs/btrfs/ioctl.c:4632
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x197/0x210 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The reproducer is running a balance and a cancel or pause in parallel.
The way balance finishes is a bit wonky, if we were paused we need to
save the balance_ctl in the fs_info, but clear it otherwise and cleanup.
However we rely on the return values being specific errors, or having a
cancel request or no pause request. If balance completes and returns 0,
but we have a pause or cancel request we won't do the appropriate
cleanup, and then the next time we try to start a balance we'll trip
this ASSERT.
The error handling is just wrong here, we always want to clean up,
unless we got -ECANCELLED and we set the appropriate pause flag in the
exclusive op. With this patch the reproducer ran for an hour without
tripping, previously it would trip in less than a few minutes. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: compress: fix to call f2fs_wait_on_page_writeback() in f2fs_write_raw_pages()
BUG_ON() will be triggered when writing files concurrently,
because the same page is writtenback multiple times.
1597 void folio_end_writeback(struct folio *folio)
1598 {
......
1618 if (!__folio_end_writeback(folio))
1619 BUG();
......
1625 }
kernel BUG at mm/filemap.c:1619!
Call Trace:
<TASK>
f2fs_write_end_io+0x1a0/0x370
blk_update_request+0x6c/0x410
blk_mq_end_request+0x15/0x130
blk_complete_reqs+0x3c/0x50
__do_softirq+0xb8/0x29b
? sort_range+0x20/0x20
run_ksoftirqd+0x19/0x20
smpboot_thread_fn+0x10b/0x1d0
kthread+0xde/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
Below is the concurrency scenario:
[Process A] [Process B] [Process C]
f2fs_write_raw_pages()
- redirty_page_for_writepage()
- unlock page()
f2fs_do_write_data_page()
- lock_page()
- clear_page_dirty_for_io()
- set_page_writeback() [1st writeback]
.....
- unlock page()
generic_perform_write()
- f2fs_write_begin()
- wait_for_stable_page()
- f2fs_write_end()
- set_page_dirty()
- lock_page()
- f2fs_do_write_data_page()
- set_page_writeback() [2st writeback]
This problem was introduced by the previous commit 7377e853967b ("f2fs:
compress: fix potential deadlock of compress file"). All pagelocks were
released in f2fs_write_raw_pages(), but whether the page was
in the writeback state was ignored in the subsequent writing process.
Let's fix it by waiting for the page to writeback before writing. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: Fix memory leak when handling surveys
When removing a rt2x00 device, its associated channel surveys
are not freed, causing a memory leak observable with kmemleak:
unreferenced object 0xffff9620f0881a00 (size 512):
comm "systemd-udevd", pid 2290, jiffies 4294906974 (age 33.768s)
hex dump (first 32 bytes):
70 44 12 00 00 00 00 00 92 8a 00 00 00 00 00 00 pD..............
00 00 00 00 00 00 00 00 ab 87 01 00 00 00 00 00 ................
backtrace:
[<ffffffffb0ed858b>] __kmalloc+0x4b/0x130
[<ffffffffc1b0f29b>] rt2800_probe_hw+0xc2b/0x1380 [rt2800lib]
[<ffffffffc1a9496e>] rt2800usb_probe_hw+0xe/0x60 [rt2800usb]
[<ffffffffc1ae491a>] rt2x00lib_probe_dev+0x21a/0x7d0 [rt2x00lib]
[<ffffffffc1b3b83e>] rt2x00usb_probe+0x1be/0x980 [rt2x00usb]
[<ffffffffc05981e2>] usb_probe_interface+0xe2/0x310 [usbcore]
[<ffffffffb13be2d5>] really_probe+0x1a5/0x410
[<ffffffffb13be5c8>] __driver_probe_device+0x78/0x180
[<ffffffffb13be6fe>] driver_probe_device+0x1e/0x90
[<ffffffffb13be972>] __driver_attach+0xd2/0x1c0
[<ffffffffb13bbc57>] bus_for_each_dev+0x77/0xd0
[<ffffffffb13bd2a2>] bus_add_driver+0x112/0x210
[<ffffffffb13bfc6c>] driver_register+0x5c/0x120
[<ffffffffc0596ae8>] usb_register_driver+0x88/0x150 [usbcore]
[<ffffffffb0c011c4>] do_one_initcall+0x44/0x220
[<ffffffffb0d6134c>] do_init_module+0x4c/0x220
Fix this by freeing the channel surveys on device removal.
Tested with a RT3070 based USB wireless adapter. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: Add missing hw_ops->get_ring_selector() for IPQ5018
During sending data after clients connected, hw_ops->get_ring_selector()
will be called. But for IPQ5018, this member isn't set, and the
following NULL pointer exception will be occurred:
[ 38.840478] 8<--- cut here ---
[ 38.840517] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 38.923161] PC is at 0x0
[ 38.927930] LR is at ath11k_dp_tx+0x70/0x730 [ath11k]
...
[ 39.063264] Process hostapd (pid: 1034, stack limit = 0x801ceb3d)
[ 39.068994] Stack: (0x856a9a68 to 0x856aa000)
...
[ 39.438467] [<7f323804>] (ath11k_dp_tx [ath11k]) from [<7f314e6c>] (ath11k_mac_op_tx+0x80/0x190 [ath11k])
[ 39.446607] [<7f314e6c>] (ath11k_mac_op_tx [ath11k]) from [<7f17dbe0>] (ieee80211_handle_wake_tx_queue+0x7c/0xc0 [mac80211])
[ 39.456162] [<7f17dbe0>] (ieee80211_handle_wake_tx_queue [mac80211]) from [<7f174450>] (ieee80211_probereq_get+0x584/0x704 [mac80211])
[ 39.467443] [<7f174450>] (ieee80211_probereq_get [mac80211]) from [<7f178c40>] (ieee80211_tx_prepare_skb+0x1f8/0x248 [mac80211])
[ 39.479334] [<7f178c40>] (ieee80211_tx_prepare_skb [mac80211]) from [<7f179e28>] (__ieee80211_subif_start_xmit+0x32c/0x3d4 [mac80211])
[ 39.491053] [<7f179e28>] (__ieee80211_subif_start_xmit [mac80211]) from [<7f17af08>] (ieee80211_tx_control_port+0x19c/0x288 [mac80211])
[ 39.502946] [<7f17af08>] (ieee80211_tx_control_port [mac80211]) from [<7f0fc704>] (nl80211_tx_control_port+0x174/0x1d4 [cfg80211])
[ 39.515017] [<7f0fc704>] (nl80211_tx_control_port [cfg80211]) from [<808ceac4>] (genl_rcv_msg+0x154/0x340)
[ 39.526814] [<808ceac4>] (genl_rcv_msg) from [<808cdb74>] (netlink_rcv_skb+0xb8/0x11c)
[ 39.536446] [<808cdb74>] (netlink_rcv_skb) from [<808ce1d0>] (genl_rcv+0x28/0x34)
[ 39.544344] [<808ce1d0>] (genl_rcv) from [<808cd234>] (netlink_unicast+0x174/0x274)
[ 39.551895] [<808cd234>] (netlink_unicast) from [<808cd510>] (netlink_sendmsg+0x1dc/0x440)
[ 39.559362] [<808cd510>] (netlink_sendmsg) from [<808596e0>] (____sys_sendmsg+0x1a8/0x1fc)
[ 39.567697] [<808596e0>] (____sys_sendmsg) from [<8085b1a8>] (___sys_sendmsg+0xa4/0xdc)
[ 39.575941] [<8085b1a8>] (___sys_sendmsg) from [<8085b310>] (sys_sendmsg+0x44/0x74)
[ 39.583841] [<8085b310>] (sys_sendmsg) from [<80300060>] (ret_fast_syscall+0x0/0x40)
...
[ 39.620734] Code: bad PC value
[ 39.625869] ---[ end trace 8aef983ad3cbc032 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix warning in trace_buffered_event_disable()
Warning happened in trace_buffered_event_disable() at
WARN_ON_ONCE(!trace_buffered_event_ref)
Call Trace:
? __warn+0xa5/0x1b0
? trace_buffered_event_disable+0x189/0x1b0
__ftrace_event_enable_disable+0x19e/0x3e0
free_probe_data+0x3b/0xa0
unregister_ftrace_function_probe_func+0x6b8/0x800
event_enable_func+0x2f0/0x3d0
ftrace_process_regex.isra.0+0x12d/0x1b0
ftrace_filter_write+0xe6/0x140
vfs_write+0x1c9/0x6f0
[...]
The cause of the warning is in __ftrace_event_enable_disable(),
trace_buffered_event_enable() was called once while
trace_buffered_event_disable() was called twice.
Reproduction script show as below, for analysis, see the comments:
```
#!/bin/bash
cd /sys/kernel/tracing/
# 1. Register a 'disable_event' command, then:
# 1) SOFT_DISABLED_BIT was set;
# 2) trace_buffered_event_enable() was called first time;
echo 'cmdline_proc_show:disable_event:initcall:initcall_finish' > \
set_ftrace_filter
# 2. Enable the event registered, then:
# 1) SOFT_DISABLED_BIT was cleared;
# 2) trace_buffered_event_disable() was called first time;
echo 1 > events/initcall/initcall_finish/enable
# 3. Try to call into cmdline_proc_show(), then SOFT_DISABLED_BIT was
# set again!!!
cat /proc/cmdline
# 4. Unregister the 'disable_event' command, then:
# 1) SOFT_DISABLED_BIT was cleared again;
# 2) trace_buffered_event_disable() was called second time!!!
echo '!cmdline_proc_show:disable_event:initcall:initcall_finish' > \
set_ftrace_filter
```
To fix it, IIUC, we can change to call trace_buffered_event_enable() at
fist time soft-mode enabled, and call trace_buffered_event_disable() at
last time soft-mode disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: tpm_tis: Add the missed acpi_put_table() to fix memory leak
In check_acpi_tpm2(), we get the TPM2 table just to make
sure the table is there, not used after the init, so the
acpi_put_table() should be added to release the ACPI memory. |
| In the Linux kernel, the following vulnerability has been resolved:
ext2: Add sanity checks for group and filesystem size
Add sanity check that filesystem size does not exceed the underlying
device size and that group size is big enough so that metadata can fit
into it. This avoid trying to mount some crafted filesystems with
extremely large group counts. |
| Improper resource release in the call termination process in AWS Wickr before version 6.62.13 on Windows, macOS and Linux may allow a call participant to continue receiving audio input from another user after they close their call window. This issue occurs under certain conditions, which require the affected user to take a particular action within the application
To mitigate this issue, users should upgrade AWS Wickr, Wickr Gov and Wickr Enterprise desktop version to version 6.62.13. |
| VestaCP commit a3f0fa1 (2018-05-31) up to commit ee03eff (2018-06-13) contain embedded malicious code that resulted in a supply-chain compromise. New installations created from the compromised installer since at least May 2018 were subject to installation of Linux/ChachaDDoS, a multi-stage DDoS bot that uses Lua for second- and third-stage components. The compromise leaked administrative credentials (base64-encoded admin password and server domain) to an external URL during installation and/or resulted in the installer dropping and executing a DDoS malware payload under local system privileges. Compromised servers were subsequently observed participating in large-scale DDoS activity. Vesta acknowledged exploitation in the wild in October 2018. |
| In the Linux kernel, the following vulnerability has been resolved:
ovl: fix null pointer dereference in ovl_get_acl_rcu()
Following process:
P1 P2
path_openat
link_path_walk
may_lookup
inode_permission(rcu)
ovl_permission
acl_permission_check
check_acl
get_cached_acl_rcu
ovl_get_inode_acl
realinode = ovl_inode_real(ovl_inode)
drop_cache
__dentry_kill(ovl_dentry)
iput(ovl_inode)
ovl_destroy_inode(ovl_inode)
dput(oi->__upperdentry)
dentry_kill(upperdentry)
dentry_unlink_inode
upperdentry->d_inode = NULL
ovl_inode_upper
upperdentry = ovl_i_dentry_upper(ovl_inode)
d_inode(upperdentry) // returns NULL
IS_POSIXACL(realinode) // NULL pointer dereference
, will trigger an null pointer dereference at realinode:
[ 205.472797] BUG: kernel NULL pointer dereference, address:
0000000000000028
[ 205.476701] CPU: 2 PID: 2713 Comm: ls Not tainted
6.3.0-12064-g2edfa098e750-dirty #1216
[ 205.478754] RIP: 0010:do_ovl_get_acl+0x5d/0x300
[ 205.489584] Call Trace:
[ 205.489812] <TASK>
[ 205.490014] ovl_get_inode_acl+0x26/0x30
[ 205.490466] get_cached_acl_rcu+0x61/0xa0
[ 205.490908] generic_permission+0x1bf/0x4e0
[ 205.491447] ovl_permission+0x79/0x1b0
[ 205.491917] inode_permission+0x15e/0x2c0
[ 205.492425] link_path_walk+0x115/0x550
[ 205.493311] path_lookupat.isra.0+0xb2/0x200
[ 205.493803] filename_lookup+0xda/0x240
[ 205.495747] vfs_fstatat+0x7b/0xb0
Fetch a reproducer in [Link].
Use the helper ovl_i_path_realinode() to get realinode and then do
non-nullptr checking. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4: Fix a credential leak in _nfs4_discover_trunking() |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: Fix xid leak in cifs_ses_add_channel()
Before return, should free the xid, otherwise, the
xid will be leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix potential null deref in ext4_mb_init()
In ext4_mb_init(), ext4_mb_avg_fragment_size_destroy() may be called
when sbi->s_mb_avg_fragment_size remains uninitialized (e.g., if groupinfo
slab cache allocation fails). Since ext4_mb_avg_fragment_size_destroy()
lacks null pointer checking, this leads to a null pointer dereference.
==================================================================
EXT4-fs: no memory for groupinfo slab cache
BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 0 P4D 0
Oops: Oops: 0002 [#1] SMP PTI
CPU:2 UID: 0 PID: 87 Comm:mount Not tainted 6.17.0-rc2 #1134 PREEMPT(none)
RIP: 0010:_raw_spin_lock_irqsave+0x1b/0x40
Call Trace:
<TASK>
xa_destroy+0x61/0x130
ext4_mb_init+0x483/0x540
__ext4_fill_super+0x116d/0x17b0
ext4_fill_super+0xd3/0x280
get_tree_bdev_flags+0x132/0x1d0
vfs_get_tree+0x29/0xd0
do_new_mount+0x197/0x300
__x64_sys_mount+0x116/0x150
do_syscall_64+0x50/0x1c0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
==================================================================
Therefore, add necessary null check to ext4_mb_avg_fragment_size_destroy()
to prevent this issue. The same fix is also applied to
ext4_mb_largest_free_orders_destroy(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: dont report verifier bug for missing bpf_scc_visit on speculative path
Syzbot generated a program that triggers a verifier_bug() call in
maybe_exit_scc(). maybe_exit_scc() assumes that, when called for a
state with insn_idx in some SCC, there should be an instance of struct
bpf_scc_visit allocated for that SCC. Turns out the assumption does
not hold for speculative execution paths. See example in the next
patch.
maybe_scc_exit() is called from update_branch_counts() for states that
reach branch count of zero, meaning that path exploration for a
particular path is finished. Path exploration can finish in one of
three ways:
a. Verification error is found. In this case, update_branch_counts()
is called only for non-speculative paths.
b. Top level BPF_EXIT is reached. Such instructions are never a part of
an SCC, so compute_scc_callchain() in maybe_scc_exit() will return
false, and maybe_scc_exit() will return early.
c. A checkpoint is reached and matched. Checkpoints are created by
is_state_visited(), which calls maybe_enter_scc(), which allocates
bpf_scc_visit instances for checkpoints within SCCs.
Hence, for non-speculative symbolic execution paths, the assumption
still holds: if maybe_scc_exit() is called for a state within an SCC,
bpf_scc_visit instance must exist.
This patch removes the verifier_bug() call for speculative paths. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: lan78xx: Fix lost EEPROM read timeout error(-ETIMEDOUT) in lan78xx_read_raw_eeprom
Syzbot reported read of uninitialized variable BUG with following call stack.
lan78xx 8-1:1.0 (unnamed net_device) (uninitialized): EEPROM read operation timeout
=====================================================
BUG: KMSAN: uninit-value in lan78xx_read_eeprom drivers/net/usb/lan78xx.c:1095 [inline]
BUG: KMSAN: uninit-value in lan78xx_init_mac_address drivers/net/usb/lan78xx.c:1937 [inline]
BUG: KMSAN: uninit-value in lan78xx_reset+0x999/0x2cd0 drivers/net/usb/lan78xx.c:3241
lan78xx_read_eeprom drivers/net/usb/lan78xx.c:1095 [inline]
lan78xx_init_mac_address drivers/net/usb/lan78xx.c:1937 [inline]
lan78xx_reset+0x999/0x2cd0 drivers/net/usb/lan78xx.c:3241
lan78xx_bind+0x711/0x1690 drivers/net/usb/lan78xx.c:3766
lan78xx_probe+0x225c/0x3310 drivers/net/usb/lan78xx.c:4707
Local variable sig.i.i created at:
lan78xx_read_eeprom drivers/net/usb/lan78xx.c:1092 [inline]
lan78xx_init_mac_address drivers/net/usb/lan78xx.c:1937 [inline]
lan78xx_reset+0x77e/0x2cd0 drivers/net/usb/lan78xx.c:3241
lan78xx_bind+0x711/0x1690 drivers/net/usb/lan78xx.c:3766
The function lan78xx_read_raw_eeprom failed to properly propagate EEPROM
read timeout errors (-ETIMEDOUT). In the fallthrough path, it first
attempted to restore the pin configuration for LED outputs and then
returned only the status of that restore operation, discarding the
original timeout error.
As a result, callers could mistakenly treat the data buffer as valid
even though the EEPROM read had actually timed out with no data or partial
data.
To fix this, handle errors in restoring the LED pin configuration separately.
If the restore succeeds, return any prior EEPROM timeout error correctly
to the caller. |
