| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: bound pg_{temp,upmap,upmap_items} length to CEPH_PG_MAX_SIZE
__decode_pg_temp() decodes an user-controlled length but only rejects
values large enough to overflow the allocation; it does not bound it to
CEPH_PG_MAX_SIZE. The helper backs both pg_temp and pg_upmap decoding, and
apply_upmap()/get_temp_osds() later copy the decoded list into the fixed-size
on-stack array struct ceph_osds.osds[CEPH_PG_MAX_SIZE]. A monitor that sends
an OSDMap with a pg_temp/pg_upmap entry longer than 32 thus causes a stack
out-of-bounds write.
An OSD set for a single PG can never exceed CEPH_PG_MAX_SIZE, so reject longer
entries at decode time. The bound is well below the old overflow threshold, so
it also covers the allocation-size overflow the previous check guarded against.
BUG: KASAN: stack-out-of-bounds in ceph_pg_to_up_acting_osds
Write of size 4 ... by task exploit
kasan_report (mm/kasan/report.c:595)
ceph_pg_to_up_acting_osds (net/ceph/osdmap.c:2617 net/ceph/osdmap.c:2833)
calc_target (net/ceph/osd_client.c:1638)
__submit_request (net/ceph/osd_client.c:2394)
ceph_osdc_start_request (net/ceph/osd_client.c:2490)
ceph_osdc_call (net/ceph/osd_client.c:5164)
rbd_dev_image_probe (drivers/block/rbd.c:6899)
do_rbd_add (drivers/block/rbd.c:7138)
...
kernel BUG at net/ceph/osdmap.c:2670!
[ idryomov: do the same in __decode_pg_upmap_items() ] |
| In the Linux kernel, the following vulnerability has been resolved:
amt: fix use-after-free in AMT delayed works
When an AMT device is removed, pending delayed works can still access
the freed amt_dev structure, which may result in kernel crashes or
memory corruption.
amt_dev_stop() cancels req_wq and discovery_wq with
cancel_delayed_work_sync(), but these works can be scheduled again
from event_wq after the cancellation. This allows delayed works to
access the freed amt_dev structure after the netdev has been released.
The following is a simple race scenario:
CPU0 CPU1
amt_dev_stop()
cancel_delayed_work_sync()
amt_event_work()
mod_delayed_work(req_wq)
free netdev
req_wq accesses freed amt_dev
Use disable_delayed_work_sync() in amt_dev_stop() to prevent req_wq and
discovery_wq from being queued again and wait for running work items
to complete.
The delayed works are disabled after initialization in
amt_newlink() and enabled only when the device is successfully opened.
This keeps the delayed work lifecycle synchronized with the lifetime
of the AMT device. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: preserve ACL_DONT_CACHE state in forget_cached_acl()
The ACL_DONT_CACHE state is meant to be a constant state for the inode
for filesystems that want to opt out of posix acl caching.
Commit facd61053cff1 ("fuse: fixes after adapting to new posix acl api")
used this facility to opt out of posix acl caching for fuse inodes with
fuse server that does not negotiate FUSE_POSIX_ACL (fc->posix_acl).
The commit also takes care to gate the forget_all_cached_acls() call in
fuse_set_acl() on fc->posix_acl because there is no need for it, but
there are other placed in fuse code which call forget_all_cached_acls()
unconditional to fc->posix_acl and those cause the loss of the
ACL_DONT_CACHE state.
This is not only a functional bug. Properly timed, a get_acl() from this
fuse filesystem can return a stale cached value, as was observed in tests,
because set_acl() does not invalidate the unintentional acl cache.
We could fix this in fuse, but it actually makes no sense for the vfs
helper forget_cached_acl() to invalidate the ACL_DONT_CACHE state, so
let it not do that to fix fuse and future users of ACL_DONT_CACHE. |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: fix out-of-bounds bitmap_set() with zero-length range
ifs_set_range_dirty() and ifs_set_range_uptodate() compute last_blk
as (off + len - 1) >> i_blkbits. When off is 0 and len is 0, the
unsigned subtraction underflows to SIZE_MAX, producing a huge
last_blk and nr_blks value that causes bitmap_set() to write far
beyond the ifs->state allocation.
Regarding ifs_set_range_uptodate(), it is temporarily safe because len
cannot be passed in as 0. However, for ifs_set_range_dirty() this is
reachable from __iomap_write_end(): when copy_folio_from_iter_atomic()
returns 0 (e.g. user buffer fault) and the folio is already uptodate,
the guard at the top of __iomap_write_end() does not trigger because
!folio_test_uptodate() is false, and iomap_set_range_dirty() is called
with copied == 0.
Add a !len guard to both functions before the computation, so that a
zero-length range is a no-op. |
| In the Linux kernel, the following vulnerability has been resolved:
net: gro: fix double aggregation of flush-marked skbs
Commit 0ab03f353d36 ("net-gro: Fix GRO flush when receiving a GSO
packet.") added a flush check to skb_gro_receive(), but
skb_gro_receive_list() lacks the same validation.
As a result, packets marked with NAPI_GRO_CB(skb)->flush may still be
re-aggregated.
This allows already-GRO'd packets with existing frag_list to be
re-aggregated into a new GRO session, corrupting the frag_list chain
structure. When skb_segment() attempts to unpack these malformed packets,
it encounters invalid state and triggers a kernel panic.
Scenario (Tethering/Device forwarding):
1. Driver: Generated aggregated packet P1 via LRO with frag_list
2. Dev A: Receives aggregated fraglist packet and flush flag set
3. Dev A: Re-enters GRO, skb_gro_receive_list() is called
4. Missing flush check allows re-aggregation despite flush flag
5. Frag_list chain becomes corrupted (loops or dangling refs)
6. Dev B: TX path calls skb_segment(), crashes on corrupted frag_list
Root cause in skb_segment():
The check at line ~4891:
if (hsize <= 0 && i >= nfrags && skb_headlen(list_skb) &&
(skb_headlen(list_skb) == len || sg)) {
When frag_list is corrupted by double aggregation, when list_skb is
a NULL pointer from skb->next, skb_headlen(list_skb) dereference
NULL/corrupted pointers occurs.
Call Trace:
skb_headlen(NULL skb)
skb_segment
tcp_gso_segment
tcp4_gso_segment
inet_gso_segment
skb_mac_gso_segment
__skb_gso_segment
skb_gso_segment
validate_xmit_skb
validate_xmit_skb_list
sch_direct_xmit
qdisc_restart
__qdisc_run
qdisc_run
net_tx_action
Fix: Add NAPI_GRO_CB(skb)->flush validation to the early-return check in
skb_gro_receive_list(), matching the defensive programming pattern of
skb_gro_receive(). |
| In the Linux kernel, the following vulnerability has been resolved:
ptp: ptp_s390: Add missing facility check
Only register the physical clock when facility 28 is installed
and PTFF QAF returns that PTFF QPT is available. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: reject out-of-range ptype in ice_parser_profile_init
set_bit(rslt->ptype, prof->ptypes) operates on a DECLARE_BITMAP of
ICE_FLOW_PTYPE_MAX (1024) bits. Nothing prevents a malicious VF from
providing ptype >= 1024 through VIRTCHNL, resulting in a write past
the end of the bitmap and a kernel page fault.
Reproduced with a custom kernel module injecting a crafted
VIRTCHNL_OP_ADD_RSS_CFG on E810-C QSFP (8086:1592),
FW 4.91 0x800214af 1.3909.0, ICE COMMS DDP 1.3.53.0,
kernel 7.1.0-rc1.
crash_parser: ice_parser_profile_init @ ffffffffc0d61b60
crash_parser: setting ptype=0xffff (max valid=1023)
crash_parser: calling ice_parser_profile_init -- expect OOB crash!
BUG: kernel NULL pointer dereference, address: 0000000000000000
Oops: Oops: 0002 [#1] SMP NOPTI
CPU: 56 UID: 0 PID: 165011 Comm: insmod Kdump: loaded Tainted: G S U OE 7.1.0-rc1 #1
Hardware name: Intel Corporation S2600BPB/S2600BPB
RIP: 0010:ice_parser_profile_init+0x2d/0x1d0 [ice]
Call Trace:
<TASK>
? __pfx_ice_parser_profile_init+0x10/0x10 [ice]
crash_init+0x127/0xff0 [crash_parser]
do_one_initcall+0x45/0x310
do_init_module+0x64/0x270
init_module_from_file+0xcc/0xf0
idempotent_init_module+0x17b/0x280
__x64_sys_finit_module+0x6e/0xe0
Bail out early with -EINVAL when ptype is out of range. |
| In the Linux kernel, the following vulnerability has been resolved:
rtase: Workaround for TX hang caused by hardware packet parsing
The hardware performs packet parsing before packet transmission.
Parsing incomplete IPv4, IPv6, TCP, or UDP headers may trigger a TX
hang because the hardware parser expects additional protocol header
data that is not present in the packet.
The hardware performs additional PTP parsing on UDP packets identified
by destination ports 319/320 at the expected UDP destination port
offset.
If such a packet has transport data smaller than RTASE_MIN_PAD_LEN,
the hardware parser expects additional packet data and may trigger a
TX hang.
To avoid these hardware issues, the driver applies the following
workarounds.
Drop malformed packets that may trigger this hardware issue before
transmission.
For IPv4 non-initial fragments, the hardware does not check the
fragment offset before parsing the expected transport header location.
As a result, these packets are still subject to transport header
parsing even though they do not contain a transport header. If the
transport data is shorter than the minimum transport header required
by the hardware parser, pad the transport data to the minimum
transport header length required by the hardware parser. Packets that
also match the hardware PTP parsing conditions continue to follow the
corresponding workaround.
For IPv6 fragmented packets, neither of the above hardware issues
occurs because the hardware only continues packet parsing when the
IPv6 Base Header Next Header field directly indicates UDP. Packets
carrying a Fragment Header do not continue through the subsequent
packet parsing stages.
For packets identified for hardware PTP parsing, pad the transport
data so it reaches RTASE_MIN_PAD_LEN before transmission. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: initialize standalone TCP-AO response padding
tcp_v4_send_ack() and tcp_v6_send_response() construct standalone TCP
responses with TCP-AO options. The option length carries the actual MAC
length, but the TCP header length includes the option rounded up to a
four-byte boundary.
tcp_ao_hash_hdr() writes the MAC only. Thus, when the MAC length is not
four-byte aligned, the one to three bytes after the MAC are left
uninitialized and may be transmitted. For the normal TCP-AO hashing
mode, those bytes also have to be initialized before computing the MAC.
Initialize only the alignment padding in the TCP-AO branches, before
hashing the header. Use TCPOPT_NOP, as in the normal TCP-AO output path.
This avoids adding work to non-AO TCP responses while preserving a valid
authenticated header. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: challenge ACK for non-exact RST in SYN-RECEIVED
The SYN-RECEIVED request-socket path in tcp_check_req() accepts an
in-window RST without requiring SEG.SEQ to exactly match RCV.NXT. A
non-exact RST therefore removes the request instead of eliciting a
challenge ACK.
RFC 9293 section 3.10.7.4 applies the RFC 5961 reset check in
SYN-RECEIVED: an exact RST resets the connection, while a non-exact
in-window RST must trigger a challenge ACK and be dropped.
Apply that check before the ACK-field validation, following the RFC
sequence-number, RST, then ACK processing order. Factor the per-netns
challenge ACK quota out of tcp_send_challenge_ack() so request sockets
can share it. Use the request socket's send_ack() callback and its own
out-of-window ACK timestamp to send and rate-limit the response. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: mdb: Fix source list corruption on a failed replace
When replacing the source list of an MDB remote entry, all existing
sources are first marked for deletion and vxlan_mdb_remote_srcs_add()
is then called to add the new source list. Sources present in the new
list have their deletion mark cleared, and any sources left marked
afterwards are removed.
If vxlan_mdb_remote_srcs_add() fails partway through, its error path
deletes all entries on the remote's source list. That rollback is only
correct for its other caller, vxlan_mdb_remote_add(), where the remote
was just allocated and the list contains solely entries added during
the call. On the replace path the list also holds pre-existing sources,
so a failed replace tears them down together with their (S, G)
forwarding entries instead of leaving the entry unchanged.
This is reachable from an existing (*, G) remote. An EXCLUDE filter
that loses sources starts forwarding traffic that should be blocked,
while an INCLUDE filter that loses sources drops traffic that should be
forwarded.
Mark entries created during the current pass with a new
VXLAN_SGRP_F_NEW flag. On failure, delete only those entries and clear
the deletion mark on the pre-existing ones, so a failed replace leaves
the source list untouched. Retain the flag until the whole operation
succeeds and then clear it. Also stop vxlan_mdb_remote_src_add() from
deleting a pre-existing entry it only looked up when adding that
entry's forwarding entry fails. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vcn4: avoid rereading IB param length
Reuse the parameter length returned by
vcn_v4_0_enc_find_ib_param() instead of rereading it from
the IB.
This avoids a potential TOCTOU issue if the IB contents
change between reads.
(cherry picked from commit dbb02b4755f8c1f3773263f2d779872c1c0c073a) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: reject mapping a reserved doorbell to a new queue
When creating an user-queue, the user space
provides a doorbell BO handle and an offset within
the bo to obtain a doorbell.
However current implementation using xa_store_irq()
to store a doorbell, which allows a later queue created
with the same BO and offset parameters to overwrite an
existing queue and doorbell mapping.
This can cause problems like misrouting fence IRQ
processing to a wrong queue, and mislead the cleanup
process of one queue erasing the mapping of another queue.
This commit fixes this issue by replacing xa_store_irq with
xa_insert_irq, which rejects mapping a reserved
doorbell to a newly created queue
(cherry picked from commit 6244eae22966350db52faf9c1369d3b2ffc5de4e) |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate num_subauth when copying ACE in set_ntacl_dacl
set_ntacl_dacl() copies each ACE from the attacker-controlled stored
security descriptor verbatim into the response DACL without checking
sid.num_subauth. The ACE bytes (including an unchecked num_subauth)
originate from an authenticated SMB2_SET_INFO(SecInfo=DACL) that is
stored raw via ksmbd_vfs_set_sd_xattr(); parse_dacl() rejects a bad ACE
with `break` rather than an error, so parse_sec_desc() still returns
success and the malformed SD reaches the xattr intact.
On a subsequent SMB2_QUERY_INFO(SecInfo=DACL) for an inode carrying a
POSIX access ACL, build_sec_desc() -> set_ntacl_dacl() ->
set_posix_acl_entries_dacl() walks the copied ACEs and reads
ntace->sid.sub_auth[ntace->sid.num_subauth - 1]
with num_subauth taken straight from the stored SD. Since sub_auth[]
is fixed at SID_MAX_SUB_AUTHORITIES (15), a crafted num_subauth (e.g.
255) drives an out-of-bounds heap read of ~1 KB with an offset fully
controlled by an authenticated client.
The sibling functions already gate this field:
parse_dacl() -- num_subauth == 0 || > SID_MAX_SUB_AUTHORITIES
parse_sid() -- num_subauth > SID_MAX_SUB_AUTHORITIES
smb_copy_sid() -- min_t(u8, num_subauth, SID_MAX_SUB_AUTHORITIES)
set_ntacl_dacl() is the lone inconsistent path that omits the check.
Add the same num_subauth validation in set_ntacl_dacl() before copying
the ACE, matching the gate already enforced by parse_dacl(). |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: bound DACL dedup walk to copied ACEs
set_ntacl_dacl() can stop copying ACEs before consuming the full input
DACL when size accounting overflows.
When that happens, num_aces reflects only the ACEs that were actually
copied into the output DACL, but set_posix_acl_entries_dacl() still
receives nt_num_aces and uses it to walk the existing ACE array during
dedup.
That makes the dedup walk scan past the copied ACE array and inspect
buffer tail that does not contain valid ACEs.
Split the two meanings currently carried by the NT ACE count. Pass the
number of copied NT ACEs to bound the dedup walk, and preserve the
original "input DACL had NT ACEs" state separately for the
Everyone/default ACL fallback.
This keeps the dedup walk aligned with the ACEs that are actually
present in the rebuilt DACL. |
| In the Linux kernel, the following vulnerability has been resolved:
audit: fix recursive locking deadlock in audit_dupe_exe()
A deadlock occurs in the audit subsystem when duplicating
executable-related rules.
When a file is moved (e.g., via do_renameat2()), the VFS layer locks
the parent directory (I_MUTEX_PARENT), which synchronously triggers an
fsnotify_move event. If an existing executable audit rule matches the
file being moved, the audit subsystem catches this event and calls
audit_dupe_exe() to duplicate the watch and update the rule. Then,
audit_alloc_mark() would call kern_path_parent() to resolve the path,
leading to a blind attempt to acquire the exact same I_MUTEX_PARENT lock
already held by the task, resulting in the following recursive locking
deadlock:
============================================
WARNING: possible recursive locking detected
6.12.0-55.27.1.el10_0.x86_64+debug #1 Not tainted
--------------------------------------------
mv/5099 is trying to acquire lock:
ffff888132845358 (&inode->i_sb->s_type->i_mutex_dir_key/1){+.+.}-{3:3},
at: __kern_path_locked+0x10a/0x2f0
but task is already holding lock:
ffff888132846b58 (&inode->i_sb->s_type->i_mutex_dir_key/1){+.+.}-{3:3},
at: lock_two_directories+0x13f/0x2b0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&inode->i_sb->s_type->i_mutex_dir_key/1);
lock(&inode->i_sb->s_type->i_mutex_dir_key/1);
*** DEADLOCK ***
May be due to missing lock nesting notation
6 locks held by mv/5099:
#0: ffff888112a9c440 (sb_writers#13)
at: do_renameat2+0x34c/0xbc0
#1: ffff888112a9c790 (&type->s_vfs_rename_key#3)
at: do_renameat2+0x415/0xbc0
#2: ffff888132846b58 (&inode->i_sb->s_type->i_mutex_dir_key/1)
at: lock_two_directories+0x13f/0x2b0
#3: ffff888132845358 (&inode->i_sb->s_type->i_mutex_dir_key/5)
at: lock_two_directories+0x175/0x2b0
#4: ffffffffb3a1fb10 (&fsnotify_mark_srcu)
at: fsnotify+0x454/0x28a0
#5: ffffffffaf886230 (audit_filter_mutex)
at: audit_update_watch+0x36/0x11e0
stack backtrace:
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xb0
print_deadlock_bug.cold+0xbd/0xca
validate_chain+0x83a/0xf00
__lock_acquire+0xcac/0x1d20
lock_acquire.part.0+0x11b/0x360
down_write_nested+0x9f/0x230
__kern_path_locked+0x10a/0x2f0
kern_path_locked+0x26/0x40
audit_alloc_mark+0xfb/0x4f0
audit_dupe_exe+0x6c/0xe0
audit_dupe_rule+0x6c2/0xc00
audit_update_watch+0x4cc/0x11e0
audit_watch_handle_event+0x12c/0x1b0
send_to_group+0x5d0/0x8b0
fsnotify+0x615/0x28a0
fsnotify_move+0x1d8/0x630
vfs_rename+0xdcd/0x1df0
do_renameat2+0x9d4/0xbc0
__x64_sys_renameat+0x192/0x260
do_syscall_64+0x92/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f0491fe8c4e
Code: 0f 1f 40 00 48 8b 15 c1 e1 16 00 f7 d8 64 89 02 b8 ff ff ff ff
c3 66 0f 1f 44 00 00 f3 0f 1e fa 49 89 ca b8 08 01 00 00 0f 05 <48>
3d 00 f0 ff ff 77 0a c3 66 0f 1f 84 00 00 00 00 00 48 8b 15 89
RSP: 002b:00007ffc7210bf38 EFLAGS: 00000246 ORIG_RAX: 0000000000000108
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f0491fe8c4e
RDX: 0000000000000003 RSI: 00007ffc7210e6c8 RDI: 00000000ffffff9c
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000001
R10: 00005575eb2dae2a R11: 0000000000000246 R12: 00005575eb2dae2a
R13: 00007ffc7210e6c8 R14: 0000000000000003 R15: 00000000ffffff9c
</TASK>
The aforementioned deadlock can be consistently reproduced by running
the script below:
audit-dupe-exe-deadlock.sh
--------------------------
#!/bin/bash
auditctl -D
mkdir -p /tmp/foo
touch /tmp/file
auditctl -a always,exit -F exe=/tmp/file -F path=/tmp/file -S all -k dr
mv /tmp/file /tmp/foo/file
rm -Rf /tmp/foo
This patch fixes the issue by introducing struct audit_watch_ctx to pass
the fsnotify event context down to audit_alloc_mark(). By utilizing the
already-resolved directory inode provided by the event, we bypass the
kern_path_parent() path resol
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
HID: wacom: stop hardware after post-start probe failures
wacom_parse_and_register() starts HID hardware before registering inputs
and initializing pad LEDs/remotes. Those later steps can fail, but their
error paths currently release Wacom resources without stopping the HID
hardware.
Route post-hid_hw_start() failures through hid_hw_stop() before
releasing driver resources.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix path resolution in ksmbd_vfs_kern_path_create
The SMB2 open lookup is rooted at the share with LOOKUP_BENEATH, but the
create/mkdir/hardlink sink is not: ksmbd_vfs_kern_path_create() builds an
absolute path with convert_to_unix_name() and resolves it from AT_FDCWD
via start_creating_path(), so a ".." component is walked from the real
filesystem root and escapes the export.
An authenticated client races a missing path component so the rooted open
lookup returns -ENOENT (taking the create branch) while the same component
is present (a directory) when the create walk runs; the create then
resolves ".." out of the share.
Root the create walk at the share like the lookup and rename paths already
are: resolve the parent with vfs_path_parent_lookup(..., LOOKUP_BENEATH,
&share_conf->vfs_path) and create the final component with
start_creating_noperm(). convert_to_unix_name() then has no callers and is
removed. |
| Improper input validation in Samsung Plus TV prior to version 1.0.28.6 allows remote attackers to access sensitive information. |
| Improper input validation in Samsung Android USB Driver for Windows prior to version 1.9.5.0 allows local attacker to access out-of-bounds memory. |
