| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
of/overlay: don't leak fragment references when changeset init fails
init_overlay_changeset() stores the number of initialized fragments
in ovcs->count only on full success. When find_target() or the
__symbols__ lookup fails partway through, the target and overlay
references taken for the fragments initialized so far are never
dropped: free_overlay_changeset() bounds its cleanup loop by
ovcs->count, which is still 0.
Store the running count on the error path so free_overlay_changeset()
puts whatever was set up. The store is guarded by ovcs->fragments
because on the allocation-failure path cnt still holds the counting
pass total while there is no fragments array; everywhere else cnt
only counts fully-initialized fragments. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wfx: validate MIB read length before copying to caller
wfx_hif_read_mib() copies reply->length bytes from the firmware
response into the caller-provided buffer without checking that
reply->length does not exceed val_len. A firmware response with
a length field larger than expected overruns the caller buffer and
reads past the end of the reply allocation.
Replace the dead -ENOMEM check with an active validation that
reply->length fits within val_len before the memcpy. |
| In the Linux kernel, the following vulnerability has been resolved:
rtc: mpfs: fix unchecked devm_clk_get() error pointer in probe()
devm_clk_get(&pdev->dev, "rtcref")'s return value was passed straight
into clk_get_rate() without checking it for an error first, unlike the
"rtc" clock a few lines above which is correctly checked with
IS_ERR(). clk_get_rate() only guards against a NULL clk, not an error
pointer:
if (!clk)
return 0;
...
rate = clk_core_get_rate_recalc(clk->core);
so if devm_clk_get() ever returns an error pointer here (for example
ERR_PTR(-EPROBE_DEFER), which is the normal, expected outcome if the
clkcfg clock-provider this RTC depends on has not registered its
clocks yet by the time this driver probes), clk_get_rate() dereferences
that error pointer instead of returning 0, crashing instead of letting
probe defer.
Capture the clock in the existing 'clk' local and check it with
IS_ERR() before calling clk_get_rate(), matching the handling already
used for the "rtc" clock in this same function. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: preserve hidden-group beacon IE ownership
A hidden-group probe-response entry borrows its beacon IEs from the
group's beacon entry. cfg80211_update_assoc_bss_entry() can pass such
an entry to cfg80211_update_known_bss() when merging scan entries
after a channel switch.
Copying the borrowed beacon_ies into the associated entry gives the
same allocation two owners. Releasing the group's beacon entry can
then leave the associated entry pointing to freed IEs, which are
freed again when that entry is released.
Skip beacon IE replacement when the source entry belongs to a hidden
group. Preserve probe-response processing, the subsequent metadata
updates, and the existing rejection path for conflicting hidden
beacon updates. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel: validate DDC record lengths
Parse DDC record lengths in unsigned storage so 0xFF does not wrap.
Reject records smaller than the mandatory three-byte header, records
exceeding U8_MAX, and records exceeding remaining firmware bytes before
issuing Intel_Write_DDC.
This issue was reported by Claude Mythos. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mctp: publish the mctp_dev only after it is initialised
mctp_add_dev() links the new mctp_dev into dev->mctp_ptr before mdev->dev
is assigned, so a reader that picks the device up in that window
dereferences a net_device pointer that is still NULL:
KASAN: null-ptr-deref in range [0x00000000000000b0-0x00000000000000b7]
Call Trace:
<TASK>
? __pfx_mctp_sendmsg (./include/linux/sockptr.h:49)
? __pfx_mctp_dst_output (net/mctp/route.c:41)
? selinux_socket_sendmsg (security/selinux/hooks.c:5278)
____sys_sendmsg (net/socket.c:775 (discriminator 1) net/socket.c:790
(discriminator 1) net/socket.c:2684 (discriminator 1))
? __pfx_____sys_sendmsg (net/socket.c:1131)
? __pfx_copy_msghdr_from_user (net/socket.c:2590)
? update_cfs_rq_load_avg (kernel/sched/fair.c:5478)
___sys_sendmsg (net/socket.c:2738)
? __pfx____sys_sendmsg (net/socket.c:2625)
? perf_event_task_tick (./include/linux/rcupdate.h:838)
? sched_tick (kernel/sched/core.c:5818)
? clockevents_program_event (kernel/time/clockevents.c:372)
? fdget (./include/linux/rcupdate.h:873 fs/file.c:1100)
__sys_sendmsg (net/socket.c:2770)
? __pfx___sys_sendmsg (net/socket.c:2751)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
</TASK>
Fix by publishing only once the object is fully initialised:
__mctp_dev_get() runs under rcu_read_lock() only and hands
this object to readers as soon as mctp_ptr is assigned, so
they must never observe mdev->dev == NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_api: reclaim an empty proto on the error path
Two racing tc filter add requests on the same chain/prio of an
unlocked classifier both run change() on the shared proto and both
can fail: the winner's tcf_chain_tp_delete_empty() attempt gives up
because the loser's handle is still in the idr, and the loser's
error path drops only its own reference without a second reclamation
attempt. The empty proto stays linked in the chain, holding the
chain reference, a block reference and the classifier module
reference until the chain or block is torn down.
Reclaim the proto on the error path of any failed request that holds
a proto reference. The reclamation is emptiness-gated:
tcf_chain_tp_delete_empty() unlinks the proto only when
delete_empty() admits it is empty, so a live shared proto is never
unlinked. A proto the request created is reclaimed unconditionally -
it is the only owner, so marking it for deletion is safe even without
a delete_empty callback. Classifiers without one (the check marks the
proto unconditionally) are rtnl-serialized, so the raced window this
guard closes cannot arise for them.
This is a follow-up to commit d4e359b3608a ("net/sched: cls_api: fix
teardown of an adopted proto on insert-race loss"), which stopped the
loser of the insert race from unlinking the winner's live proto but
left the empty-proto residual in place.
Conditions to recreate:
- CONFIG_NET_CLS_FLOWER=y; veth pair
- tc qdisc add dev veth0 ingress
- two concurrent `tc filter add dev veth0 ingress protocol ip pref 1
flower skip_sw ... action drop` (both fail in fl_hw_replace_filter
after publishing their handle in the idr); repeat in a loop
- an empty flower tp stays linked after both requests fail; visible
as a bare `filter protocol ip pref 1 flower chain 0` header in
`tc filter show` with no filter entries
- CAP_NET_ADMIN (namespace-local via unshare -Urn suffices) |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: don't drain cmd_sync backlog on unregister
hci_unregister_dev() disables cmd_work and cmd_timer, then calls
hci_cmd_sync_clear(), whose cancel_work_sync() waits for
hci_cmd_sync_work() to return. That worker dequeues and runs every
entry on cmd_sync_work_list. With cmd_work disabled nothing reaches
the controller, so each queued HCI command waits the full
HCI_CMD_TIMEOUT (2s).
The backlog has no bound. Userspace can keep queuing MGMT commands
such as MGMT_OP_GET_CLOCK_INFO against a controller that doesn't
answer. Closing /dev/vhci then blocks in vhci_release() for
backlog * 2s:
INFO: task syz-executor:5749 blocked for more than 143 seconds.
cancel_work_sync
hci_cmd_sync_clear
hci_unregister_dev
vhci_release
In a local reproduction the backlog held more than 5000 entries,
which comes to hours of hang.
Stop the worker from taking new entries once HCI_UNREGISTER is set,
and wake any request still waiting with -ENODEV before cancelling
the work. The entries left over are destroyed with -ECANCELED by the
existing sweep in hci_cmd_sync_clear(). They stay on the list until
the work has stopped, so hci_cmd_sync_dequeue() and friends still see
them. A callback already running may still issue another command,
which delays unregister by at most one timeout per remaining command,
not by the whole backlog. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: prevent GCM nonce reuse on peer key changes
TIPC can encrypt traffic between nodes using a different transmit key
for each node. In this mode, the AES-GCM nonce for a packet sent to a
known peer consists of a 32-bit prefix (a per-key salt XOR the peer's
address) followed by a 64-bit counter. That counter is stored in the
peer's RX crypto object. When the peer reports a change in which key
it uses to receive packets, TIPC resets this counter. The sender can
still be using the same TX key and salt, so subsequent packets reuse
earlier nonces. This nonce reuse breaks confidentiality and exposes
GCM's authentication key. This makes forgeries trivial: an attacker
can exploit CTR malleability to alter captured ciphertexts and use the
recovered authentication key to compute a valid tag for the modified
ciphertext, under the same key and nonce.
Use the TX key's existing aead->seqno counter instead. All encryptions
using that key object share the same atomic counter, so concurrent
encryptions get distinct nonce counter values. The counter survives
key activation and peer reconnection, and peer key-status reports
cannot reset it. This prevents those transitions from causing nonce
reuse while the same TX key remains installed.
The nonce format is unchanged, and receivers do not require consecutive
counter values, so sharing the counter across peers remains compatible
with existing receivers. A pre-existing check still invokes key
revocation in the unlikely event that the counter wraps to zero. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: fix NULL dereference in set_coalesce before first open
The Rx ring priv and index are only set in bcmgenet_init_rx_ring(),
which runs at open. Setting the Rx coalescing parameters on an interface
that was never opened, e.g. "ethtool -C eth0 rx-usecs 50", dereferences
a NULL ring->priv. The oops happens with RTNL held, so networking
stays stuck until a reboot:
Unable to handle kernel paging request at virtual address 0000000000002788
pc : bcmgenet_set_rx_coalesce.isra.0+0x10/0x88
lr : bcmgenet_set_coalesce+0xe8/0x180
Call trace:
bcmgenet_set_rx_coalesce.isra.0+0x10/0x88 (P)
__ethnl_set_coalesce.isra.0+0x490/0x570
ethnl_set_coalesce+0x48/0xc0
ethnl_default_set_doit+0xf4/0x230
genl_family_rcv_msg_doit+0xe8/0x160
genl_rcv_msg+0x220/0x2a0
netlink_rcv_skb+0x68/0x140
genl_rcv+0x40/0x60
netlink_unicast+0x338/0x3c0
netlink_sendmsg+0x19c/0x3f8
__sock_sendmsg+0x64/0xc0
__sys_sendto+0x124/0x198
__arm64_sys_sendto+0x30/0x48
Set priv and index at probe. Writing the registers while the interface
is down is harmless because open resets the MAC and
bcmgenet_init_rx_coalesce() reapplies the stored values.
It was observed on a Raspberry Pi CM4, but should apply to all other
genet devices. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: filter some flags received in the backup server
While the IPVS SYNC protocol is not secure by design
we can still protect the backup server from messages that
can wreak havoc.
This commit addresses problems from received connection flags
or their combinations. We now drop messages as follows:
1. the NO_CPORT+TEMPLATE combination allows lookups for normal
connections to hit template which can break in many ways.
While the master does not sync connections with NO_CPORT flag,
i.e. before they are established, we still accept NO_CPORT
without TEMPLATE.
2. ONE_PACKET: it is not sent by master, so we do not
expect it in backup. Before now it was ignored by
IP_VS_CONN_F_BACKUP_MASK for protocol v1 while protocol
v0 created connections that are not hashed and dropped
immediately. Better to apply the IP_VS_CONN_F_BACKUP_MASK
also to the flags from v0 messages for consistency with v1. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: bpf: reject invalid NAT manipulation types
As bpf_ct_set_nat_info() is not validating the NAT manipulation type a
wrong value can be passed directly to nf_nat_setup_info(). This triggers
the WARN_ON() at nf_nat_setup_info() and if panic_on_warn isn't set,
then IPS_SRC_NAT_DONE is set without adding nat_bysource and conntrack
cleanup tries to unlink an uninitialized hlist node.
Fix this by checking that NAT manipulation type is correct before
calling nf_nat_setup_info(). In addition, if the WARN_ON is hit, return
NF_DROP instead of continuing with the processing to avoid similar
situations in the future. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix race between perf_event_exit_task() and perf_pending_task()
A race condition exists between perf_event_exit_task() and
perf_pending_task() during begin_new_exec().
During begin_new_exec(), perf_event_exit_task() may be called, and the
PF_EXITING flag is not set on task. So perf_sigtrap() continues to execute
and triggers WARN_ON_ONCE(event->ctx->task != current).
Since both task exit and exec paths can call perf_event_exit_task() which
sets ctx->task to TASK_TOMBSTONE, fix this by explicitly checking if
event->ctx->task equals TASK_TOMBSTONE and dropping the redundant
PF_EXITING check. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: check dc_state_create_copy() for NULL in dm_suspend
dc_state_create_copy() can return NULL on allocation failure.
dm_suspend() only conditionally skips dm_gpureset_toggle_interrupts()
and continues execution, returning success. dm_resume() then
dereferences the NULL cached_dc_state in link_enc_cfg_copy() and the
following dc_state->stream_count loop, crashing during GPU reset
recovery.
Return -ENOMEM immediately if the copy fails, so the caller aborts
suspend instead of leaving a NULL cached state for resume.
(cherry picked from commit 84b6d7932fdd2857795a257f9f258562a3cddcab) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx6: fix firmware leak on teardown
The firmware requested in gfx_v6_0_init_microcode() is not released
when the GFX block is torn down, leaking the firmware resources.
Add gfx_v6_0_free_microcode() and call it from gfx_v6_0_sw_fini()
to release the PFP, ME, CE and RLC firmware.
(cherry picked from commit 386e81346f95ab0be5a82c5535de932e7a456924) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix IP instance memory leak on kobject add failure
amdgpu_discovery_sysfs_ips() allocates ip_hw_instance with
kzalloc_flex() and initializes its embedded kobject before calling
kobject_add().
If kobject_add() fails, the return value is ignored and execution
continues without dropping the initial kobject reference. The failed
kobject is not retained in the kset list, so the normal sysfs teardown
path cannot find it. As a result, ip_hw_instance_release() is never
called and the ip_hw_instance allocation is leaked.
Call kobject_put() when kobject_add() fails so the initial reference is
dropped and ip_hw_instance_release() can free the allocation. Keep the
existing best-effort sysfs behavior by continuing with the remaining IP
entries after the failed registration.
The issue was identified by a static analysis tool I developed and
confirmed by manual review.
(cherry picked from commit 5c75fbcca8af1096d8d9415b91d8ea6212c22ee1) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix ACP MFD device leak on init failure
acp_hw_init() registers ACP child devices with mfd_add_devices() before
attaching them to the ACP power domain and initializing the hardware.
If attaching a child to the power domain fails, or if the ACP reset or
clock enable operation times out, the failure path frees only the
source cell, resource, and platform-data allocations. The child
platform devices already registered by mfd_add_devices() remain
registered and are never released.
Remove the children from the power domain and unregister the MFD
devices on failures that occur after mfd_add_devices() succeeds. Keep
mfd_add_devices() failures on the existing cleanup path since the MFD
core already rolls back partially registered children itself.
The issue was identified by a static analysis tool I developed and
confirmed by manual review.
(cherry picked from commit 63da68d6a2279ec945581c990c5a59a5ae8b5560) |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix is_failure flag for superseded transaction cleanup
When a TF_UPDATE_TXN transaction supersedes a pending async transaction,
binder_release_entire_buffer() is called with is_failure=false. Since the
superseded transaction was never delivered, binder_apply_fd_fixups() was
never called and no fds were installed in the target process.
With is_failure=false, the BINDER_TYPE_FDA cleanup handler interprets
stale buffer contents as installed fd numbers and passes them to
binder_deferred_fd_close(), closing unrelated file descriptors.
Pass is_failure=true since the transaction was never delivered to the
target, matching the semantics of all other undelivered-transaction
cleanup paths. |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix leaked fd fixups on TF_UPDATE_TXN supersede
When a TF_UPDATE_TXN transaction supersedes a pending async transaction
in a frozen process, the outdated transaction is freed with kfree()
directly. This skips binder_free_txn_fixups(), leaking all
binder_txn_fd_fixup entries and their fget()'d struct file references.
The leaked file refcounts never reach zero, so the struct file objects
are permanently pinned in memory. They survive process exit and
accumulate across invocations until file-max exhaustion.
Every other transaction cleanup path (binder_free_transaction(),
binder_transaction() error paths, binder_release_work()) correctly
calls binder_free_txn_fixups(). Add the missing call before kfree()
in the t_outdated cleanup block. |
| In the Linux kernel, the following vulnerability has been resolved:
nitro_enclaves: fix use-after-free on SLOT_ALLOC failure
When ne_create_vm_ioctl() fails the SLOT_ALLOC request after
anon_inode_getfile() has succeeded, the error path calls
fput(enclave_file) and then frees ne_enclave.
In normal userspace context, fput() defers the final __fput() via
task_work. ne_enclave_release() therefore runs after ne_enclave has
already been freed and dereferences ne_enclave->slot_uid, causing a
use-after-free: KASAN: slab-use-after-free in ne_enclave_release.
The enclave has no slot allocated and is not yet linked into the
enclaves list on this error path, so ne_enclave_release() is expected
to return early when slot_uid is zero. However, reading slot_uid
already accesses the freed object.
Clear enclave_file->private_data before fput() on the error path.
ne_enclave_release() then returns immediately when private_data is
NULL, leaving the ioctl error path as the sole owner of ne_enclave.
This is safe because the file has not been fd_install()'d yet.
Tested on an AWS EC2 m5.2xlarge with CONFIG_KASAN=y. Without the
patch, the reproducer triggers a KASAN slab-use-after-free on every
SLOT_ALLOC failure. With the patch, no KASAN report is produced and
the SLOT_ALLOC error is still returned. Normal enclave creation and
teardown are unaffected. |
