| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs: check contexts->nr before accessing contexts_arr[0]
Multiple sysfs command paths dereference contexts_arr[0] without first
verifying that kdamond->contexts->nr == 1. A user can set nr_contexts to
0 via sysfs while DAMON is running, causing NULL pointer dereferences.
In more detail, the issue can be triggered by privileged users like
below.
First, start DAMON and make contexts directory empty
(kdamond->contexts->nr == 0).
# damo start
# cd /sys/kernel/mm/damon/admin/kdamonds/0
# echo 0 > contexts/nr_contexts
Then, each of below commands will cause the NULL pointer dereference.
# echo update_schemes_stats > state
# echo update_schemes_tried_regions > state
# echo update_schemes_tried_bytes > state
# echo update_schemes_effective_quotas > state
# echo update_tuned_intervals > state
Guard all commands (except OFF) at the entry point of
damon_sysfs_handle_cmd(). |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: fix invalid folio access when i_blkbits differs from I/O granularity
Commit aa35dd5cbc06 ("iomap: fix invalid folio access after
folio_end_read()") partially addressed invalid folio access for folios
without an ifs attached, but it did not handle the case where
1 << inode->i_blkbits matches the folio size but is different from the
granularity used for the IO, which means IO can be submitted for less
than the full folio for the !ifs case.
In this case, the condition:
if (*bytes_submitted == folio_len)
ctx->cur_folio = NULL;
in iomap_read_folio_iter() will not invalidate ctx->cur_folio, and
iomap_read_end() will still be called on the folio even though the IO
helper owns it and will finish the read on it.
Fix this by unconditionally invalidating ctx->cur_folio for the !ifs
case. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ibmvfc: Fix OOB access in ibmvfc_discover_targets_done()
A malicious or compromised VIO server can return a num_written value in the
discover targets MAD response that exceeds max_targets. This value is
stored directly in vhost->num_targets without validation, and is then used
as the loop bound in ibmvfc_alloc_targets() to index into disc_buf[], which
is only allocated for max_targets entries. Indices at or beyond max_targets
access kernel memory outside the DMA-coherent allocation. The
out-of-bounds data is subsequently embedded in Implicit Logout and PLOGI
MADs that are sent back to the VIO server, leaking kernel memory.
Fix by clamping num_written to max_targets before storing it. |
| In the Linux kernel, the following vulnerability has been resolved:
virt: tdx-guest: Fix handling of host controlled 'quote' buffer length
Validate host controlled value `quote_buf->out_len` that determines how
many bytes of the quote are copied out to guest userspace. In TDX
environments with remote attestation, quotes are not considered private,
and can be forwarded to an attestation server.
Catch scenarios where the host specifies a response length larger than
the guest's allocation, or otherwise races modifying the response while
the guest consumes it.
This prevents contents beyond the pages allocated for `quote_buf`
(up to TSM_REPORT_OUTBLOB_MAX) from being read out to guest userspace,
and possibly forwarded in attestation requests.
Recall that some deployments want per-container configs-tsm-report
interfaces, so the leak may cross container protection boundaries, not
just local root. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: iptfs: only publish mode_data after clone setup
iptfs_clone_state() stores x->mode_data before allocating the reorder
window. If that allocation fails, the code frees the cloned state and
returns -ENOMEM, leaving x->mode_data pointing at freed memory.
The xfrm clone unwind later runs destroy_state() through x->mode_data,
so the failed clone path tears down IPTFS state that clone_state()
already freed.
Keep the cloned IPTFS state private until all allocations succeed so
failed clones leave x->mode_data unset. The destroy path already
handles a NULL mode_data pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: iptfs: validate inner IPv4 header length in IPTFS payload
Add validation of the inner IPv4 packet tot_len and ihl fields parsed
from decrypted IPTFS payloads in __input_process_payload(). A crafted
ESP packet containing an inner IPv4 header with tot_len=0 causes an
infinite loop: iplen=0 leads to capturelen=min(0, remaining)=0, so the
data offset never advances and the while(data < tail) loop never
terminates, spinning forever in softirq context.
Reject inner IPv4 packets where tot_len < ihl*4 or ihl*4 < sizeof(struct
iphdr), which catches both the tot_len=0 case and malformed ihl values.
The normal IP stack performs this validation in ip_rcv_core(), but IPTFS
extracts and processes inner packets before they reach that layer. |
| In the Linux kernel, the following vulnerability has been resolved:
media: mc, v4l2: serialize REINIT and REQBUFS with req_queue_mutex
MEDIA_REQUEST_IOC_REINIT can run concurrently with VIDIOC_REQBUFS(0)
queue teardown paths. This can race request object cleanup against vb2
queue cancellation and lead to use-after-free reports.
We already serialize request queueing against STREAMON/OFF with
req_queue_mutex. Extend that serialization to REQBUFS, and also take
the same mutex in media_request_ioctl_reinit() so REINIT is in the
same exclusion domain.
This keeps request cleanup and queue cancellation from running in
parallel for request-capable devices. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: sma1307: fix double free of devm_kzalloc() memory
A previous change added NULL checks and cleanup for allocation
failures in sma1307_setting_loaded().
However, the cleanup for mode_set entries is wrong. Those entries are
allocated with devm_kzalloc(), so they are device-managed resources and
must not be freed with kfree(). Manually freeing them in the error path
can lead to a double free when devres later releases the same memory.
Drop the manual kfree() loop and let devres handle the cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix memory leaks and NULL deref in smb2_lock()
smb2_lock() has three error handling issues after list_del() detaches
smb_lock from lock_list at no_check_cl:
1) If vfs_lock_file() returns an unexpected error in the non-UNLOCK
path, goto out leaks smb_lock and its flock because the out:
handler only iterates lock_list and rollback_list, neither of
which contains the detached smb_lock.
2) If vfs_lock_file() returns -ENOENT in the UNLOCK path, goto out
leaks smb_lock and flock for the same reason. The error code
returned to the dispatcher is also stale.
3) In the rollback path, smb_flock_init() can return NULL on
allocation failure. The result is dereferenced unconditionally,
causing a kernel NULL pointer dereference. Add a NULL check to
prevent the crash and clean up the bookkeeping; the VFS lock
itself cannot be rolled back without the allocation and will be
released at file or connection teardown.
Fix cases 1 and 2 by hoisting the locks_free_lock()/kfree() to before
the if(!rc) check in the UNLOCK branch so all exit paths share one
free site, and by freeing smb_lock and flock before goto out in the
non-UNLOCK branch. Propagate the correct error code in both cases.
Fix case 3 by wrapping the VFS unlock in an if(rlock) guard and adding
a NULL check for locks_free_lock(rlock) in the shared cleanup.
Found via call-graph analysis using sqry. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: replace hardcoded hdr2_len with offsetof() in smb2_calc_max_out_buf_len()
After this commit (e2b76ab8b5c9 "ksmbd: add support for read compound"),
response buffer management was changed to use dynamic iov array.
In the new design, smb2_calc_max_out_buf_len() expects the second
argument (hdr2_len) to be the offset of ->Buffer field in the
response structure, not a hardcoded magic number.
Fix the remaining call sites to use the correct offsetof() value. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix potential deadlock in cpu hotplug with osnoise
The following sequence may leads deadlock in cpu hotplug:
task1 task2 task3
----- ----- -----
mutex_lock(&interface_lock)
[CPU GOING OFFLINE]
cpus_write_lock();
osnoise_cpu_die();
kthread_stop(task3);
wait_for_completion();
osnoise_sleep();
mutex_lock(&interface_lock);
cpus_read_lock();
[DEAD LOCK]
Fix by swap the order of cpus_read_lock() and mutex_lock(&interface_lock). |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Drain deferred trigger frees if kthread creation fails
Boot-time trigger registration can fail before the trigger-data cleanup
kthread exists. Deferring those frees until late init is fine, but the
post-boot fallback must still drain the deferred list if kthread
creation never succeeds.
Otherwise, boot-deferred nodes can accumulate on
trigger_data_free_list, later frees fall back to synchronously freeing
only the current object, and the older queued entries are leaked
forever.
To trigger this, add the following to the kernel command line:
trace_event=sched_switch trace_trigger=sched_switch.traceon,sched_switch.traceon
The second traceon trigger will fail and be freed. This triggers a NULL
pointer dereference and crashes the kernel.
Keep the deferred boot-time behavior, but when kthread creation fails,
drain the whole queued list synchronously. Do the same in the late-init
drain path so queued entries are not stranded there either. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/entry: Scrub r12 register on kernel entry
Before commit f33f2d4c7c80 ("s390/bp: remove TIF_ISOLATE_BP"),
all entry handlers loaded r12 with the current task pointer
(lg %r12,__LC_CURRENT) for use by the BPENTER/BPEXIT macros. That
commit removed TIF_ISOLATE_BP, dropping both the branch prediction
macros and the r12 load, but did not add r12 to the register clearing
sequence.
Add the missing xgr %r12,%r12 to make the register scrub consistent
across all entry points. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/syscalls: Add spectre boundary for syscall dispatch table
The s390 syscall number is directly controlled by userspace, but does
not have an array_index_nospec() boundary to prevent access past the
syscall function pointer tables. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/fdinfo: fix OOB read in SQE_MIXED wrap check
__io_uring_show_fdinfo() iterates over pending SQEs and, for 128-byte
SQEs on an IORING_SETUP_SQE_MIXED ring, needs to detect when the second
half of the SQE would be past the end of the sq_sqes array. The current
check tests (++sq_head & sq_mask) == 0, but sq_head is only incremented
when a 128-byte SQE is encountered, not on every iteration. The actual
array index is sq_idx = (i + sq_head) & sq_mask, which can be sq_mask
(the last slot) while the wrap check passes.
Fix by checking sq_idx directly. Keep the sq_head increment so the loop
still skips the second half of the 128-byte SQE on the next iteration. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-fsl-lpspi: fix teardown order issue (UAF)
There is a teardown order issue in the driver. The SPI controller is
registered using devm_spi_register_controller(), which delays
unregistration of the SPI controller until after the fsl_lpspi_remove()
function returns.
As the fsl_lpspi_remove() function synchronously tears down the DMA
channels, a running SPI transfer triggers the following NULL pointer
dereference due to use after free:
| fsl_lpspi 42550000.spi: I/O Error in DMA RX
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[...]
| Call trace:
| fsl_lpspi_dma_transfer+0x260/0x340 [spi_fsl_lpspi]
| fsl_lpspi_transfer_one+0x198/0x448 [spi_fsl_lpspi]
| spi_transfer_one_message+0x49c/0x7c8
| __spi_pump_transfer_message+0x120/0x420
| __spi_sync+0x2c4/0x520
| spi_sync+0x34/0x60
| spidev_message+0x20c/0x378 [spidev]
| spidev_ioctl+0x398/0x750 [spidev]
[...]
Switch from devm_spi_register_controller() to spi_register_controller() in
fsl_lpspi_probe() and add the corresponding spi_unregister_controller() in
fsl_lpspi_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/core) Protect regulator operations with mutex
The regulator operations pmbus_regulator_get_voltage(),
pmbus_regulator_set_voltage(), and pmbus_regulator_list_voltage()
access PMBus registers and shared data but were not protected by
the update_lock mutex. This could lead to race conditions.
However, adding mutex protection directly to these functions causes
a deadlock because pmbus_regulator_notify() (which calls
regulator_notifier_call_chain()) is often called with the mutex
already held (e.g., from pmbus_fault_handler()). If a regulator
callback then calls one of the now-protected voltage functions,
it will attempt to acquire the same mutex.
Rework pmbus_regulator_notify() to utilize a worker function to
send notifications outside of the mutex protection. Events are
stored as atomics in a per-page bitmask and processed by the worker.
Initialize the worker and its associated data during regulator
registration, and ensure it is cancelled on device removal using
devm_add_action_or_reset().
While at it, remove the unnecessary include of linux/of.h. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: use generic driver_override infrastructure
When a driver is probed through __driver_attach(), the bus' match()
callback is called without the device lock held, thus accessing the
driver_override field without a lock, which can cause a UAF.
Fix this by using the driver-core driver_override infrastructure taking
care of proper locking internally.
Note that calling match() from __driver_attach() without the device lock
held is intentional. [1]
Also note that we do not enable the driver_override feature of struct
bus_type, as SPI - in contrast to most other buses - passes "" to
sysfs_emit() when the driver_override pointer is NULL. Thus, printing
"\n" instead of "(null)\n". |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/pf: Fix use-after-free in migration restore
When an error is returned from xe_sriov_pf_migration_restore_produce(),
the data pointer is not set to NULL, which can trigger use-after-free
in subsequent .write() calls.
Set the pointer to NULL upon error to fix the problem.
(cherry picked from commit 4f53d8c6d23527d734fe3531d08e15cb170a0819) |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Harden depth calculation functions
An issue was exposed where OS can pass in U32_MAX for SQ/RQ/SRQ size.
This can cause integer overflow and truncation of SQ/RQ/SRQ depth
returning a success when it should have failed.
Harden the functions to do all depth calculations and boundary
checking in u64 sizes. |
