| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
smb: Log an error when close_all_cached_dirs fails
Under low-memory conditions, close_all_cached_dirs() can't move the
dentries to a separate list to dput() them once the locks are dropped.
This will result in a "Dentry still in use" error, so add an error
message that makes it clear this is what happened:
[ 495.281119] CIFS: VFS: \\otters.example.com\share Out of memory while dropping dentries
[ 495.281595] ------------[ cut here ]------------
[ 495.281887] BUG: Dentry ffff888115531138{i=78,n=/} still in use (2) [unmount of cifs cifs]
[ 495.282391] WARNING: CPU: 1 PID: 2329 at fs/dcache.c:1536 umount_check+0xc8/0xf0
Also, bail out of looping through all tcons as soon as a single
allocation fails, since we're already in trouble, and kmalloc() attempts
for subseqeuent tcons are likely to fail just like the first one did. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: exit after state insertion failure at btrfs_convert_extent_bit()
If insert_state() state failed it returns an error pointer and we call
extent_io_tree_panic() which will trigger a BUG() call. However if
CONFIG_BUG is disabled, which is an uncommon and exotic scenario, then
we fallthrough and call cache_state() which will dereference the error
pointer, resulting in an invalid memory access.
So jump to the 'out' label after calling extent_io_tree_panic(), it also
makes the code more clear besides dealing with the exotic scenario where
CONFIG_BUG is disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: add NULL check in automount_fullpath
page is checked for null in __build_path_from_dentry_optional_prefix
when tcon->origin_fullpath is not set. However, the check is missing when
it is set.
Add a check to prevent a potential NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: fix array-index-out-of-bounds read in add_missing_indices
stbl is s8 but it must contain offsets into slot which can go from 0 to
127.
Added a bound check for that error and return -EIO if the check fails.
Also make jfs_readdir return with error if add_missing_indices returns
with an error. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Disable SCO support if READ_VOICE_SETTING is unsupported/broken
A SCO connection without the proper voice_setting can cause
the controller to lock up. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: don't warn when if there is a FW error
iwl_trans_reclaim is warning if it is called when the FW is not alive.
But if it is called when there is a pending restart, i.e. after a FW
error, there is no need to warn, instead - return silently. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Fix race of buffer access at PCM OSS layer
The PCM OSS layer tries to clear the buffer with the silence data at
initialization (or reconfiguration) of a stream with the explicit call
of snd_pcm_format_set_silence() with runtime->dma_area. But this may
lead to a UAF because the accessed runtime->dma_area might be freed
concurrently, as it's performed outside the PCM ops.
For avoiding it, move the code into the PCM core and perform it inside
the buffer access lock, so that it won't be changed during the
operation. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost-scsi: protect vq->log_used with vq->mutex
The vhost-scsi completion path may access vq->log_base when vq->log_used is
already set to false.
vhost-thread QEMU-thread
vhost_scsi_complete_cmd_work()
-> vhost_add_used()
-> vhost_add_used_n()
if (unlikely(vq->log_used))
QEMU disables vq->log_used
via VHOST_SET_VRING_ADDR.
mutex_lock(&vq->mutex);
vq->log_used = false now!
mutex_unlock(&vq->mutex);
QEMU gfree(vq->log_base)
log_used()
-> log_write(vq->log_base)
Assuming the VMM is QEMU. The vq->log_base is from QEMU userpace and can be
reclaimed via gfree(). As a result, this causes invalid memory writes to
QEMU userspace.
The control queue path has the same issue. |
| In the Linux kernel, the following vulnerability has been resolved:
libnvdimm/labels: Fix divide error in nd_label_data_init()
If a faulty CXL memory device returns a broken zero LSA size in its
memory device information (Identify Memory Device (Opcode 4000h), CXL
spec. 3.1, 8.2.9.9.1.1), a divide error occurs in the libnvdimm
driver:
Oops: divide error: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:nd_label_data_init+0x10e/0x800 [libnvdimm]
Code and flow:
1) CXL Command 4000h returns LSA size = 0
2) config_size is assigned to zero LSA size (CXL pmem driver):
drivers/cxl/pmem.c: .config_size = mds->lsa_size,
3) max_xfer is set to zero (nvdimm driver):
drivers/nvdimm/label.c: max_xfer = min_t(size_t, ndd->nsarea.max_xfer, config_size);
4) A subsequent DIV_ROUND_UP() causes a division by zero:
drivers/nvdimm/label.c: /* Make our initial read size a multiple of max_xfer size */
drivers/nvdimm/label.c: read_size = min(DIV_ROUND_UP(read_size, max_xfer) * max_xfer,
drivers/nvdimm/label.c- config_size);
Fix this by checking the config size parameter by extending an
existing check. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-epf-test: Fix double free that causes kernel to oops
Fix a kernel oops found while testing the stm32_pcie Endpoint driver
with handling of PERST# deassertion:
During EP initialization, pci_epf_test_alloc_space() allocates all BARs,
which are further freed if epc_set_bar() fails (for instance, due to no
free inbound window).
However, when pci_epc_set_bar() fails, the error path:
pci_epc_set_bar() ->
pci_epf_free_space()
does not clear the previous assignment to epf_test->reg[bar].
Then, if the host reboots, the PERST# deassertion restarts the BAR
allocation sequence with the same allocation failure (no free inbound
window), creating a double free situation since epf_test->reg[bar] was
deallocated and is still non-NULL.
Thus, make sure that pci_epf_alloc_space() and pci_epf_free_space()
invocations are symmetric, and as such, set epf_test->reg[bar] to NULL
when memory is freed.
[kwilczynski: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: lzo - Fix compression buffer overrun
Unlike the decompression code, the compression code in LZO never
checked for output overruns. It instead assumes that the caller
always provides enough buffer space, disregarding the buffer length
provided by the caller.
Add a safe compression interface that checks for the end of buffer
before each write. Use the safe interface in crypto/lzo. |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache: prevent BUG_ON by blocking retries on failed device resumes
A cache device failing to resume due to mapping errors should not be
retried, as the failure leaves a partially initialized policy object.
Repeating the resume operation risks triggering BUG_ON when reloading
cache mappings into the incomplete policy object.
Reproduce steps:
1. create a cache metadata consisting of 512 or more cache blocks,
with some mappings stored in the first array block of the mapping
array. Here we use cache_restore v1.0 to build the metadata.
cat <<EOF >> cmeta.xml
<superblock uuid="" block_size="128" nr_cache_blocks="512" \
policy="smq" hint_width="4">
<mappings>
<mapping cache_block="0" origin_block="0" dirty="false"/>
</mappings>
</superblock>
EOF
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
cache_restore -i cmeta.xml -o /dev/mapper/cmeta --metadata-version=2
dmsetup remove cmeta
2. wipe the second array block of the mapping array to simulate
data degradations.
mapping_root=$(dd if=/dev/sdc bs=1c count=8 skip=192 \
2>/dev/null | hexdump -e '1/8 "%u\n"')
ablock=$(dd if=/dev/sdc bs=1c count=8 skip=$((4096*mapping_root+2056)) \
2>/dev/null | hexdump -e '1/8 "%u\n"')
dd if=/dev/zero of=/dev/sdc bs=4k count=1 seek=$ablock
3. try bringing up the cache device. The resume is expected to fail
due to the broken array block.
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
dmsetup create cdata --table "0 65536 linear /dev/sdc 8192"
dmsetup create corig --table "0 524288 linear /dev/sdc 262144"
dmsetup create cache --notable
dmsetup load cache --table "0 524288 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
dmsetup resume cache
4. try resuming the cache again. An unexpected BUG_ON is triggered
while loading cache mappings.
dmsetup resume cache
Kernel logs:
(snip)
------------[ cut here ]------------
kernel BUG at drivers/md/dm-cache-policy-smq.c:752!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 332 Comm: dmsetup Not tainted 6.13.4 #3
RIP: 0010:smq_load_mapping+0x3e5/0x570
Fix by disallowing resume operations for devices that failed the
initial attempt. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio: break and reset virtio devices on device_shutdown()
Hongyu reported a hang on kexec in a VM. QEMU reported invalid memory
accesses during the hang.
Invalid read at addr 0x102877002, size 2, region '(null)', reason: rejected
Invalid write at addr 0x102877A44, size 2, region '(null)', reason: rejected
...
It was traced down to virtio-console. Kexec works fine if virtio-console
is not in use.
The issue is that virtio-console continues to write to the MMIO even after
underlying virtio-pci device is reset.
Additionally, Eric noticed that IOMMUs are reset before devices, if
devices are not reset on shutdown they continue to poke at guest memory
and get errors from the IOMMU. Some devices get wedged then.
The problem can be solved by breaking all virtio devices on virtio
bus shutdown, then resetting them. |
| In the Linux kernel, the following vulnerability has been resolved:
net: pktgen: fix access outside of user given buffer in pktgen_thread_write()
Honour the user given buffer size for the strn_len() calls (otherwise
strn_len() will access memory outside of the user given buffer). |
| In the Linux kernel, the following vulnerability has been resolved:
virtio_ring: Fix data race by tagging event_triggered as racy for KCSAN
syzbot reports a data-race when accessing the event_triggered, here is the
simplified stack when the issue occurred:
==================================================================
BUG: KCSAN: data-race in virtqueue_disable_cb / virtqueue_enable_cb_delayed
write to 0xffff8881025bc452 of 1 bytes by task 3288 on cpu 0:
virtqueue_enable_cb_delayed+0x42/0x3c0 drivers/virtio/virtio_ring.c:2653
start_xmit+0x230/0x1310 drivers/net/virtio_net.c:3264
__netdev_start_xmit include/linux/netdevice.h:5151 [inline]
netdev_start_xmit include/linux/netdevice.h:5160 [inline]
xmit_one net/core/dev.c:3800 [inline]
read to 0xffff8881025bc452 of 1 bytes by interrupt on cpu 1:
virtqueue_disable_cb_split drivers/virtio/virtio_ring.c:880 [inline]
virtqueue_disable_cb+0x92/0x180 drivers/virtio/virtio_ring.c:2566
skb_xmit_done+0x5f/0x140 drivers/net/virtio_net.c:777
vring_interrupt+0x161/0x190 drivers/virtio/virtio_ring.c:2715
__handle_irq_event_percpu+0x95/0x490 kernel/irq/handle.c:158
handle_irq_event_percpu kernel/irq/handle.c:193 [inline]
value changed: 0x01 -> 0x00
==================================================================
When the data race occurs, the function virtqueue_enable_cb_delayed() sets
event_triggered to false, and virtqueue_disable_cb_split/packed() reads it
as false due to the race condition. Since event_triggered is an unreliable
hint used for optimization, this should only cause the driver temporarily
suggest that the device not send an interrupt notification when the event
index is used.
Fix this KCSAN reported data-race issue by explicitly tagging the access as
data_racy. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: fix debug actions order
The order of actions taken for debug was implemented incorrectly.
Now we implemented the dump split and do the FW reset only in the
middle of the dump (rather than the FW killing itself on error.)
As a result, some of the actions taken when applying the config
will now crash the device, so we need to fix the order. |
| In the Linux kernel, the following vulnerability has been resolved:
media: cx231xx: set device_caps for 417
The video_device for the MPEG encoder did not set device_caps.
Add this, otherwise the video device can't be registered (you get a
WARN_ON instead).
Not seen before since currently 417 support is disabled, but I found
this while experimenting with it. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: sunxi-ng: h616: Reparent GPU clock during frequency changes
The H616 manual does not state that the GPU PLL supports
dynamic frequency configuration, so we must take extra care when changing
the frequency. Currently any attempt to do device DVFS on the GPU lead
to panfrost various ooops, and GPU hangs.
The manual describes the algorithm for changing the PLL
frequency, which the CPU PLL notifier code already support, so we reuse
that to reparent the GPU clock to GPU1 clock during frequency
changes. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: mctrl_gpio: split disable_ms into sync and no_sync APIs
The following splat has been observed on a SAMA5D27 platform using
atmel_serial:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __might_resched+0x38c/0x598
__might_resched from disable_irq+0x1c/0x48
disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
atmel_set_termios from uart_change_line_settings+0x15c/0x994
uart_change_line_settings from uart_set_termios+0x2b0/0x668
uart_set_termios from tty_set_termios+0x600/0x8ec
tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
process_one_work from worker_thread+0x6e0/0xfb4
worker_thread from kthread+0x3d4/0x484
kthread from ret_from_fork+0x14/0x28
This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).
Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Avoid WARN_ON when configuring MQPRIO with HTB offload enabled
When attempting to enable MQPRIO while HTB offload is already
configured, the driver currently returns `-EINVAL` and triggers a
`WARN_ON`, leading to an unnecessary call trace.
Update the code to handle this case more gracefully by returning
`-EOPNOTSUPP` instead, while also providing a helpful user message. |
