| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| The Essential Grid Gallery WordPress Plugin plugin for WordPress is vulnerable to Sensitive Information Exposure in all versions up to, and including, 3.1.1 via the on_front_ajax_action() function. This makes it possible for unauthenticated attackers to view private and password protected posts that may have private or sensitive information. |
| An improper input validation the CSRF filter results in unsanitized user input written to the application logs. |
| This vulnerability allows appliance compromise at boot time. |
| An issue was discovered in Akamai Enterprise Application Access (EAA) before 2025-01-17. If an admin knows another tenant's 128-bit connector GUID, they can execute debug commands on that connector. |
| The Toolbar Extras for Elementor & More – WordPress Admin Bar Enhanced plugin for WordPress is vulnerable to Stored Cross-Site Scripting via the plugin's 'tbex-version' shortcode in all versions up to, and including, 1.4.9 due to insufficient input sanitization and output escaping on user supplied attributes. This makes it possible for authenticated attackers, with contributor-level access and above, to inject arbitrary web scripts in pages that will execute whenever a user accesses an injected page. |
| In OpenSC pam_pkcs11 before 0.6.13, pam_sm_authenticate() wrongly returns PAM_IGNORE in many error situations (such as an error triggered by a smartcard before login), allowing authentication bypass. |
| A vulnerability was found in Mercusys MW301R 1.0.2 Build 190726 Rel.59423n. It has been rated as problematic. This issue affects some unknown processing of the component Login. The manipulation leads to improper restriction of excessive authentication attempts. The attack can only be initiated within the local network. The complexity of an attack is rather high. The exploitation is known to be difficult. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way. |
| The Apptivo Business Site CRM plugin for WordPress is vulnerable to Cross-Site Request Forgery in all versions up to, and including, 5.3. This is due to missing or incorrect nonce validation on the 'awp_ip_deny' page. This makes it possible for unauthenticated attackers to block IP addresses via a forged request granted they can trick a site administrator into performing an action such as clicking on a link. |
| CKAN is an open-source DMS (data management system) for powering data hubs and data portals. Using a specially crafted file, a user could potentially upload a file containing code that when executed could send arbitrary requests to the server. If that file was opened by an administrator, it could lead to escalation of privileges of the original submitter or other malicious actions. Users must have been registered to the site to exploit this vulnerability. This vulnerability has been fixed in CKAN 2.10.7 and 2.11.2. Users are advised to upgrade. On versions prior to CKAN 2.10.7 and 2.11.2, site maintainers can restrict the file types supported for uploading using the `ckan.upload.user.mimetypes` / `ckan.upload.user.types` and `ckan.upload.group.mimetypes` / `ckan.upload.group.types` config options. To entirely disable file uploads users can use: `ckan.upload.user.types = none` |
| Unrestricted Upload of File with Dangerous Type vulnerability in Innorix Innorix WP allows Upload a Web Shell to a Web Server.This issue affects Innorix WP from All versions If the "exam" directory exists under the directory where the product is installed (ex: innorix/exam) |
| Exposure of Sensitive Information to an Unauthorized Actor, Missing Encryption of Sensitive Data, Files or Directories Accessible to External Parties vulnerability in Kings Information & Network Co. KESS Enterprise on Windows allows Privilege Escalation, Modify Existing Service, Modify Shared File.This issue affects KESS Enterprise: before *.25.9.19.exe |
| CometBFT is a distributed, Byzantine fault-tolerant, deterministic state machine replication engine. In the `blocksync` protocol peers send their `base` and `latest` heights when they connect to a new node (`A`), which is syncing to the tip of a network. `base` acts as a lower ground and informs `A` that the peer only has blocks starting from height `base`. `latest` height informs `A` about the latest block in a network. Normally, nodes would only report increasing heights. If `B` fails to provide the latest block, `B` is removed and the `latest` height (target height) is recalculated based on other nodes `latest` heights. The existing code however doesn't check for the case where `B` first reports `latest` height `X` and immediately after height `Y`, where `X > Y`. `A` will be trying to catch up to 2000 indefinitely. This condition requires the introduction of malicious code in the full node first reporting some non-existing `latest` height, then reporting lower `latest` height and nodes which are syncing using `blocksync` protocol. This issue has been patched in versions 1.0.1 and 0.38.17 and all users are advised to upgrade. Operators may attempt to ban malicious peers from the network as a workaround. |
| An authenticated user could submit scripting to fields that lack proper input and output sanitization leading to subsequent client-side script execution. |
| An administrator could discover another account's credentials. |
| An authenticated user without user-management permissions could view other users account information. |
| A suspended or recently logged-out user could continue to interact with Blueframe until the time-out period occurred. |
| An authenticated user without user administrative permissions could change the administrator Account Name. |
| Django-Unicorn adds modern reactive component functionality to Django templates. Affected versions of Django-Unicorn are vulnerable to python class pollution vulnerability. The vulnerability arises from the core functionality `set_property_value`, which can be remotely triggered by users by crafting appropriate component requests and feeding in values of second and third parameter to the vulnerable function, leading to arbitrary changes to the python runtime status. With this finding at least five ways of vulnerability exploitation have been observed, stably resulting in Cross-Site Scripting (XSS), Denial of Service (DoS), and Authentication Bypass attacks in almost every Django-Unicorn-based application. This issue has been addressed in version 0.62.0 and all users are advised to upgrade. There are no known workarounds for this vulnerability. |
| The endpoint hosts a script that allows an unauthorized remote attacker to put the system in a fail-safe state over the network due to missing authentication. |
| The HL7 FHIR IG publisher is a tool to take a set of inputs and create a standard FHIR IG. Prior to version 1.8.9, in CI contexts, the IG Publisher CLI uses git commands to determine the URL of the originating repo. If the repo was cloned, or otherwise set to use a repo that uses a username and credential based URL, the entire URL will be included in the built Implementation Guide, exposing username and credential. This does not impact users that clone public repos without credentials, such as those using the auto-ig-build continuous integration infrastructure. This problem has been patched in release 1.8.9. Some workarounds are available. Users should ensure the IG repo they are publishing does not have username or credentials included in the `origin` URL. Running the command `git remote origin url` should return a URL that contains no username, password, or token; or users should run the IG Publisher CLI with the `-repo` parameter and specify a URL that contains no username, password, or token. |
