| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: mvpp2: sync RX data at the hardware packet offset
mvpp2 programs the RX queue packet offset, so hardware writes received
data at dma_addr + MVPP2_SKB_HEADROOM. The current CPU sync starts at
dma_addr and only covers rx_bytes + MVPP2_MH_SIZE bytes, which syncs the
unused headroom and misses the same number of bytes at the packet tail.
On non-coherent DMA systems this can leave the CPU reading stale cache
contents for the end of the received frame.
Use dma_sync_single_range_for_cpu() with MVPP2_SKB_HEADROOM as the range
offset so the sync covers the Marvell header and packet data actually
written by hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mvpp2: refill RX buffers before XDP or skb use
The RX error path returns the current descriptor buffer to the hardware
BM pool. That is only valid while the driver still owns the buffer.
mvpp2_rx_refill() can fail after the current buffer has been handed to
XDP or attached to an skb. In those cases mvpp2_run_xdp() may have
recycled, redirected, or queued the page for XDP_TX, and an skb free also
retires the data buffer. Returning such a buffer to BM lets hardware DMA
into memory that is no longer owned by the RX ring.
Refill the BM pool before handing the current buffer to XDP or to the
skb. If the allocation fails there, drop the packet and return the
still-owned current buffer to BM, preserving the pool depth. Once the
refill succeeds, later local drops retire/free the current buffer instead
of returning it to BM. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: reject oversized Broadcast Announcement prepend
Existing advertising instances can already hold the maximum extended
advertising payload. When hci_adv_bcast_annoucement() prepends the
Broadcast Announcement service data to that payload, the combined data
may no longer fit in the temporary buffer used to rebuild the
advertising data.
Reject that case before copying the existing payload and report the
failure through the device log. This keeps the existing advertising
data intact and avoids overrunning the temporary buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Add bounds checks for firmware log indices
Add validation that read and write indices in the firmware log buffer
are within valid bounds (< data_size) before using them. If
out-of-bounds indices are encountered (from firmware), clamp them to
safe values instead of proceeding with invalid offsets.
This prevents potential out-of-bounds buffer access when firmware
supplies invalid log indices. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Fix signed integer truncation in IPC receive
Fix potential buffer overflow where firmware-supplied data_size is cast
to signed int before being used in min_t(). Large unsigned values
(>= 0x80000000) become negative, causing unsigned wraparound and
oversized memcpy operations that can overflow the stack buffer.
Change min_t(int, ...) to min() as both values are unsigned and can be
handled by min() without explicit cast. |
| In the Linux kernel, the following vulnerability has been resolved:
hv_netvsc: use kmap_local_page in netvsc_copy_to_send_buf
netvsc_copy_to_send_buf() copies page buffer entries into the VMBus
send buffer using phys_to_virt() on the entry PFN. Entries for the
RNDIS header and the skb linear data come from kmalloc'd memory and
are always in the kernel direct map, but entries for skb fragments
reference page cache or user pages, which on 32-bit x86 with
CONFIG_HIGHMEM=y can live above the LOWMEM boundary. For such a page
phys_to_virt() returns an address outside the direct map and the
subsequent memcpy() faults on the transmit softirq path, which is
fatal.
Map the pages with kmap_local_page() instead, handling two properties
of the page buffer entries:
- pb[i].pfn is a Hyper-V PFN at HV_HYP_PAGE_SIZE (4K) granularity,
not a native PFN. Reconstruct the physical address first and derive
the native page from it, so the mapping stays correct where
PAGE_SIZE > HV_HYP_PAGE_SIZE (e.g. arm64 with 64K pages).
- Since commit 41a6328b2c55 ("hv_netvsc: Preserve contiguous PFN
grouping in the page buffer array"), an entry describes a full
physically contiguous fragment and pb[i].len can exceed PAGE_SIZE,
while kmap_local_page() maps a single page. Copy page by page,
splitting at native page boundaries.
The copy path only handles packets smaller than the send section size
(6144 bytes by default); larger packets take the cp_partial path where
only the RNDIS header is copied. So entries here are bounded by the
section size and a copy is split at most once on 4K-page systems. On
!CONFIG_HIGHMEM configs kmap_local_page() folds to page_address() and
no mapping work is added. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: timer: Fix UAF at snd_timer_user_params()
At releasing a timer object, e.g. when a userspace timer
(CONFIG_SND_UTIMER) gets closed and snd_timer_free() is called, it
tries to detach the timer instances and release the resources.
However, it's still possible that other in-flight tasks are holding
the timer instance where the to-be-deleted timer object is associated,
and this may lead to racy accesses.
Fortunately, most of ioctls dealing with the timer instance list
already have the protection with register_mutex, and this also avoids
such races. But, SNDRV_TIMER_IOCTL_PARAMS isn't protected, hence the
concurrent ioctl may lead to use-after-free.
This patch just adds the guard with register_mutex to protect
snd_timer_user_params() for covering the code path as a quick
workaround. It's no hot-path but rather a rarely issued ioctl, so the
performance penalty doesn't matter. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/net: inherit IORING_CQE_F_BUF_MORE across bundle recv retries
When a bundle recv retries inside io_recv_finish(), the merge logic OR
the saved cflags from the previous iteration with the cflags returned by
the new iteration:
cflags = req->cqe.flags | (cflags & CQE_F_MASK);
Bits listed in CQE_F_MASK are inherited from the new iteration, and all
other bits (notably IORING_CQE_F_BUFFER and the buffer ID) come from the
saved cflags. Before this change CQE_F_MASK covered only
IORING_CQE_F_SOCK_NONEMPTY and IORING_CQE_F_MORE.
When using provided buffer rings (IOU_PBUF_RING_INC) with incremental
mode, and bundle recv, io_kbuf_inc_commit() can leave the head ring
entry partially consumed, __io_put_kbufs() then sets
IORING_CQE_F_BUF_MORE on the returned cflags so userspace knows the
buffer ID will be reused for subsequent completions.
Because IORING_CQE_F_BUF_MORE was not in CQE_F_MASK, the merge above
silently dropped it whenever the final retry iteration partially
consumed the buffer, and the subsequent req->cqe.flags = cflags &
~CQE_F_MASK save would have left a stale IORING_CQE_F_BUF_MORE in the
carried-over cflags had one been present. Userspace would then
wrongfully advance it ring head past an entry the kernel still uses.
Add IORING_CQE_F_BUF_MORE to CQE_F_MASK so it is both inherited from the
new iteration into the user-visible CQE and stripped from the saved
cflags between iterations. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: update file PMD counter before folio_put()
__split_huge_pmd_locked() updates the file/shmem RSS counter after
dropping the PMD mapping's folio reference. If folio_put() drops the last
reference, mm_counter_file() can later read freed folio state via
folio_test_swapbacked().
Move the counter update before folio_put(). |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Validate the passed in fops for ib_get_ucaps()
Sashiko pointed out it is not safe to rely only on the devt because
char/block alias so if the user finds a block device with the same dev_t
it can masquerade as a ucap cdev fd.
Test the f_ops to only accept authentic cdevs. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/srp: bound SRP_RSP sense copy by the received length
srp_process_rsp() copies sense data from rsp->data + resp_data_len,
where resp_data_len is the full 32-bit value supplied by the SRP target
and is never checked against the number of bytes actually received
(wc->byte_len). The copy length is bounded to SCSI_SENSE_BUFFERSIZE, so
at most 96 bytes are copied, but the source offset is not bounded.
A malicious or compromised SRP target on the InfiniBand/RoCE fabric that
the initiator has logged into can return an SRP_RSP with
SRP_RSP_FLAG_SNSVALID set and a large resp_data_len. The receive buffer
is allocated at the target-chosen max_ti_iu_len, so the source of the
sense copy lands past the bytes actually received; with resp_data_len
near 0xFFFFFFFF it is gigabytes past the buffer and the read faults.
Copy the sense data only if it has not been truncated, that is, only if
the response header, the response data, and the sense region fit within
the bytes actually received; otherwise drop the sense and log. The
in-tree iSER and NVMe-RDMA receive paths already bound their parse by
wc->byte_len; this brings ib_srp into line with them. |
| In the Linux kernel, the following vulnerability has been resolved:
udp: clear skb->dev before running a sockmap verdict
On the UDP receive path skb->dev is repurposed as dev_scratch (the
truesize/state cache set by udp_set_dev_scratch()), through the
union { struct net_device *dev; unsigned long dev_scratch; } in sk_buff.
When a UDP socket is in a sockmap, sk_data_ready is
sk_psock_verdict_data_ready(), which calls udp_read_skb() -> recv_actor()
(sk_psock_verdict_recv) to run the attached SK_SKB verdict program in softirq.
If that program calls a socket-lookup helper (bpf_sk_lookup_tcp/udp,
bpf_skc_lookup_tcp), bpf_skc_lookup() does:
if (skb->dev)
caller_net = dev_net(skb->dev);
skb->dev still holds the dev_scratch value (a non-NULL integer), so dev_net()
dereferences it as a struct net_device * and the kernel takes a general
protection fault on a non-canonical address in softirq:
Oops: general protection fault, probably for non-canonical address 0x1010000800004a0
CPU: 1 UID: 0 PID: 1406 Comm: syz.2.19 Not tainted 7.1.0-rc6 #1 PREEMPT(full)
RIP: 0010:bpf_skc_lookup net/core/filter.c:7033 [inline]
RIP: 0010:bpf_sk_lookup+0x45/0x160 net/core/filter.c:7047
Call Trace:
<IRQ>
bpf_prog_4675cb904b7071f8+0x12e/0x14e
bpf_prog_run_pin_on_cpu+0xc6/0x1f0
sk_psock_verdict_recv+0x1ba/0x350
udp_read_skb+0x31a/0x370
sk_psock_verdict_data_ready+0x2e3/0x600
__udp_enqueue_schedule_skb+0x4c8/0x650
udpv6_queue_rcv_one_skb+0x3ec/0x740
udp6_unicast_rcv_skb+0x11d/0x140
ip6_protocol_deliver_rcu+0x61e/0x950
ip6_input_finish+0xa9/0x150
NF_HOOK+0x286/0x2f0
ip6_input+0x117/0x220
NF_HOOK+0x286/0x2f0
__netif_receive_skb+0x85/0x200
process_backlog+0x374/0x9a0
__napi_poll+0x4f/0x1c0
net_rx_action+0x3b0/0x770
handle_softirqs+0x15a/0x460
do_softirq+0x57/0x80
</IRQ>
The rmem charge that dev_scratch accounted for is released by skb_recv_udp() on
dequeue, just above, so the scratch is dead by the time recv_actor() runs. Clear
skb->dev so bpf_skc_lookup() falls back to sock_net(skb->sk), which
skb_set_owner_sk_safe() set just above. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: allow subflow rcv wnd to shrink
In MPTCP connection, the `window` field in the TCP header refers to the
MPTCP-level rcv_nxt and it's right edge should not move backward. Such
constraint is enforced at DSS option generation time.
At the same time, the TCP stack ensures independently that the TCP-level
rcv wnd right's edge does not move backward. That in turn causes artificial
inflating of the MPTCP rcv window when the incoming data is acked at the
TCP level and is OoO in the MPTCP sequence space (or lands in the backlog).
As a consequence, the incoming traffic can exceed the receiver rcvbuf size
even when the sender is not misbehaving.
Prevent such scenario forcibly allowing the TCP subflow to shrink the
TCP-level rcv wnd regardless of the current netns setting. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: reject oversized EMA RNR lists
nl80211_parse_rnr_elems() stores the parsed element count in a
u8-backed cfg80211_rnr_elems::cnt field and uses that count to size
the flexible array allocation.
Reject nested NL80211_ATTR_EMA_RNR_ELEMS input once the count reaches
255, before incrementing it again. This keeps the parser aligned with
the data structure it fills and matches the existing bound check used
by nl80211_parse_mbssid_elems(). |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Limit XDomain response copy to actual frame size
tb_xdomain_copy() copies req->response_size bytes from the received
packet buffer regardless of the actual frame size. When a short
response arrives, this reads past the valid frame data in the DMA
pool buffer into stale contents from previous transactions.
Use the minimum of frame size and expected response size for the
copy length. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/umem: Fix truncation for block sizes >= 4G
When the iommu is used the linearization of the mapping can give a single
block that is very large split across multiple SG entries.
When __rdma_block_iter_next() reassembles the split SG entries it is
overflowing the 32 bit stack values and computed the wrong DMA addresses
for blocks after the truncation.
Use the right types to hold DMA addresses. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: fix potential unbounded skb queue
virtio_transport_inc_rx_pkt() checks vvs->rx_bytes + len > vvs->buf_alloc.
virtio_transport_recv_enqueue() skips coalescing for packets
with VIRTIO_VSOCK_SEQ_EOM.
If fed with packets with len == 0 and VIRTIO_VSOCK_SEQ_EOM,
a very large number of packets can be queued
because vvs->rx_bytes stays at 0.
Fix this by estimating the skb metadata size:
(Number of skbs in the queue) * SKB_TRUESIZE(0) |
| In the Linux kernel, the following vulnerability has been resolved:
s390/bpf: Zero-extend bpf prog return values and kfunc arguments
s390x ABI requires callers to zero-extend unsigned arguments and
sign-extend signed arguments, and callees to zero-extend unsigned
return values and sign-extend signed return values.
s390 BPF JIT currently implements only sign extension. Fix this
omission and implement zero extension too. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Use RCU-safe iteration in dev_map_redirect_multi() SKB path
The DEVMAP_HASH branch in dev_map_redirect_multi() uses
hlist_for_each_entry_safe() to iterate hash buckets, but this function
runs under RCU protection (called from xdp_do_generic_redirect_map()
in softirq context). Concurrent writers (__dev_map_hash_update_elem,
dev_map_hash_delete_elem) modify the list using RCU primitives
(hlist_add_head_rcu, hlist_del_rcu).
hlist_for_each_entry_safe() performs plain pointer dereferences without
rcu_dereference(), missing the acquire barrier needed to pair with
writers' rcu_assign_pointer(). On weakly-ordered architectures (ARM64,
POWER), a reader can observe a partially-constructed node. It also
defeats CONFIG_PROVE_RCU lockdep validation and KCSAN data-race
detection.
Replace with hlist_for_each_entry_rcu() using rcu_read_lock_bh_held()
as the lockdep condition, consistent with the rcu_dereference_check()
used in the DEVMAP (non-hash) branch of the same functions. Also fix
the same incorrect lockdep_is_held(&dtab->index_lock) condition in
dev_map_enqueue_multi(), where the lock is not held either. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix stale offload->prog pointer after constant blinding
When a dev-bound-only BPF program (BPF_F_XDP_DEV_BOUND_ONLY) undergoes
JIT compilation with constant blinding enabled (bpf_jit_harden >= 2),
bpf_jit_blind_constants() clones the program. The original prog is then
freed in bpf_jit_prog_release_other(), which updates aux->prog to point
to the surviving clone, but fails to update offload->prog.
This leaves offload->prog pointing to the freed original program. When
the network namespace is subsequently destroyed, cleanup_net() triggers
bpf_dev_bound_netdev_unregister(), which iterates ondev->progs and calls
__bpf_prog_offload_destroy(offload->prog). Accessing the freed prog
causes a page fault:
BUG: unable to handle page fault for address: ffffc900085f1038
Workqueue: netns cleanup_net
RIP: 0010:__bpf_prog_offload_destroy+0xc/0x80
Call Trace:
__bpf_offload_dev_netdev_unregister+0x257/0x350
bpf_dev_bound_netdev_unregister+0x4a/0x90
unregister_netdevice_many_notify+0x2a2/0x660
...
cleanup_net+0x21a/0x320
The test sequence that triggers this reliably is:
1. Set net.core.bpf_jit_harden=2 (echo 2 > /proc/sys/net/core/bpf_jit_harden)
2. Run xdp_metadata selftest, which creates a dev-bound-only XDP
program on a veth inside a netns (./test_progs -t xdp_metadata)
3. cleanup_net -> page fault in __bpf_prog_offload_destroy
Dev-bound-only programs are unique in that they have an offload structure
but go through the normal JIT path instead of bpf_prog_offload_compile().
This means they are subject to constant blinding's prog clone-and-replace,
while also having offload->prog that must stay in sync.
Fix this by updating offload->prog in bpf_jit_prog_release_other(),
alongside the existing aux->prog update. Both are back-pointers to
the prog that must be kept in sync when the prog is replaced. |
