| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
idpf: fix possible vport_config NULL pointer deref in remove
Attempting to remove the driver will cause a crash in cases where
the vport failed to initialize. Following trace is from an instance where
the driver failed during an attempt to create a VF:
[ 1661.543624] idpf 0000:84:00.7: Device HW Reset initiated
[ 1722.923726] idpf 0000:84:00.7: Transaction timed-out (op:1 cookie:2900 vc_op:1 salt:29 timeout:60000ms)
[ 1723.353263] BUG: kernel NULL pointer dereference, address: 0000000000000028
...
[ 1723.358472] RIP: 0010:idpf_remove+0x11c/0x200 [idpf]
...
[ 1723.364973] Call Trace:
[ 1723.365475] <TASK>
[ 1723.365972] pci_device_remove+0x42/0xb0
[ 1723.366481] device_release_driver_internal+0x1a9/0x210
[ 1723.366987] pci_stop_bus_device+0x6d/0x90
[ 1723.367488] pci_stop_and_remove_bus_device+0x12/0x20
[ 1723.367971] pci_iov_remove_virtfn+0xbd/0x120
[ 1723.368309] sriov_disable+0x34/0xe0
[ 1723.368643] idpf_sriov_configure+0x58/0x140 [idpf]
[ 1723.368982] sriov_numvfs_store+0xda/0x1c0
Avoid the NULL pointer dereference by adding NULL pointer check for
vport_config[i], before freeing user_config.q_coalesce. |
| In the Linux kernel, the following vulnerability has been resolved:
RISC-V: kexec: Fix memory leak of fdt buffer
This is reported by kmemleak detector:
unreferenced object 0xff60000082864000 (size 9588):
comm "kexec", pid 146, jiffies 4294900634 (age 64.788s)
hex dump (first 32 bytes):
d0 0d fe ed 00 00 12 ed 00 00 00 48 00 00 11 40 ...........H...@
00 00 00 28 00 00 00 11 00 00 00 02 00 00 00 00 ...(............
backtrace:
[<00000000f95b17c4>] kmemleak_alloc+0x34/0x3e
[<00000000b9ec8e3e>] kmalloc_order+0x9c/0xc4
[<00000000a95cf02e>] kmalloc_order_trace+0x34/0xb6
[<00000000f01e68b4>] __kmalloc+0x5c2/0x62a
[<000000002bd497b2>] kvmalloc_node+0x66/0xd6
[<00000000906542fa>] of_kexec_alloc_and_setup_fdt+0xa6/0x6ea
[<00000000e1166bde>] elf_kexec_load+0x206/0x4ec
[<0000000036548e09>] kexec_image_load_default+0x40/0x4c
[<0000000079fbe1b4>] sys_kexec_file_load+0x1c4/0x322
[<0000000040c62c03>] ret_from_syscall+0x0/0x2
In elf_kexec_load(), a buffer is allocated via kvmalloc() to store fdt.
While it's not freed back to system when kexec kernel is reloaded or
unloaded. Then memory leak is caused. Fix it by introducing riscv
specific function arch_kimage_file_post_load_cleanup(), and freeing the
buffer there. |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: qcom: q6v5: Fix potential null-ptr-deref in q6v5_wcss_init_mmio()
q6v5_wcss_init_mmio() will call platform_get_resource_byname() that may
fail and return NULL. devm_ioremap() will use res->start as input, which
may causes null-ptr-deref. Check the ret value of
platform_get_resource_byname() to avoid the null-ptr-deref. |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: ks-sa - fix division by zero in ks_sa_rng_init
Fix division by zero in ks_sa_rng_init caused by missing clock
pointer initialization. The clk_get_rate() call is performed on
an uninitialized clk pointer, resulting in division by zero when
calculating delay values.
Add clock initialization code before using the clock.
drivers/char/hw_random/ks-sa-rng.c | 7 +++++++
1 file changed, 7 insertions(+) |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache: free background tracker's queued work in btracker_destroy
Otherwise the kernel can BUG with:
[ 2245.426978] =============================================================================
[ 2245.435155] BUG bt_work (Tainted: G B W ): Objects remaining in bt_work on __kmem_cache_shutdown()
[ 2245.445233] -----------------------------------------------------------------------------
[ 2245.445233]
[ 2245.454879] Slab 0x00000000b0ce2b30 objects=64 used=2 fp=0x000000000a3c6a4e flags=0x17ffffc0000200(slab|node=0|zone=2|lastcpupid=0x1fffff)
[ 2245.467300] CPU: 7 PID: 10805 Comm: lvm Kdump: loaded Tainted: G B W 6.0.0-rc2 #19
[ 2245.476078] Hardware name: Dell Inc. PowerEdge R7525/0590KW, BIOS 2.5.6 10/06/2021
[ 2245.483646] Call Trace:
[ 2245.486100] <TASK>
[ 2245.488206] dump_stack_lvl+0x34/0x48
[ 2245.491878] slab_err+0x95/0xcd
[ 2245.495028] __kmem_cache_shutdown.cold+0x31/0x136
[ 2245.499821] kmem_cache_destroy+0x49/0x130
[ 2245.503928] btracker_destroy+0x12/0x20 [dm_cache]
[ 2245.508728] smq_destroy+0x15/0x60 [dm_cache_smq]
[ 2245.513435] dm_cache_policy_destroy+0x12/0x20 [dm_cache]
[ 2245.518834] destroy+0xc0/0x110 [dm_cache]
[ 2245.522933] dm_table_destroy+0x5c/0x120 [dm_mod]
[ 2245.527649] __dm_destroy+0x10e/0x1c0 [dm_mod]
[ 2245.532102] dev_remove+0x117/0x190 [dm_mod]
[ 2245.536384] ctl_ioctl+0x1a2/0x290 [dm_mod]
[ 2245.540579] dm_ctl_ioctl+0xa/0x20 [dm_mod]
[ 2245.544773] __x64_sys_ioctl+0x8a/0xc0
[ 2245.548524] do_syscall_64+0x5c/0x90
[ 2245.552104] ? syscall_exit_to_user_mode+0x12/0x30
[ 2245.556897] ? do_syscall_64+0x69/0x90
[ 2245.560648] ? do_syscall_64+0x69/0x90
[ 2245.564394] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 2245.569447] RIP: 0033:0x7fe52583ec6b
...
[ 2245.646771] ------------[ cut here ]------------
[ 2245.651395] kmem_cache_destroy bt_work: Slab cache still has objects when called from btracker_destroy+0x12/0x20 [dm_cache]
[ 2245.651408] WARNING: CPU: 7 PID: 10805 at mm/slab_common.c:478 kmem_cache_destroy+0x128/0x130
Found using: lvm2-testsuite --only "cache-single-split.sh"
Ben bisected and found that commit 0495e337b703 ("mm/slab_common:
Deleting kobject in kmem_cache_destroy() without holding
slab_mutex/cpu_hotplug_lock") first exposed dm-cache's incomplete
cleanup of its background tracker work objects. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix monitor mode bringup crash
When the interface is brought up in monitor mode, it leads
to NULL pointer dereference crash. This crash happens when
the packet type is extracted for a SKB. This extraction
which is present in the received msdu delivery path,is
not needed for the monitor ring packets since they are
all RAW packets. Hence appending the flags with
"RX_FLAG_ONLY_MONITOR" to skip that extraction.
Observed calltrace:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000064
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=0000000048517000
[0000000000000064] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
Modules linked in: ath11k_pci ath11k qmi_helpers
CPU: 2 PID: 1781 Comm: napi/-271 Not tainted
6.1.0-rc5-wt-ath-656295-gef907406320c-dirty #6
Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK10-C2 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
lr : ath11k_hw_qcn9074_rx_desc_get_decap_type+0x5c/0x60 [ath11k]
sp : ffff80000ef5bb10
x29: ffff80000ef5bb10 x28: 0000000000000000 x27: ffff000007baafa0
x26: ffff000014a91ed0 x25: 0000000000000000 x24: 0000000000000000
x23: ffff800002b77378 x22: ffff000014a91ec0 x21: ffff000006c8d600
x20: 0000000000000000 x19: ffff800002b77740 x18: 0000000000000006
x17: 736564203634343a x16: 656e694c20657079 x15: 0000000000000143
x14: 00000000ffffffea x13: ffff80000ef5b8b8 x12: ffff80000ef5b8c8
x11: ffff80000a591d30 x10: ffff80000a579d40 x9 : c0000000ffffefff
x8 : 0000000000000003 x7 : 0000000000017fe8 x6 : ffff80000a579ce8
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 3a35ec12ed7f8900 x1 : 0000000000000000 x0 : 0000000000000052
Call trace:
ath11k_hw_qcn9074_rx_desc_get_decap_type+0x34/0x60 [ath11k]
ath11k_dp_rx_deliver_msdu.isra.42+0xa4/0x3d0 [ath11k]
ath11k_dp_rx_mon_deliver.isra.43+0x2f8/0x458 [ath11k]
ath11k_dp_rx_process_mon_rings+0x310/0x4c0 [ath11k]
ath11k_dp_service_srng+0x234/0x338 [ath11k]
ath11k_pcic_ext_grp_napi_poll+0x30/0xb8 [ath11k]
__napi_poll+0x5c/0x190
napi_threaded_poll+0xf0/0x118
kthread+0xf4/0x110
ret_from_fork+0x10/0x20
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
media: dvb-usb: fix memory leak in dvb_usb_adapter_init()
Syzbot reports a memory leak in "dvb_usb_adapter_init()".
The leak is due to not accounting for and freeing current iteration's
adapter->priv in case of an error. Currently if an error occurs,
it will exit before incrementing "num_adapters_initalized",
which is used as a reference counter to free all adap->priv
in "dvb_usb_adapter_exit()". There are multiple error paths that
can exit from before incrementing the counter. Including the
error handling paths for "dvb_usb_adapter_stream_init()",
"dvb_usb_adapter_dvb_init()" and "dvb_usb_adapter_frontend_init()"
within "dvb_usb_adapter_init()".
This means that in case of an error in any of these functions the
current iteration is not accounted for and the current iteration's
adap->priv is not freed.
Fix this by freeing the current iteration's adap->priv in the
"stream_init_err:" label in the error path. The rest of the
(accounted for) adap->priv objects are freed in dvb_usb_adapter_exit()
as expected using the num_adapters_initalized variable.
Syzbot report:
BUG: memory leak
unreferenced object 0xffff8881172f1a00 (size 512):
comm "kworker/0:2", pid 139, jiffies 4294994873 (age 10.960s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff844af012>] dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:75 [inline]
[<ffffffff844af012>] dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:184 [inline]
[<ffffffff844af012>] dvb_usb_device_init.cold+0x4e5/0x79e drivers/media/usb/dvb-usb/dvb-usb-init.c:308
[<ffffffff830db21d>] dib0700_probe+0x8d/0x1b0 drivers/media/usb/dvb-usb/dib0700_core.c:883
[<ffffffff82d3fdc7>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752
[<ffffffff8274af6a>] driver_probe_device+0x2a/0x120 drivers/base/dd.c:782
[<ffffffff8274b786>] __device_attach_driver+0xf6/0x140 drivers/base/dd.c:899
[<ffffffff82747c87>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:427
[<ffffffff8274b352>] __device_attach+0x122/0x260 drivers/base/dd.c:970
[<ffffffff827498f6>] bus_probe_device+0xc6/0xe0 drivers/base/bus.c:487
[<ffffffff82745cdb>] device_add+0x5fb/0xdf0 drivers/base/core.c:3405
[<ffffffff82d3d202>] usb_set_configuration+0x8f2/0xb80 drivers/usb/core/message.c:2170
[<ffffffff82d4dbfc>] usb_generic_driver_probe+0x8c/0xc0 drivers/usb/core/generic.c:238
[<ffffffff82d3f49c>] usb_probe_device+0x5c/0x140 drivers/usb/core/driver.c:293
[<ffffffff8274ab37>] call_driver_probe drivers/base/dd.c:542 [inline]
[<ffffffff8274ab37>] really_probe.part.0+0xe7/0x310 drivers/base/dd.c:621
[<ffffffff8274ae6c>] really_probe drivers/base/dd.c:583 [inline]
[<ffffffff8274ae6c>] __driver_probe_device+0x10c/0x1e0 drivers/base/dd.c:752 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix crash while sending Action Frames in standalone AP Mode
Currently, whenever there is a need to transmit an Action frame,
the brcmfmac driver always uses the P2P vif to send the "actframe" IOVAR to
firmware. The P2P interfaces were available when wpa_supplicant is managing
the wlan interface.
However, the P2P interfaces are not created/initialized when only hostapd
is managing the wlan interface. And if hostapd receives an ANQP Query REQ
Action frame even from an un-associated STA, the brcmfmac driver tries
to use an uninitialized P2P vif pointer for sending the IOVAR to firmware.
This NULL pointer dereferencing triggers a driver crash.
[ 1417.074538] Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
[...]
[ 1417.075188] Hardware name: Raspberry Pi 4 Model B Rev 1.5 (DT)
[...]
[ 1417.075653] Call trace:
[ 1417.075662] brcmf_p2p_send_action_frame+0x23c/0xc58 [brcmfmac]
[ 1417.075738] brcmf_cfg80211_mgmt_tx+0x304/0x5c0 [brcmfmac]
[ 1417.075810] cfg80211_mlme_mgmt_tx+0x1b0/0x428 [cfg80211]
[ 1417.076067] nl80211_tx_mgmt+0x238/0x388 [cfg80211]
[ 1417.076281] genl_family_rcv_msg_doit+0xe0/0x158
[ 1417.076302] genl_rcv_msg+0x220/0x2a0
[ 1417.076317] netlink_rcv_skb+0x68/0x140
[ 1417.076330] genl_rcv+0x40/0x60
[ 1417.076343] netlink_unicast+0x330/0x3b8
[ 1417.076357] netlink_sendmsg+0x19c/0x3f8
[ 1417.076370] __sock_sendmsg+0x64/0xc0
[ 1417.076391] ____sys_sendmsg+0x268/0x2a0
[ 1417.076408] ___sys_sendmsg+0xb8/0x118
[ 1417.076427] __sys_sendmsg+0x90/0xf8
[ 1417.076445] __arm64_sys_sendmsg+0x2c/0x40
[ 1417.076465] invoke_syscall+0x50/0x120
[ 1417.076486] el0_svc_common.constprop.0+0x48/0xf0
[ 1417.076506] do_el0_svc+0x24/0x38
[ 1417.076525] el0_svc+0x30/0x100
[ 1417.076548] el0t_64_sync_handler+0x100/0x130
[ 1417.076569] el0t_64_sync+0x190/0x198
[ 1417.076589] Code: f9401e80 aa1603e2 f9403be1 5280e483 (f9400000)
Fix this, by always using the vif corresponding to the wdev on which the
Action frame Transmission request was initiated by the userspace. This way,
even if P2P vif is not available, the IOVAR is sent to firmware on AP vif
and the ANQP Query RESP Action frame is transmitted without crashing the
driver.
Move init_completion() for "send_af_done" from brcmf_p2p_create_p2pdev()
to brcmf_p2p_attach(). Because the former function would not get executed
when only hostapd is managing wlan interface, and it is not safe to do
reinit_completion() later in brcmf_p2p_tx_action_frame(), without any prior
init_completion().
And in the brcmf_p2p_tx_action_frame() function, the condition check for
P2P Presence response frame is not needed, since the wpa_supplicant is
properly sending the P2P Presense Response frame on the P2P-GO vif instead
of the P2P-Device vif.
[Cc stable] |
| In the Linux kernel, the following vulnerability has been resolved:
x86/kexec: Fix double-free of elf header buffer
After
b3e34a47f989 ("x86/kexec: fix memory leak of elf header buffer"),
freeing image->elf_headers in the error path of crash_load_segments()
is not needed because kimage_file_post_load_cleanup() will take
care of that later. And not clearing it could result in a double-free.
Drop the superfluous vfree() call at the error path of
crash_load_segments(). |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Move representor neigh cleanup to profile cleanup_tx
For IP tunnel encapsulation in ECMP (Equal-Cost Multipath) mode, as
the flow is duplicated to the peer eswitch, the related neighbour
information on the peer uplink representor is created as well.
In the cited commit, eswitch devcom unpair is moved to uplink unload
API, specifically the profile->cleanup_tx. If there is a encap rule
offloaded in ECMP mode, when one eswitch does unpair (because of
unloading the driver, for instance), and the peer rule from the peer
eswitch is going to be deleted, the use-after-free error is triggered
while accessing neigh info, as it is already cleaned up in uplink's
profile->disable, which is before its profile->cleanup_tx.
To fix this issue, move the neigh cleanup to profile's cleanup_tx
callback, and after mlx5e_cleanup_uplink_rep_tx is called. The neigh
init is moved to init_tx for symmeter.
[ 2453.376299] BUG: KASAN: slab-use-after-free in mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core]
[ 2453.379125] Read of size 4 at addr ffff888127af9008 by task modprobe/2496
[ 2453.381542] CPU: 7 PID: 2496 Comm: modprobe Tainted: G B 6.4.0-rc7+ #15
[ 2453.383386] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 2453.384335] Call Trace:
[ 2453.384625] <TASK>
[ 2453.384891] dump_stack_lvl+0x33/0x50
[ 2453.385285] print_report+0xc2/0x610
[ 2453.385667] ? __virt_addr_valid+0xb1/0x130
[ 2453.386091] ? mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core]
[ 2453.386757] kasan_report+0xae/0xe0
[ 2453.387123] ? mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core]
[ 2453.387798] mlx5e_rep_neigh_entry_release+0x109/0x3a0 [mlx5_core]
[ 2453.388465] mlx5e_rep_encap_entry_detach+0xa6/0xe0 [mlx5_core]
[ 2453.389111] mlx5e_encap_dealloc+0xa7/0x100 [mlx5_core]
[ 2453.389706] mlx5e_tc_tun_encap_dests_unset+0x61/0xb0 [mlx5_core]
[ 2453.390361] mlx5_free_flow_attr_actions+0x11e/0x340 [mlx5_core]
[ 2453.391015] ? complete_all+0x43/0xd0
[ 2453.391398] ? free_flow_post_acts+0x38/0x120 [mlx5_core]
[ 2453.392004] mlx5e_tc_del_fdb_flow+0x4ae/0x690 [mlx5_core]
[ 2453.392618] mlx5e_tc_del_fdb_peers_flow+0x308/0x370 [mlx5_core]
[ 2453.393276] mlx5e_tc_clean_fdb_peer_flows+0xf5/0x140 [mlx5_core]
[ 2453.393925] mlx5_esw_offloads_unpair+0x86/0x540 [mlx5_core]
[ 2453.394546] ? mlx5_esw_offloads_set_ns_peer.isra.0+0x180/0x180 [mlx5_core]
[ 2453.395268] ? down_write+0xaa/0x100
[ 2453.395652] mlx5_esw_offloads_devcom_event+0x203/0x530 [mlx5_core]
[ 2453.396317] mlx5_devcom_send_event+0xbb/0x190 [mlx5_core]
[ 2453.396917] mlx5_esw_offloads_devcom_cleanup+0xb0/0xd0 [mlx5_core]
[ 2453.397582] mlx5e_tc_esw_cleanup+0x42/0x120 [mlx5_core]
[ 2453.398182] mlx5e_rep_tc_cleanup+0x15/0x30 [mlx5_core]
[ 2453.398768] mlx5e_cleanup_rep_tx+0x6c/0x80 [mlx5_core]
[ 2453.399367] mlx5e_detach_netdev+0xee/0x120 [mlx5_core]
[ 2453.399957] mlx5e_netdev_change_profile+0x84/0x170 [mlx5_core]
[ 2453.400598] mlx5e_vport_rep_unload+0xe0/0xf0 [mlx5_core]
[ 2453.403781] mlx5_eswitch_unregister_vport_reps+0x15e/0x190 [mlx5_core]
[ 2453.404479] ? mlx5_eswitch_register_vport_reps+0x200/0x200 [mlx5_core]
[ 2453.405170] ? up_write+0x39/0x60
[ 2453.405529] ? kernfs_remove_by_name_ns+0xb7/0xe0
[ 2453.405985] auxiliary_bus_remove+0x2e/0x40
[ 2453.406405] device_release_driver_internal+0x243/0x2d0
[ 2453.406900] ? kobject_put+0x42/0x2d0
[ 2453.407284] bus_remove_device+0x128/0x1d0
[ 2453.407687] device_del+0x240/0x550
[ 2453.408053] ? waiting_for_supplier_show+0xe0/0xe0
[ 2453.408511] ? kobject_put+0xfa/0x2d0
[ 2453.408889] ? __kmem_cache_free+0x14d/0x280
[ 2453.409310] mlx5_rescan_drivers_locked.part.0+0xcd/0x2b0 [mlx5_core]
[ 2453.409973] mlx5_unregister_device+0x40/0x50 [mlx5_core]
[ 2453.410561] mlx5_uninit_one+0x3d/0x110 [mlx5_core]
[ 2453.411111] remove_one+0x89/0x130 [mlx5_core]
[ 24
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
media: rcar_fdp1: Fix refcount leak in probe and remove function
rcar_fcp_get() take reference, which should be balanced with
rcar_fcp_put(). Add missing rcar_fcp_put() in fdp1_remove and
the error paths of fdp1_probe() to fix this.
[hverkuil: resolve merge conflict, remove() is now void] |
| In the Linux kernel, the following vulnerability has been resolved:
posix-timers: Plug potential memory leak in do_timer_create()
When posix timer creation is set to allocate a given timer ID and the
access to the user space value faults, the function terminates without
freeing the already allocated posix timer structure.
Move the allocation after the user space access to cure that.
[ tglx: Massaged change log ] |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Don't overflow during division for dirty tracking
If pgshift is 63 then BITS_PER_TYPE(*bitmap->bitmap) * pgsize will overflow
to 0 and this triggers divide by 0.
In this case the index should just be 0, so reorganize things to divide
by shift and avoid hitting any overflows. |
| In the Linux kernel, the following vulnerability has been resolved:
uio: uio_dmem_genirq: Fix missing unlock in irq configuration
Commit b74351287d4b ("uio: fix a sleep-in-atomic-context bug in
uio_dmem_genirq_irqcontrol()") started calling disable_irq() without
holding the spinlock because it can sleep. However, that fix introduced
another bug: if interrupt is already disabled and a new disable request
comes in, then the spinlock is not unlocked:
root@localhost:~# printf '\x00\x00\x00\x00' > /dev/uio0
root@localhost:~# printf '\x00\x00\x00\x00' > /dev/uio0
root@localhost:~# [ 14.851538] BUG: scheduling while atomic: bash/223/0x00000002
[ 14.851991] Modules linked in: uio_dmem_genirq uio myfpga(OE) bochs drm_vram_helper drm_ttm_helper ttm drm_kms_helper drm snd_pcm ppdev joydev psmouse snd_timer snd e1000fb_sys_fops syscopyarea parport sysfillrect soundcore sysimgblt input_leds pcspkr i2c_piix4 serio_raw floppy evbug qemu_fw_cfg mac_hid pata_acpi ip_tables x_tables autofs4 [last unloaded: parport_pc]
[ 14.854206] CPU: 0 PID: 223 Comm: bash Tainted: G OE 6.0.0-rc7 #21
[ 14.854786] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
[ 14.855664] Call Trace:
[ 14.855861] <TASK>
[ 14.856025] dump_stack_lvl+0x4d/0x67
[ 14.856325] dump_stack+0x14/0x1a
[ 14.856583] __schedule_bug.cold+0x4b/0x5c
[ 14.856915] __schedule+0xe81/0x13d0
[ 14.857199] ? idr_find+0x13/0x20
[ 14.857456] ? get_work_pool+0x2d/0x50
[ 14.857756] ? __flush_work+0x233/0x280
[ 14.858068] ? __schedule+0xa95/0x13d0
[ 14.858307] ? idr_find+0x13/0x20
[ 14.858519] ? get_work_pool+0x2d/0x50
[ 14.858798] schedule+0x6c/0x100
[ 14.859009] schedule_hrtimeout_range_clock+0xff/0x110
[ 14.859335] ? tty_write_room+0x1f/0x30
[ 14.859598] ? n_tty_poll+0x1ec/0x220
[ 14.859830] ? tty_ldisc_deref+0x1a/0x20
[ 14.860090] schedule_hrtimeout_range+0x17/0x20
[ 14.860373] do_select+0x596/0x840
[ 14.860627] ? __kernel_text_address+0x16/0x50
[ 14.860954] ? poll_freewait+0xb0/0xb0
[ 14.861235] ? poll_freewait+0xb0/0xb0
[ 14.861517] ? rpm_resume+0x49d/0x780
[ 14.861798] ? common_interrupt+0x59/0xa0
[ 14.862127] ? asm_common_interrupt+0x2b/0x40
[ 14.862511] ? __uart_start.isra.0+0x61/0x70
[ 14.862902] ? __check_object_size+0x61/0x280
[ 14.863255] core_sys_select+0x1c6/0x400
[ 14.863575] ? vfs_write+0x1c9/0x3d0
[ 14.863853] ? vfs_write+0x1c9/0x3d0
[ 14.864121] ? _copy_from_user+0x45/0x70
[ 14.864526] do_pselect.constprop.0+0xb3/0xf0
[ 14.864893] ? do_syscall_64+0x6d/0x90
[ 14.865228] ? do_syscall_64+0x6d/0x90
[ 14.865556] __x64_sys_pselect6+0x76/0xa0
[ 14.865906] do_syscall_64+0x60/0x90
[ 14.866214] ? syscall_exit_to_user_mode+0x2a/0x50
[ 14.866640] ? do_syscall_64+0x6d/0x90
[ 14.866972] ? do_syscall_64+0x6d/0x90
[ 14.867286] ? do_syscall_64+0x6d/0x90
[ 14.867626] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[...] stripped
[ 14.872959] </TASK>
('myfpga' is a simple 'uio_dmem_genirq' driver I wrote to test this)
The implementation of "uio_dmem_genirq" was based on "uio_pdrv_genirq" and
it is used in a similar manner to the "uio_pdrv_genirq" driver with respect
to interrupt configuration and handling. At the time "uio_dmem_genirq" was
introduced, both had the same implementation of the 'uio_info' handlers
irqcontrol() and handler(). Then commit 34cb27528398 ("UIO: Fix concurrency
issue"), which was only applied to "uio_pdrv_genirq", ended up making them
a little different. That commit, among other things, changed disable_irq()
to disable_irq_nosync() in the implementation of irqcontrol(). The
motivation there was to avoid a deadlock between irqcontrol() and
handler(), since it added a spinlock in the irq handler, and disable_irq()
waits for the completion of the irq handler.
By changing disable_irq() to disable_irq_nosync() in irqcontrol(), we also
avoid the sleeping-whil
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: hide VRAM sysfs attributes on GPUs without VRAM
Otherwise accessing them can cause a crash. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda/hdmi: Fix breakage at probing nvhdmi-mcp driver
After restructuring and splitting the HDMI codec driver code, each
HDMI codec driver contains the own build_controls and build_pcms ops.
A copy-n-paste error put the wrong entries for nvhdmi-mcp driver; both
build_controls and build_pcms are swapped. Unfortunately both
callbacks have the very same form, and the compiler didn't complain
it, either. This resulted in a NULL dereference because the PCM
instance hasn't been initialized at calling the build_controls
callback.
Fix it by passing the proper entries. |
| In the Linux kernel, the following vulnerability has been resolved:
ipmi: fix use after free in _ipmi_destroy_user()
The intf_free() function frees the "intf" pointer so we cannot
dereference it again on the next line. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: int3472: Fix double free of GPIO device during unregister
regulator_unregister() already frees the associated GPIO device. On
ThinkPad X9 (Lunar Lake), this causes a double free issue that leads to
random failures when other drivers (typically Intel THC) attempt to
allocate interrupts. The root cause is that the reference count of the
pinctrl_intel_platform module unexpectedly drops to zero when this
driver defers its probe.
This behavior can also be reproduced by unloading the module directly.
Fix the issue by removing the redundant release of the GPIO device
during regulator unregistration. |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: arm: scmi: Fix genpd leak on provider registration failure
If of_genpd_add_provider_onecell() fails during probe, the previously
created generic power domains are not removed, leading to a memory leak
and potential kernel crash later in genpd_debug_add().
Add proper error handling to unwind the initialized domains before
returning from probe to ensure all resources are correctly released on
failure.
Example crash trace observed without this fix:
| Unable to handle kernel paging request at virtual address fffffffffffffc70
| CPU: 1 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.18.0-rc1 #405 PREEMPT
| Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform
| pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : genpd_debug_add+0x2c/0x160
| lr : genpd_debug_init+0x74/0x98
| Call trace:
| genpd_debug_add+0x2c/0x160 (P)
| genpd_debug_init+0x74/0x98
| do_one_initcall+0xd0/0x2d8
| do_initcall_level+0xa0/0x140
| do_initcalls+0x60/0xa8
| do_basic_setup+0x28/0x40
| kernel_init_freeable+0xe8/0x170
| kernel_init+0x2c/0x140
| ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: fix address removal logic in mptcp_pm_nl_rm_addr
Fix inverted WARN_ON_ONCE condition that prevented normal address
removal counter updates. The current code only executes decrement
logic when the counter is already 0 (abnormal state), while
normal removals (counter > 0) are ignored. |
