| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
w1: ds28e17: reject an oversize length on an I2C block read
w1_f19_i2c_master_transfer() is the master_xfer for the DS28E17 1-Wire
to I2C bridge. On an I2C_M_RECV_LEN read, it takes the length from the
device. The downstream slave puts a length byte in buf[0]. The driver
then reads that many bytes into buf[1] with w1_f19_i2c_read().
buf[0] is controlled by the device and can be 0 to 255.
w1_f19_i2c_read() only rejects a zero count. The caller buffer is
I2C_SMBUS_BLOCK_MAX + 2, so 34 bytes. A length above 32 makes the read
run past it, up to about 222 bytes out of bounds.
The SMBus core does check buf[0] against I2C_SMBUS_BLOCK_MAX. That
check runs after master_xfer returns. By then the write is already
done. i2c-algo-bit rejects an oversize length before it copies, and
returns -EPROTO.
Reject a length above I2C_SMBUS_BLOCK_MAX at both RECV_LEN sites, the
same way i2c-algo-bit does. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix netfs_read_folio() to wait on writeback
Fix netfs_read_folio() to wait for an ongoing writeback to complete so that
it can trust the dirty flag and whatever is attached to folio->private
(folio->private may get cleaned up by the collector before it clears the
writeback flag). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix same-register dst/src OOB read and pointer leak in sock_ops
When a BPF sock_ops program accesses ctx fields with dst_reg == src_reg,
the SOCK_OPS_GET_SK() and SOCK_OPS_GET_FIELD() macros fail to zero the
destination register in the !fullsock / !locked_tcp_sock path.
Both macros borrow a temporary register to check is_fullsock /
is_locked_tcp_sock when dst_reg == src_reg, because dst_reg holds the
ctx pointer. When the check is false (e.g., TCP_NEW_SYN_RECV state with
a request_sock), dst_reg should be zeroed but is not, leaving the stale
ctx pointer:
- SOCK_OPS_GET_SK: dst_reg retains the ctx pointer, passes NULL checks
as PTR_TO_SOCKET_OR_NULL, and can be used as a bogus socket pointer,
leading to stack-out-of-bounds access in helpers like
bpf_skc_to_tcp6_sock().
- SOCK_OPS_GET_FIELD: dst_reg retains the ctx pointer which the
verifier believes is a SCALAR_VALUE, leaking a kernel pointer.
Fix both macros by:
- Changing JMP_A(1) to JMP_A(2) in the fullsock path to skip the
added instruction.
- Adding BPF_MOV64_IMM(si->dst_reg, 0) after the temp register
restore in the !fullsock path, placed after the restore because
dst_reg == src_reg means we need src_reg intact to read ctx->temp. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix overflow in dacloffset bounds check
The dacloffset field was originally typed as int and used in an
unchecked addition, which could overflow and bypass the existing
bounds check in both smb_check_perm_dacl() and smb_inherit_dacl().
This could result in out-of-bounds memory access and a kernel crash
when dereferencing the DACL pointer.
This patch converts dacloffset to unsigned int and uses
check_add_overflow() to validate access to the DACL. |
| Acrobat Reader is affected by an out-of-bounds read vulnerability that could lead to disclosure of sensitive memory. An attacker could leverage this vulnerability to disclose sensitive information. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Acrobat Reader is affected by an out-of-bounds read vulnerability that could lead to disclosure of sensitive memory. An attacker could leverage this vulnerability to disclose sensitive information. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| An out-of-bounds read vulnerability was discovered in the Bosch BME690 SensorAPI (C-driver) in version v1.0.3 and prior, specifically within the field data parsing logic in read_all_field_data (bme69x.c).
The driver prefetches heater configuration registers into a contiguous 30-byte stack buffer (set_val) mapping IDAC, RES_HEAT, and GAS_WAIT tables.
When parsing sensor field data, the gas_index is extracted using a 4-bit mask (0..15) but lacks boundary verification against the valid range (0..9).
An attacker or a compromised peripheral mimicking a sensor on the I2C/SPI bus could return a payload with a gas index value of 10 or higher.
This causes the driver to perform an out-of-bounds array access (set_val[20 + gas_index]), reading up to 6 bytes past the stack buffer.
The leaked out-of-bounds byte is then written into the public gas_wait field, which may lead to measurement corruption or leak adjacent stack memory when telemetered or logged. |
| Netskope was notified of an out-of-bounds heap read affecting the Endpoint DLP (EPDLP) service of the Netskope Client. A local standard user could potentially send a specially crafted message that is not properly validated with a bounds check, likely crashing the kernel driver handler. Successful exploitation could potentially crash the EPDLP service, temporarily interrupting DLP enforcement. A successful exploit could potentially also reveal per-boot memory layout information to unauthorized users. |
| Out-of-bounds read vulnerability in Citirx Workspace app for Windows.
This issue affects Workspace app for Windows: before 2603.11 Current Release (CR), before 2507.1 LTSR CU3, and before LTSR 2607. |
| Out-of-bounds read in Microsoft Office Word allows an unauthorized attacker to disclose information over a network. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: nsm: bound the device-reported response length
nsm_sendrecv_msg_locked() stores the virtqueue used-ring length reported
by the NSM device into msg->resp.len without bounding it to the response
buffer. A malicious or buggy backend can report a length larger than the
response buffer; parse_resp_raw() then copies that many bytes out of the
fixed buffer to user space, disclosing adjacent kernel heap (an
out-of-bounds read). The request path already floors its length in
fill_req_raw(); the response path lacks the symmetric check.
Clamp the stored length to the size of the response buffer. Well-behaved
devices report no more than the posted buffer size, so conforming traffic
is unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: clear opcnt on compound arg release to prevent OOB read
nfsd4_release_compoundargs() resets args->ops to the inline iops[8]
array when the dynamically-allocated ops buffer is freed, but leaves
args->opcnt at its original value (which can be up to 200 for NFSv4.1+
compounds).
If rq_status_counter is stuck at an odd value (which can happen when
nfsd_dispatch() hits an error path after setting it odd), the RPC
status dumpit handler reads min(opcnt, 16) entries from args->ops[].
Since iops only has 8 elements and is the last field in struct
nfsd4_compoundargs, reading indices 8-15 accesses adjacent slab memory
and leaks it to userspace via netlink.
Zero opcnt unconditionally in nfsd4_release_compoundargs() so stale
compound metadata is never exposed through the status interface.
[ cel: Remove the kvfree_rcu_mightsleep() sleep from the exposure window ] |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: bound MDSCapAuth path and fs_name decode in handle_session()
handle_session() decodes the MDSCapAuth records carried by a
CEPH_SESSION_OPEN message (msg_version >= 6). For each record the
match.path and match.fs_name byte strings are read by first decoding a
32-bit length and then copying that many bytes with the bare
ceph_decode_copy(). Unlike the surrounding fields, which all use the
_safe decode variants, these two copies are not preceded by a
ceph_decode_need() bounds check, and the enclosing MDSCapAuth and
MDSCapMatch struct_len fields are skipped rather than enforced as an
upper bound. A length larger than the bytes remaining in the message
front makes ceph_decode_copy() read past the end of the front buffer.
The message front is a dedicated allocation (ceph_msg_new2() ->
kvmalloc), so the over-read runs off that object. A malicious or
compromised MDS can trigger this with the first post-connect message on
mount, with no client-side user interaction; under KASAN it is reported
as a slab-out-of-bounds read in handle_session().
Impact: a malicious MDS can force the kernel client to read up to 4 GiB
past the message front allocation during session setup, crashing the
client (out-of-bounds read).
Switch both copies to ceph_decode_copy_safe(), which performs the
ceph_decode_need() bounds check before the copy and branches to the
existing bad label, matching the rest of the decoder and the error path
that frees the partially decoded cap_auths array. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: restore the data_offset bound in is_valid_oplock_break()
Commit 83bfbd0bb902 ("cifs: Remove the RFC1002 header from smb_hdr")
changed the quantity this bound is measured against. It used to be
srv->total_read minus the 4-byte RFC1002 preamble that total_read then
included, so it was the SMB message length. The same commit stopped
counting the preamble, and the mechanical substitution to
srv->total_read - srv->pdu_size left an expression that is identically
zero: standard_receive3() reads MID_HEADER_SIZE() bytes and then exactly
pdu_length - MID_HEADER_SIZE() more, adding both to total_read.
len is therefore 0, the subtraction below it wraps, and no __u32
DataOffset can exceed the result, so the check from commit 097f5863b1a0
("cifs: read overflow in is_valid_oplock_break()") no longer rejects
anything. Use total_read, which is now the message length on its own. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: bound the free-cluster bitmap scan to the volume
vol->lcn_empty_bits_per_page is sized from vol->nr_clusters at mount, but
ntfs_cluster_alloc() bounds its scan of that array by the size of $Bitmap.
Those are independent on-disk quantities and the mount-time check only
rejects a $Bitmap that is too small, so an image whose $Bitmap covers more
clusters than the volume has lets the scan index past the array. A run
whose LCN lies in that gap takes the allocator straight there, since the
caller passes the file's own last LCN as its locality hint. KASAN reports
a slab out-of-bounds read when a file on such a volume is extended.
Clamp the scan to what that array covers, mirroring the max_index
calculation the mount-time scan already uses, and reject a decoded LCN
at or beyond nr_clusters in the mapping pairs decoder. Conforming
volumes are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: APEI: GHES: fix ARM section length accounting after header
In ghes_handle_arm_hw_error(), after skipping the cper_sec_proc_arm
header with (err + 1), the remaining length was reduced by sizeof(err)
(pointer size) instead of sizeof(*err) (structure size).
That overestimates the bytes left for cper_arm_err_info records and can
let the parser read past the CPER section when err_info_num is large
enough relative to error_data_length.
Use sizeof(*err) so the length accounting matches the pointer advance
and the earlier sizeof(*err) size check. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/features: bound fwctl command payload to the input buffer
fwctl_cmd_rpc() copies cmd->in_len bytes into inbuf = kvzalloc(cmd->in_len)
and passes inbuf and in_len to ->fw_rpc(). The CXL callback cxlctl_fw_rpc()
ignores in_len and never checks the user-controlled op_size against it.
cxlctl_set_feature() bounds op_size only from below
(op_size <= sizeof(feat_in->hdr)) and then reads op_size - sizeof(hdr)
bytes from feat_in->feat_data via cxl_set_feature(). With a small in_len
and a large op_size the first memcpy() already reads past the
kvzalloc(in_len) buffer; the out-of-bounds bytes are placed in the mailbox
payload and sent to the device, and a large enough op_size can walk into
unmapped memory and oops the kernel. The Get paths pin op_size to a fixed
size but likewise read the input struct without checking in_len.
Reject, at the single dispatch point, any request whose fixed header plus
op_size does not fit in the copied-in buffer. The lower-bound test guards
the subtraction and ensures op_size was copied in before it is read. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: carry oversized SMC-Rv2 LLC messages in the queue entry
smc_llc_rmt_delete_rkey() and smc_llc_save_add_link_rkeys() read the part
of a v2 message that does not fit into the 44-byte union smc_llc_msg, and
both bound themselves by the size of the buffer it landed in, not by what
arrived. On a link with a shared v2 receive buffer a 44-byte
DELETE_RKEY_V2 declaring 255 rkeys reaches rkey[9..254] in whatever an
earlier message left in lgr->wr_rx_buf_v2, and passes each of them to
smc_rtoken_delete(). One of those 255 matched a registered rtoken and
deleted it. An ADD_LINK on such a link installs up to 255 rtokens from
the same bytes.
Copy the tail into the queue entry, so its length is the length of the
message that arrived, and declare the rkeys that fit inline as a member of
the union instead of reaching them through a cast. The same
DELETE_RKEY_V2 now processes the 9 rkeys it carries. The copy is limited
to the longest tail the two functions can read, so the peer does not pick
the size of the entry.
The bound the previous patch placed on links without a shared v2 receive
buffer is no longer needed. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-pcache: validate geometry fields from on-disk cache_info
cache_segs_init() iterates cache_info->n_segs times indexing
cache->segments[], which is sized to the cache device geometry, and
get_seg_id() takes each segment id from the on-media cache_info and the
per-segment next_seg link. Both come from cache device metadata that is
only CRC-protected with a fixed public seed, so whoever supplies the
cache device on a table load (CAP_SYS_ADMIN) controls them: an oversized
n_segs or an out-of-range id drives an out-of-bounds access of
cache->segments[] and a wild CACHE_DEV_SEGMENT() pointer into the device
mapping -- an out-of-bounds read and write from on-disk data.
Reject an n_segs that exceeds the device segment count and a segment id
that is out of range before either is used. Valid metadata is unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-pcache: validate kset key_num and intra-segment bounds
Two more fields decoded from the cache device go unbounded. The kset
key_num drives cache_kset_crc() and the replay loop in cache_replay(),
the writeback worker and the GC worker, but only the magic and a
fixed-seed CRC are checked first, so a non-last kset whose key_num exceeds
the PCACHE_KSET_KEYS_MAX buffer reads past its end before the CRC compare.
A key's intra-segment offset and length in cache_key_decode() are taken
verbatim, so a key running past its segment is replayed into the cache
tree and the data CRC check and every later read hit then copy adjacent
persistent memory into the caller's bio -- an out-of-bounds read that
leaks to user space. Both fields are controlled by whoever supplies the
cache device (CAP_SYS_ADMIN); the CRC seed is public.
Add kset_onmedia_valid() to bound key_num before any kset read, and
reject a key whose offset plus length, computed in 64 bits, exceeds the
segment data_size. Valid metadata is unaffected. |
