| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Improper check for unusual or exceptional conditions in the Linux kernel-mode driver for some Intel(R) 800 Series Ethernet before version 1.17.2 may allow an authenticated user to potentially enable escalation of privilege via local access. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix WARN_ON in tracing_buffers_mmap_close for split VMAs
When a VMA is split (e.g., by partial munmap or MAP_FIXED), the kernel
calls vm_ops->close on each portion. For trace buffer mappings, this
results in ring_buffer_unmap() being called multiple times while
ring_buffer_map() was only called once.
This causes ring_buffer_unmap() to return -ENODEV on subsequent calls
because user_mapped is already 0, triggering a WARN_ON.
Trace buffer mappings cannot support partial mappings because the ring
buffer structure requires the complete buffer including the meta page.
Fix this by adding a may_split callback that returns -EINVAL to prevent
VMA splits entirely. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/memfd: fix information leak in hugetlb folios
When allocating hugetlb folios for memfd, three initialization steps are
missing:
1. Folios are not zeroed, leading to kernel memory disclosure to userspace
2. Folios are not marked uptodate before adding to page cache
3. hugetlb_fault_mutex is not taken before hugetlb_add_to_page_cache()
The memfd allocation path bypasses the normal page fault handler
(hugetlb_no_page) which would handle all of these initialization steps.
This is problematic especially for udmabuf use cases where folios are
pinned and directly accessed by userspace via DMA.
Fix by matching the initialization pattern used in hugetlb_no_page():
- Zero the folio using folio_zero_user() which is optimized for huge pages
- Mark it uptodate with folio_mark_uptodate()
- Take hugetlb_fault_mutex before adding to page cache to prevent races
The folio_zero_user() change also fixes a potential security issue where
uninitialized kernel memory could be disclosed to userspace through read()
or mmap() operations on the memfd. |
| In the Linux kernel, the following vulnerability has been resolved:
loop: loop_set_status_from_info() check before assignment
In loop_set_status_from_info(), lo->lo_offset and lo->lo_sizelimit should
be checked before reassignment, because if an overflow error occurs, the
original correct value will be changed to the wrong value, and it will not
be changed back.
More, the original patch did not solve the problem, the value was set and
ioctl returned an error, but the subsequent io used the value in the loop
driver, which still caused an alarm:
loop_handle_cmd
do_req_filebacked
loff_t pos = ((loff_t) blk_rq_pos(rq) << 9) + lo->lo_offset;
lo_rw_aio
cmd->iocb.ki_pos = pos |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: hisilicon/qm - set NULL to qm->debug.qm_diff_regs
When the initialization of qm->debug.acc_diff_reg fails,
the probe process does not exit. However, after qm->debug.qm_diff_regs is
freed, it is not set to NULL. This can lead to a double free when the
remove process attempts to free it again. Therefore, qm->debug.qm_diff_regs
should be set to NULL after it is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
mailbox: zynq-ipi: fix error handling while device_register() fails
If device_register() fails, it has two issues:
1. The name allocated by dev_set_name() is leaked.
2. The parent of device is not NULL, device_unregister() is called
in zynqmp_ipi_free_mboxes(), it will lead a kernel crash because
of removing not added device.
Call put_device() to give up the reference, so the name is freed in
kobject_cleanup(). Add device registered check in zynqmp_ipi_free_mboxes()
to avoid null-ptr-deref. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_vti: fix slab-use-after-free in decode_session6
When ipv6_vti device is set to the qdisc of the sfb type, the cb field
of the sent skb may be modified during enqueuing. Then,
slab-use-after-free may occur when ipv6_vti device sends IPv6 packets.
The stack information is as follows:
BUG: KASAN: slab-use-after-free in decode_session6+0x103f/0x1890
Read of size 1 at addr ffff88802e08edc2 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.4.0-next-20230707-00001-g84e2cad7f979 #410
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0xd9/0x150
print_address_description.constprop.0+0x2c/0x3c0
kasan_report+0x11d/0x130
decode_session6+0x103f/0x1890
__xfrm_decode_session+0x54/0xb0
vti6_tnl_xmit+0x3e6/0x1ee0
dev_hard_start_xmit+0x187/0x700
sch_direct_xmit+0x1a3/0xc30
__qdisc_run+0x510/0x17a0
__dev_queue_xmit+0x2215/0x3b10
neigh_connected_output+0x3c2/0x550
ip6_finish_output2+0x55a/0x1550
ip6_finish_output+0x6b9/0x1270
ip6_output+0x1f1/0x540
ndisc_send_skb+0xa63/0x1890
ndisc_send_rs+0x132/0x6f0
addrconf_rs_timer+0x3f1/0x870
call_timer_fn+0x1a0/0x580
expire_timers+0x29b/0x4b0
run_timer_softirq+0x326/0x910
__do_softirq+0x1d4/0x905
irq_exit_rcu+0xb7/0x120
sysvec_apic_timer_interrupt+0x97/0xc0
</IRQ>
Allocated by task 9176:
kasan_save_stack+0x22/0x40
kasan_set_track+0x25/0x30
__kasan_slab_alloc+0x7f/0x90
kmem_cache_alloc_node+0x1cd/0x410
kmalloc_reserve+0x165/0x270
__alloc_skb+0x129/0x330
netlink_sendmsg+0x9b1/0xe30
sock_sendmsg+0xde/0x190
____sys_sendmsg+0x739/0x920
___sys_sendmsg+0x110/0x1b0
__sys_sendmsg+0xf7/0x1c0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Freed by task 9176:
kasan_save_stack+0x22/0x40
kasan_set_track+0x25/0x30
kasan_save_free_info+0x2b/0x40
____kasan_slab_free+0x160/0x1c0
slab_free_freelist_hook+0x11b/0x220
kmem_cache_free+0xf0/0x490
skb_free_head+0x17f/0x1b0
skb_release_data+0x59c/0x850
consume_skb+0xd2/0x170
netlink_unicast+0x54f/0x7f0
netlink_sendmsg+0x926/0xe30
sock_sendmsg+0xde/0x190
____sys_sendmsg+0x739/0x920
___sys_sendmsg+0x110/0x1b0
__sys_sendmsg+0xf7/0x1c0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The buggy address belongs to the object at ffff88802e08ed00
which belongs to the cache skbuff_small_head of size 640
The buggy address is located 194 bytes inside of
freed 640-byte region [ffff88802e08ed00, ffff88802e08ef80)
As commit f855691975bb ("xfrm6: Fix the nexthdr offset in
_decode_session6.") showed, xfrm_decode_session was originally intended
only for the receive path. IP6CB(skb)->nhoff is not set during
transmission. Therefore, set the cb field in the skb to 0 before
sending packets. |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Do not warn in ring_buffer_map_get_reader() when reader catches up
The function ring_buffer_map_get_reader() is a bit more strict than the
other get reader functions, and except for certain situations the
rb_get_reader_page() should not return NULL. If it does, it triggers a
warning.
This warning was triggering but after looking at why, it was because
another acceptable situation was happening and it wasn't checked for.
If the reader catches up to the writer and there's still data to be read
on the reader page, then the rb_get_reader_page() will return NULL as
there's no new page to get.
In this situation, the reader page should not be updated and no warning
should trigger. |
| In the Linux kernel, the following vulnerability has been resolved:
ftrace: Fix softlockup in ftrace_module_enable
A soft lockup was observed when loading amdgpu module.
If a module has a lot of tracable functions, multiple calls
to kallsyms_lookup can spend too much time in RCU critical
section and with disabled preemption, causing kernel panic.
This is the same issue that was fixed in
commit d0b24b4e91fc ("ftrace: Prevent RCU stall on PREEMPT_VOLUNTARY
kernels") and commit 42ea22e754ba ("ftrace: Add cond_resched() to
ftrace_graph_set_hash()").
Fix it the same way by adding cond_resched() in ftrace_module_enable. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mscc: ocelot: Fix use-after-free caused by cyclic delayed work
The origin code calls cancel_delayed_work() in ocelot_stats_deinit()
to cancel the cyclic delayed work item ocelot->stats_work. However,
cancel_delayed_work() may fail to cancel the work item if it is already
executing. While destroy_workqueue() does wait for all pending work items
in the work queue to complete before destroying the work queue, it cannot
prevent the delayed work item from being rescheduled within the
ocelot_check_stats_work() function. This limitation exists because the
delayed work item is only enqueued into the work queue after its timer
expires. Before the timer expiration, destroy_workqueue() has no visibility
of this pending work item. Once the work queue appears empty,
destroy_workqueue() proceeds with destruction. When the timer eventually
expires, the delayed work item gets queued again, leading to the following
warning:
workqueue: cannot queue ocelot_check_stats_work on wq ocelot-switch-stats
WARNING: CPU: 2 PID: 0 at kernel/workqueue.c:2255 __queue_work+0x875/0xaf0
...
RIP: 0010:__queue_work+0x875/0xaf0
...
RSP: 0018:ffff88806d108b10 EFLAGS: 00010086
RAX: 0000000000000000 RBX: 0000000000000101 RCX: 0000000000000027
RDX: 0000000000000027 RSI: 0000000000000004 RDI: ffff88806d123e88
RBP: ffffffff813c3170 R08: 0000000000000000 R09: ffffed100da247d2
R10: ffffed100da247d1 R11: ffff88806d123e8b R12: ffff88800c00f000
R13: ffff88800d7285c0 R14: ffff88806d0a5580 R15: ffff88800d7285a0
FS: 0000000000000000(0000) GS:ffff8880e5725000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe18e45ea10 CR3: 0000000005e6c000 CR4: 00000000000006f0
Call Trace:
<IRQ>
? kasan_report+0xc6/0xf0
? __pfx_delayed_work_timer_fn+0x10/0x10
? __pfx_delayed_work_timer_fn+0x10/0x10
call_timer_fn+0x25/0x1c0
__run_timer_base.part.0+0x3be/0x8c0
? __pfx_delayed_work_timer_fn+0x10/0x10
? rcu_sched_clock_irq+0xb06/0x27d0
? __pfx___run_timer_base.part.0+0x10/0x10
? try_to_wake_up+0xb15/0x1960
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
tmigr_handle_remote_up+0x603/0x7e0
? __pfx_tmigr_handle_remote_up+0x10/0x10
? sched_balance_trigger+0x1c0/0x9f0
? sched_tick+0x221/0x5a0
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
? tick_nohz_handler+0x339/0x440
? __pfx_tmigr_handle_remote_up+0x10/0x10
__walk_groups.isra.0+0x42/0x150
tmigr_handle_remote+0x1f4/0x2e0
? __pfx_tmigr_handle_remote+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
? hrtimer_interrupt+0x322/0x780
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
The following diagram reveals the cause of the above warning:
CPU 0 (remove) | CPU 1 (delayed work callback)
mscc_ocelot_remove() |
ocelot_deinit() | ocelot_check_stats_work()
ocelot_stats_deinit() |
cancel_delayed_work()| ...
| queue_delayed_work()
destroy_workqueue() | (wait a time)
| __queue_work() //UAF
The above scenario actually constitutes a UAF vulnerability.
The ocelot_stats_deinit() is only invoked when initialization
failure or resource destruction, so we must ensure that any
delayed work items cannot be rescheduled.
Replace cancel_delayed_work() with disable_delayed_work_sync()
to guarantee proper cancellation of the delayed work item and
ensure completion of any currently executing work before the
workqueue is deallocated.
A deadlock concern was considered: ocelot_stats_deinit() is called
in a process context and is not holding any locks that the delayed
work item might also need. Therefore, the use of the _sync() variant
is safe here.
This bug was identified through static analysis. To reproduce the
issue and validate the fix, I simulated ocelot-swit
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: Protect regulator_supply_alias_list with regulator_list_mutex
regulator_supply_alias_list was accessed without any locking in
regulator_supply_alias(), regulator_register_supply_alias(), and
regulator_unregister_supply_alias(). Concurrent registration,
unregistration and lookups can race, leading to:
1 use-after-free if an alias entry is removed while being read,
2 duplicate entries when two threads register the same alias,
3 inconsistent alias mappings observed by consumers.
Protect all traversals, insertions and deletions on
regulator_supply_alias_list with the existing regulator_list_mutex. |
| In the Linux kernel, the following vulnerability has been resolved:
kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
syzkaller found a memory leak in kcm_sendmsg(), and commit c821a88bd720
("kcm: Fix memory leak in error path of kcm_sendmsg()") suppressed it by
updating kcm_tx_msg(head)->last_skb if partial data is copied so that the
following sendmsg() will resume from the skb.
However, we cannot know how many bytes were copied when we get the error.
Thus, we could mess up the MSG_MORE queue.
When kcm_sendmsg() fails for SOCK_DGRAM, we should purge the queue as we
do so for UDP by udp_flush_pending_frames().
Even without this change, when the error occurred, the following sendmsg()
resumed from a wrong skb and the queue was messed up. However, we have
yet to get such a report, and only syzkaller stumbled on it. So, this
can be changed safely.
Note this does not change SOCK_SEQPACKET behaviour. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix warning when putting transaction with qgroups enabled after abort
If we have a transaction abort with qgroups enabled we get a warning
triggered when doing the final put on the transaction, like this:
[552.6789] ------------[ cut here ]------------
[552.6815] WARNING: CPU: 4 PID: 81745 at fs/btrfs/transaction.c:144 btrfs_put_transaction+0x123/0x130 [btrfs]
[552.6817] Modules linked in: btrfs blake2b_generic xor (...)
[552.6819] CPU: 4 PID: 81745 Comm: btrfs-transacti Tainted: G W 6.4.0-rc6-btrfs-next-134+ #1
[552.6819] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[552.6819] RIP: 0010:btrfs_put_transaction+0x123/0x130 [btrfs]
[552.6821] Code: bd a0 01 00 (...)
[552.6821] RSP: 0018:ffffa168c0527e28 EFLAGS: 00010286
[552.6821] RAX: ffff936042caed00 RBX: ffff93604a3eb448 RCX: 0000000000000000
[552.6821] RDX: ffff93606421b028 RSI: ffffffff92ff0878 RDI: ffff93606421b010
[552.6821] RBP: ffff93606421b000 R08: 0000000000000000 R09: ffffa168c0d07c20
[552.6821] R10: 0000000000000000 R11: ffff93608dc52950 R12: ffffa168c0527e70
[552.6821] R13: ffff93606421b000 R14: ffff93604a3eb420 R15: ffff93606421b028
[552.6821] FS: 0000000000000000(0000) GS:ffff93675fb00000(0000) knlGS:0000000000000000
[552.6821] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[552.6821] CR2: 0000558ad262b000 CR3: 000000014feda005 CR4: 0000000000370ee0
[552.6822] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[552.6822] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[552.6822] Call Trace:
[552.6822] <TASK>
[552.6822] ? __warn+0x80/0x130
[552.6822] ? btrfs_put_transaction+0x123/0x130 [btrfs]
[552.6824] ? report_bug+0x1f4/0x200
[552.6824] ? handle_bug+0x42/0x70
[552.6824] ? exc_invalid_op+0x14/0x70
[552.6824] ? asm_exc_invalid_op+0x16/0x20
[552.6824] ? btrfs_put_transaction+0x123/0x130 [btrfs]
[552.6826] btrfs_cleanup_transaction+0xe7/0x5e0 [btrfs]
[552.6828] ? _raw_spin_unlock_irqrestore+0x23/0x40
[552.6828] ? try_to_wake_up+0x94/0x5e0
[552.6828] ? __pfx_process_timeout+0x10/0x10
[552.6828] transaction_kthread+0x103/0x1d0 [btrfs]
[552.6830] ? __pfx_transaction_kthread+0x10/0x10 [btrfs]
[552.6832] kthread+0xee/0x120
[552.6832] ? __pfx_kthread+0x10/0x10
[552.6832] ret_from_fork+0x29/0x50
[552.6832] </TASK>
[552.6832] ---[ end trace 0000000000000000 ]---
This corresponds to this line of code:
void btrfs_put_transaction(struct btrfs_transaction *transaction)
{
(...)
WARN_ON(!RB_EMPTY_ROOT(
&transaction->delayed_refs.dirty_extent_root));
(...)
}
The warning happens because btrfs_qgroup_destroy_extent_records(), called
in the transaction abort path, we free all entries from the rbtree
"dirty_extent_root" with rbtree_postorder_for_each_entry_safe(), but we
don't actually empty the rbtree - it's still pointing to nodes that were
freed.
So set the rbtree's root node to NULL to avoid this warning (assign
RB_ROOT). |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: Fix DMA mappings leak
During reallocation of RX buffers, new DMA mappings are created for
those buffers.
steps for reproduction:
while :
do
for ((i=0; i<=8160; i=i+32))
do
ethtool -G enp130s0f0 rx $i tx $i
sleep 0.5
ethtool -g enp130s0f0
done
done
This resulted in crash:
i40e 0000:01:00.1: Unable to allocate memory for the Rx descriptor ring, size=65536
Driver BUG
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:141 xdp_rxq_info_unreg+0x43/0x50
Call Trace:
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
Missing register, driver bug
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:119 xdp_rxq_info_unreg_mem_model+0x69/0x140
Call Trace:
xdp_rxq_info_unreg+0x1e/0x50
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
This was caused because of new buffers with different RX ring count should
substitute older ones, but those buffers were freed in
i40e_configure_rx_ring and reallocated again with i40e_alloc_rx_bi,
thus kfree on rx_bi caused leak of already mapped DMA.
Fix this by reallocating ZC with rx_bi_zc struct when BPF program loads. Additionally
reallocate back to rx_bi when BPF program unloads.
If BPF program is loaded/unloaded and XSK pools are created, reallocate
RX queues accordingly in XSP_SETUP_XSK_POOL handler. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/mxsfb: Disable overlay plane in mxsfb_plane_overlay_atomic_disable()
When disabling overlay plane in mxsfb_plane_overlay_atomic_update(),
overlay plane's framebuffer pointer is NULL. So, dereferencing it would
cause a kernel Oops(NULL pointer dereferencing). Fix the issue by
disabling overlay plane in mxsfb_plane_overlay_atomic_disable() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: allocate s_dio_done_wq for async reads as well
Since commit 222f2c7c6d14 ("iomap: always run error completions in user
context"), read error completions are deferred to s_dio_done_wq. This
means the workqueue also needs to be allocated for async reads. |
| In the Linux kernel, the following vulnerability has been resolved:
ubi: Fix UAF wear-leveling entry in eraseblk_count_seq_show()
Wear-leveling entry could be freed in error path, which may be accessed
again in eraseblk_count_seq_show(), for example:
__erase_worker eraseblk_count_seq_show
wl = ubi->lookuptbl[*block_number]
if (wl)
wl_entry_destroy
ubi->lookuptbl[e->pnum] = NULL
kmem_cache_free(ubi_wl_entry_slab, e)
erase_count = wl->ec // UAF!
Wear-leveling entry updating/accessing in ubi->lookuptbl should be
protected by ubi->wl_lock, fix it by adding ubi->wl_lock to serialize
wl entry accessing between wl_entry_destroy() and
eraseblk_count_seq_show().
Fetch a reproducer in [Link]. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: ocelot: call dsa_tag_8021q_unregister() under rtnl_lock() on driver remove
When the tagging protocol in current use is "ocelot-8021q" and we unbind
the driver, we see this splat:
$ echo '0000:00:00.2' > /sys/bus/pci/drivers/fsl_enetc/unbind
mscc_felix 0000:00:00.5 swp0: left promiscuous mode
sja1105 spi2.0: Link is Down
DSA: tree 1 torn down
mscc_felix 0000:00:00.5 swp2: left promiscuous mode
sja1105 spi2.2: Link is Down
DSA: tree 3 torn down
fsl_enetc 0000:00:00.2 eno2: left promiscuous mode
mscc_felix 0000:00:00.5: Link is Down
------------[ cut here ]------------
RTNL: assertion failed at net/dsa/tag_8021q.c (409)
WARNING: CPU: 1 PID: 329 at net/dsa/tag_8021q.c:409 dsa_tag_8021q_unregister+0x12c/0x1a0
Modules linked in:
CPU: 1 PID: 329 Comm: bash Not tainted 6.5.0-rc3+ #771
pc : dsa_tag_8021q_unregister+0x12c/0x1a0
lr : dsa_tag_8021q_unregister+0x12c/0x1a0
Call trace:
dsa_tag_8021q_unregister+0x12c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
RTNL: assertion failed at net/8021q/vlan_core.c (376)
WARNING: CPU: 1 PID: 329 at net/8021q/vlan_core.c:376 vlan_vid_del+0x1b8/0x1f0
CPU: 1 PID: 329 Comm: bash Tainted: G W 6.5.0-rc3+ #771
pc : vlan_vid_del+0x1b8/0x1f0
lr : vlan_vid_del+0x1b8/0x1f0
dsa_tag_8021q_unregister+0x8c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
DSA: tree 0 torn down
This was somewhat not so easy to spot, because "ocelot-8021q" is not the
default tagging protocol, and thus, not everyone who tests the unbinding
path may have switched to it beforehand. The default
felix_tag_npi_teardown() does not require rtnl_lock() to be held. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: think-lmi: Fix memory leak when showing current settings
When retriving a item string with tlmi_setting(), the result has to be
freed using kfree(). In current_value_show() however, malformed
item strings are not freed, causing a memory leak.
Fix this by eliminating the early return responsible for this. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: mediatek: mt8186: Fix use-after-free in driver remove path
When devm runs function in the "remove" path for a device it runs them
in the reverse order. That means that if you have parts of your driver
that aren't using devm or are using "roll your own" devm w/
devm_add_action_or_reset() you need to keep that in mind.
The mt8186 audio driver didn't quite get this right. Specifically, in
mt8186_init_clock() it called mt8186_audsys_clk_register() and then
went on to call a bunch of other devm function. The caller of
mt8186_init_clock() used devm_add_action_or_reset() to call
mt8186_deinit_clock() but, because of the intervening devm functions,
the order was wrong.
Specifically at probe time, the order was:
1. mt8186_audsys_clk_register()
2. afe_priv->clk = devm_kcalloc(...)
3. afe_priv->clk[i] = devm_clk_get(...)
At remove time, the order (which should have been 3, 2, 1) was:
1. mt8186_audsys_clk_unregister()
3. Free all of afe_priv->clk[i]
2. Free afe_priv->clk
The above seemed to be causing a use-after-free. Luckily, it's easy to
fix this by simply using devm more correctly. Let's move the
devm_add_action_or_reset() to the right place. In addition to fixing
the use-after-free, code inspection shows that this fixes a leak
(missing call to mt8186_audsys_clk_unregister()) that would have
happened if any of the syscon_regmap_lookup_by_phandle() calls in
mt8186_init_clock() had failed. |
