| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: cdc_eem: fix tx fixup skb leak
when usbnet transmit a skb, eem fixup it in eem_tx_fixup(),
if skb_copy_expand() failed, it return NULL,
usbnet_start_xmit() will have no chance to free original skb.
fix it by free orginal skb in eem_tx_fixup() first,
then check skb clone status, if failed, return NULL to usbnet. |
| In the Linux kernel, the following vulnerability has been resolved:
phy: phy-mtk-tphy: Fix some resource leaks in mtk_phy_init()
Use clk_disable_unprepare() in the error path of mtk_phy_init() to fix
some resource leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
can: mcba_usb: fix memory leak in mcba_usb
Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.
In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.
Fail log:
| [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected
| [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem)
So, all allocated buffers should be freed with usb_free_coherent()
explicitly
NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c |
| In the Linux kernel, the following vulnerability has been resolved:
x86/fpu: Invalidate FPU state after a failed XRSTOR from a user buffer
Both Intel and AMD consider it to be architecturally valid for XRSTOR to
fail with #PF but nonetheless change the register state. The actual
conditions under which this might occur are unclear [1], but it seems
plausible that this might be triggered if one sibling thread unmaps a page
and invalidates the shared TLB while another sibling thread is executing
XRSTOR on the page in question.
__fpu__restore_sig() can execute XRSTOR while the hardware registers
are preserved on behalf of a different victim task (using the
fpu_fpregs_owner_ctx mechanism), and, in theory, XRSTOR could fail but
modify the registers.
If this happens, then there is a window in which __fpu__restore_sig()
could schedule out and the victim task could schedule back in without
reloading its own FPU registers. This would result in part of the FPU
state that __fpu__restore_sig() was attempting to load leaking into the
victim task's user-visible state.
Invalidate preserved FPU registers on XRSTOR failure to prevent this
situation from corrupting any state.
[1] Frequent readers of the errata lists might imagine "complex
microarchitectural conditions". |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: advansys: Fix kernel pointer leak
Pointers should be printed with %p or %px rather than cast to 'unsigned
long' and printed with %lx.
Change %lx to %p to print the hashed pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: CT, Fix multiple allocations and memleak of mod acts
CT clear action offload adds additional mod hdr actions to the
flow's original mod actions in order to clear the registers which
hold ct_state.
When such flow also includes encap action, a neigh update event
can cause the driver to unoffload the flow and then reoffload it.
Each time this happens, the ct clear handling adds that same set
of mod hdr actions to reset ct_state until the max of mod hdr
actions is reached.
Also the driver never releases the allocated mod hdr actions and
causing a memleak.
Fix above two issues by moving CT clear mod acts allocation
into the parsing actions phase and only use it when offloading the rule.
The release of mod acts will be done in the normal flow_put().
backtrace:
[<000000007316e2f3>] krealloc+0x83/0xd0
[<00000000ef157de1>] mlx5e_mod_hdr_alloc+0x147/0x300 [mlx5_core]
[<00000000970ce4ae>] mlx5e_tc_match_to_reg_set_and_get_id+0xd7/0x240 [mlx5_core]
[<0000000067c5fa17>] mlx5e_tc_match_to_reg_set+0xa/0x20 [mlx5_core]
[<00000000d032eb98>] mlx5_tc_ct_entry_set_registers.isra.0+0x36/0xc0 [mlx5_core]
[<00000000fd23b869>] mlx5_tc_ct_flow_offload+0x272/0x1f10 [mlx5_core]
[<000000004fc24acc>] mlx5e_tc_offload_fdb_rules.part.0+0x150/0x620 [mlx5_core]
[<00000000dc741c17>] mlx5e_tc_encap_flows_add+0x489/0x690 [mlx5_core]
[<00000000e92e49d7>] mlx5e_rep_update_flows+0x6e4/0x9b0 [mlx5_core]
[<00000000f60f5602>] mlx5e_rep_neigh_update+0x39a/0x5d0 [mlx5_core] |
| In the Linux kernel, the following vulnerability has been resolved:
misc/uss720: fix memory leak in uss720_probe
uss720_probe forgets to decrease the refcount of usbdev in uss720_probe.
Fix this by decreasing the refcount of usbdev by usb_put_dev.
BUG: memory leak
unreferenced object 0xffff888101113800 (size 2048):
comm "kworker/0:1", pid 7, jiffies 4294956777 (age 28.870s)
hex dump (first 32 bytes):
ff ff ff ff 31 00 00 00 00 00 00 00 00 00 00 00 ....1...........
00 00 00 00 00 00 00 00 00 00 00 00 03 00 00 00 ................
backtrace:
[<ffffffff82b8e822>] kmalloc include/linux/slab.h:554 [inline]
[<ffffffff82b8e822>] kzalloc include/linux/slab.h:684 [inline]
[<ffffffff82b8e822>] usb_alloc_dev+0x32/0x450 drivers/usb/core/usb.c:582
[<ffffffff82b98441>] hub_port_connect drivers/usb/core/hub.c:5129 [inline]
[<ffffffff82b98441>] hub_port_connect_change drivers/usb/core/hub.c:5363 [inline]
[<ffffffff82b98441>] port_event drivers/usb/core/hub.c:5509 [inline]
[<ffffffff82b98441>] hub_event+0x1171/0x20c0 drivers/usb/core/hub.c:5591
[<ffffffff81259229>] process_one_work+0x2c9/0x600 kernel/workqueue.c:2275
[<ffffffff81259b19>] worker_thread+0x59/0x5d0 kernel/workqueue.c:2421
[<ffffffff81261228>] kthread+0x178/0x1b0 kernel/kthread.c:292
[<ffffffff8100227f>] ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:294 |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: fix memory leak in smsc75xx_bind
Syzbot reported memory leak in smsc75xx_bind().
The problem was is non-freed memory in case of
errors after memory allocation.
backtrace:
[<ffffffff84245b62>] kmalloc include/linux/slab.h:556 [inline]
[<ffffffff84245b62>] kzalloc include/linux/slab.h:686 [inline]
[<ffffffff84245b62>] smsc75xx_bind+0x7a/0x334 drivers/net/usb/smsc75xx.c:1460
[<ffffffff82b5b2e6>] usbnet_probe+0x3b6/0xc30 drivers/net/usb/usbnet.c:1728 |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-fsl-dspi: Fix a resource leak in an error handling path
'dspi_request_dma()' should be undone by a 'dspi_release_dma()' call in the
error handling path of the probe function, as already done in the remove
function |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: mt7530: fix VLAN traffic leaks
PCR_MATRIX field was set to all 1's when VLAN filtering is enabled, but
was not reset when it is disabled, which may cause traffic leaks:
ip link add br0 type bridge vlan_filtering 1
ip link add br1 type bridge vlan_filtering 1
ip link set swp0 master br0
ip link set swp1 master br1
ip link set br0 type bridge vlan_filtering 0
ip link set br1 type bridge vlan_filtering 0
# traffic in br0 and br1 will start leaking to each other
As port_bridge_{add,del} have set up PCR_MATRIX properly, remove the
PCR_MATRIX write from mt7530_port_set_vlan_aware. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: sja1105: add error handling in sja1105_setup()
If any of sja1105_static_config_load(), sja1105_clocking_setup() or
sja1105_devlink_setup() fails, we can't just return in the middle of
sja1105_setup() or memory will leak. Add a cleanup path. |
| In the Linux kernel, the following vulnerability has been resolved:
interconnect: qcom: bcm-voter: add a missing of_node_put()
Add a missing of_node_put() in of_bcm_voter_get() to avoid the
reference leak. |
| In the Linux kernel, the following vulnerability has been resolved:
net: fec: fix the potential memory leak in fec_enet_init()
If the memory allocated for cbd_base is failed, it should
free the memory allocated for the queues, otherwise it causes
memory leak.
And if the memory allocated for the queues is failed, it can
return error directly. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: amd_sfh: Fix memory leak in amd_sfh_work
Kmemleak tool detected a memory leak in the amd_sfh driver.
====================
unreferenced object 0xffff88810228ada0 (size 32):
comm "insmod", pid 3968, jiffies 4295056001 (age 775.792s)
hex dump (first 32 bytes):
00 20 73 1f 81 88 ff ff 00 01 00 00 00 00 ad de . s.............
22 01 00 00 00 00 ad de 01 00 02 00 00 00 00 00 "...............
backtrace:
[<000000007b4c8799>] kmem_cache_alloc_trace+0x163/0x4f0
[<0000000005326893>] amd_sfh_get_report+0xa4/0x1d0 [amd_sfh]
[<000000002a9e5ec4>] amdtp_hid_request+0x62/0x80 [amd_sfh]
[<00000000b8a95807>] sensor_hub_get_feature+0x145/0x270 [hid_sensor_hub]
[<00000000fda054ee>] hid_sensor_parse_common_attributes+0x215/0x460 [hid_sensor_iio_common]
[<0000000021279ecf>] hid_accel_3d_probe+0xff/0x4a0 [hid_sensor_accel_3d]
[<00000000915760ce>] platform_probe+0x6a/0xd0
[<0000000060258a1f>] really_probe+0x192/0x620
[<00000000fa812f2d>] driver_probe_device+0x14a/0x1d0
[<000000005e79f7fd>] __device_attach_driver+0xbd/0x110
[<0000000070d15018>] bus_for_each_drv+0xfd/0x160
[<0000000013a3c312>] __device_attach+0x18b/0x220
[<000000008c7b4afc>] device_initial_probe+0x13/0x20
[<00000000e6e99665>] bus_probe_device+0xfe/0x120
[<00000000833fa90b>] device_add+0x6a6/0xe00
[<00000000fa901078>] platform_device_add+0x180/0x380
====================
The fix is to freeing request_list entry once the processed entry is
removed from the request_list. |
| In the Linux kernel, the following vulnerability has been resolved:
sch_htb: fix refcount leak in htb_parent_to_leaf_offload
The commit ae81feb7338c ("sch_htb: fix null pointer dereference
on a null new_q") fixes a NULL pointer dereference bug, but it
is not correct.
Because htb_graft_helper properly handles the case when new_q
is NULL, and after the previous patch by skipping this call
which creates an inconsistency : dev_queue->qdisc will still
point to the old qdisc, but cl->parent->leaf.q will point to
the new one (which will be noop_qdisc, because new_q was NULL).
The code is based on an assumption that these two pointers are
the same, so it can lead to refcount leaks.
The correct fix is to add a NULL pointer check to protect
qdisc_refcount_inc inside htb_parent_to_leaf_offload. |
| In the Linux kernel, the following vulnerability has been resolved:
net: caif: fix memory leak in caif_device_notify
In case of caif_enroll_dev() fail, allocated
link_support won't be assigned to the corresponding
structure. So simply free allocated pointer in case
of error |
| In the Linux kernel, the following vulnerability has been resolved:
net: caif: fix memory leak in cfusbl_device_notify
In case of caif_enroll_dev() fail, allocated
link_support won't be assigned to the corresponding
structure. So simply free allocated pointer in case
of error. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix memory leak in ext4_fill_super
Buffer head references must be released before calling kill_bdev();
otherwise the buffer head (and its page referenced by b_data) will not
be freed by kill_bdev, and subsequently that bh will be leaked.
If blocksizes differ, sb_set_blocksize() will kill current buffers and
page cache by using kill_bdev(). And then super block will be reread
again but using correct blocksize this time. sb_set_blocksize() didn't
fully free superblock page and buffer head, and being busy, they were
not freed and instead leaked.
This can easily be reproduced by calling an infinite loop of:
systemctl start <ext4_on_lvm>.mount, and
systemctl stop <ext4_on_lvm>.mount
... since systemd creates a cgroup for each slice which it mounts, and
the bh leak get amplified by a dying memory cgroup that also never
gets freed, and memory consumption is much more easily noticed. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix memory leak in ext4_mb_init_backend on error path.
Fix a memory leak discovered by syzbot when a file system is corrupted
with an illegally large s_log_groups_per_flex. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: xsk: return xsk buffers back to pool when cleaning the ring
Currently we only NULL the xdp_buff pointer in the internal SW ring but
we never give it back to the xsk buffer pool. This means that buffers
can be leaked out of the buff pool and never be used again.
Add missing xsk_buff_free() call to the routine that is supposed to
clean the entries that are left in the ring so that these buffers in the
umem can be used by other sockets.
Also, only go through the space that is actually left to be cleaned
instead of a whole ring. |
