| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: dlink: handle copy_thresh allocation failure
The driver did not handle failure of `netdev_alloc_skb_ip_align()`.
If the allocation failed, dereferencing `skb->protocol` could lead to
a NULL pointer dereference.
This patch tries to allocate `skb`. If the allocation fails, it falls
back to the normal path.
Tested-on: D-Link DGE-550T Rev-A3 |
| In the Linux kernel, the following vulnerability has been resolved:
Squashfs: fix uninit-value in squashfs_get_parent
Syzkaller reports a "KMSAN: uninit-value in squashfs_get_parent" bug.
This is caused by open_by_handle_at() being called with a file handle
containing an invalid parent inode number. In particular the inode number
is that of a symbolic link, rather than a directory.
Squashfs_get_parent() gets called with that symbolic link inode, and
accesses the parent member field.
unsigned int parent_ino = squashfs_i(inode)->parent;
Because non-directory inodes in Squashfs do not have a parent value, this
is uninitialised, and this causes an uninitialised value access.
The fix is to initialise parent with the invalid inode 0, which will cause
an EINVAL error to be returned.
Regular inodes used to share the parent field with the block_list_start
field. This is removed in this commit to enable the parent field to
contain the invalid inode number 0. |
| In the Linux kernel, the following vulnerability has been resolved:
uio_hv_generic: Let userspace take care of interrupt mask
Remove the logic to set interrupt mask by default in uio_hv_generic
driver as the interrupt mask value is supposed to be controlled
completely by the user space. If the mask bit gets changed
by the driver, concurrently with user mode operating on the ring,
the mask bit may be set when it is supposed to be clear, and the
user-mode driver will miss an interrupt which will cause a hang.
For eg- when the driver sets inbound ring buffer interrupt mask to 1,
the host does not interrupt the guest on the UIO VMBus channel.
However, setting the mask does not prevent the host from putting a
message in the inbound ring buffer. So let’s assume that happens,
the host puts a message into the ring buffer but does not interrupt.
Subsequently, the user space code in the guest sets the inbound ring
buffer interrupt mask to 0, saying “Hey, I’m ready for interrupts”.
User space code then calls pread() to wait for an interrupt.
Then one of two things happens:
* The host never sends another message. So the pread() waits forever.
* The host does send another message. But because there’s already a
message in the ring buffer, it doesn’t generate an interrupt.
This is the correct behavior, because the host should only send an
interrupt when the inbound ring buffer transitions from empty to
not-empty. Adding an additional message to a ring buffer that is not
empty is not supposed to generate an interrupt on the guest.
Since the guest is waiting in pread() and not removing messages from
the ring buffer, the pread() waits forever.
This could be easily reproduced in hv_fcopy_uio_daemon if we delay
setting interrupt mask to 0.
Similarly if hv_uio_channel_cb() sets the interrupt_mask to 1,
there’s a race condition. Once user space empties the inbound ring
buffer, but before user space sets interrupt_mask to 0, the host could
put another message in the ring buffer but it wouldn’t interrupt.
Then the next pread() would hang.
Fix these by removing all instances where interrupt_mask is changed,
while keeping the one in set_event() unchanged to enable userspace
control the interrupt mask by writing 0/1 to /dev/uioX. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: udf: fix OOB read in lengthAllocDescs handling
When parsing Allocation Extent Descriptor, lengthAllocDescs comes from
on-disk data and must be validated against the block size. Crafted or
corrupted images may set lengthAllocDescs so that the total descriptor
length (sizeof(allocExtDesc) + lengthAllocDescs) exceeds the buffer,
leading udf_update_tag() to call crc_itu_t() on out-of-bounds memory and
trigger a KASAN use-after-free read.
BUG: KASAN: use-after-free in crc_itu_t+0x1d5/0x2b0 lib/crc-itu-t.c:60
Read of size 1 at addr ffff888041e7d000 by task syz-executor317/5309
CPU: 0 UID: 0 PID: 5309 Comm: syz-executor317 Not tainted 6.12.0-rc4-syzkaller-00261-g850925a8133c #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:377 [inline]
print_report+0x169/0x550 mm/kasan/report.c:488
kasan_report+0x143/0x180 mm/kasan/report.c:601
crc_itu_t+0x1d5/0x2b0 lib/crc-itu-t.c:60
udf_update_tag+0x70/0x6a0 fs/udf/misc.c:261
udf_write_aext+0x4d8/0x7b0 fs/udf/inode.c:2179
extent_trunc+0x2f7/0x4a0 fs/udf/truncate.c:46
udf_truncate_tail_extent+0x527/0x7e0 fs/udf/truncate.c:106
udf_release_file+0xc1/0x120 fs/udf/file.c:185
__fput+0x23f/0x880 fs/file_table.c:431
task_work_run+0x24f/0x310 kernel/task_work.c:239
exit_task_work include/linux/task_work.h:43 [inline]
do_exit+0xa2f/0x28e0 kernel/exit.c:939
do_group_exit+0x207/0x2c0 kernel/exit.c:1088
__do_sys_exit_group kernel/exit.c:1099 [inline]
__se_sys_exit_group kernel/exit.c:1097 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1097
x64_sys_call+0x2634/0x2640 arch/x86/include/generated/asm/syscalls_64.h:232
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
</TASK>
Validate the computed total length against epos->bh->b_size.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix race condition in kprobe initialization causing NULL pointer dereference
There is a critical race condition in kprobe initialization that can lead to
NULL pointer dereference and kernel crash.
[1135630.084782] Unable to handle kernel paging request at virtual address 0000710a04630000
...
[1135630.260314] pstate: 404003c9 (nZcv DAIF +PAN -UAO)
[1135630.269239] pc : kprobe_perf_func+0x30/0x260
[1135630.277643] lr : kprobe_dispatcher+0x44/0x60
[1135630.286041] sp : ffffaeff4977fa40
[1135630.293441] x29: ffffaeff4977fa40 x28: ffffaf015340e400
[1135630.302837] x27: 0000000000000000 x26: 0000000000000000
[1135630.312257] x25: ffffaf029ed108a8 x24: ffffaf015340e528
[1135630.321705] x23: ffffaeff4977fc50 x22: ffffaeff4977fc50
[1135630.331154] x21: 0000000000000000 x20: ffffaeff4977fc50
[1135630.340586] x19: ffffaf015340e400 x18: 0000000000000000
[1135630.349985] x17: 0000000000000000 x16: 0000000000000000
[1135630.359285] x15: 0000000000000000 x14: 0000000000000000
[1135630.368445] x13: 0000000000000000 x12: 0000000000000000
[1135630.377473] x11: 0000000000000000 x10: 0000000000000000
[1135630.386411] x9 : 0000000000000000 x8 : 0000000000000000
[1135630.395252] x7 : 0000000000000000 x6 : 0000000000000000
[1135630.403963] x5 : 0000000000000000 x4 : 0000000000000000
[1135630.412545] x3 : 0000710a04630000 x2 : 0000000000000006
[1135630.421021] x1 : ffffaeff4977fc50 x0 : 0000710a04630000
[1135630.429410] Call trace:
[1135630.434828] kprobe_perf_func+0x30/0x260
[1135630.441661] kprobe_dispatcher+0x44/0x60
[1135630.448396] aggr_pre_handler+0x70/0xc8
[1135630.454959] kprobe_breakpoint_handler+0x140/0x1e0
[1135630.462435] brk_handler+0xbc/0xd8
[1135630.468437] do_debug_exception+0x84/0x138
[1135630.475074] el1_dbg+0x18/0x8c
[1135630.480582] security_file_permission+0x0/0xd0
[1135630.487426] vfs_write+0x70/0x1c0
[1135630.493059] ksys_write+0x5c/0xc8
[1135630.498638] __arm64_sys_write+0x24/0x30
[1135630.504821] el0_svc_common+0x78/0x130
[1135630.510838] el0_svc_handler+0x38/0x78
[1135630.516834] el0_svc+0x8/0x1b0
kernel/trace/trace_kprobe.c: 1308
0xffff3df8995039ec <kprobe_perf_func+0x2c>: ldr x21, [x24,#120]
include/linux/compiler.h: 294
0xffff3df8995039f0 <kprobe_perf_func+0x30>: ldr x1, [x21,x0]
kernel/trace/trace_kprobe.c
1308: head = this_cpu_ptr(call->perf_events);
1309: if (hlist_empty(head))
1310: return 0;
crash> struct trace_event_call -o
struct trace_event_call {
...
[120] struct hlist_head *perf_events; //(call->perf_event)
...
}
crash> struct trace_event_call ffffaf015340e528
struct trace_event_call {
...
perf_events = 0xffff0ad5fa89f088, //this value is correct, but x21 = 0
...
}
Race Condition Analysis:
The race occurs between kprobe activation and perf_events initialization:
CPU0 CPU1
==== ====
perf_kprobe_init
perf_trace_event_init
tp_event->perf_events = list;(1)
tp_event->class->reg (2)← KPROBE ACTIVE
Debug exception triggers
...
kprobe_dispatcher
kprobe_perf_func (tk->tp.flags & TP_FLAG_PROFILE)
head = this_cpu_ptr(call->perf_events)(3)
(perf_events is still NULL)
Problem:
1. CPU0 executes (1) assigning tp_event->perf_events = list
2. CPU0 executes (2) enabling kprobe functionality via class->reg()
3. CPU1 triggers and reaches kprobe_dispatcher
4. CPU1 checks TP_FLAG_PROFILE - condition passes (step 2 completed)
5. CPU1 calls kprobe_perf_func() and crashes at (3) because
call->perf_events is still NULL
CPU1 sees that kprobe functionality is enabled but does not see that
perf_events has been assigned.
Add pairing read an
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
mm/ksm: fix flag-dropping behavior in ksm_madvise
syzkaller discovered the following crash: (kernel BUG)
[ 44.607039] ------------[ cut here ]------------
[ 44.607422] kernel BUG at mm/userfaultfd.c:2067!
[ 44.608148] Oops: invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN NOPTI
[ 44.608814] CPU: 1 UID: 0 PID: 2475 Comm: reproducer Not tainted 6.16.0-rc6 #1 PREEMPT(none)
[ 44.609635] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[ 44.610695] RIP: 0010:userfaultfd_release_all+0x3a8/0x460
<snip other registers, drop unreliable trace>
[ 44.617726] Call Trace:
[ 44.617926] <TASK>
[ 44.619284] userfaultfd_release+0xef/0x1b0
[ 44.620976] __fput+0x3f9/0xb60
[ 44.621240] fput_close_sync+0x110/0x210
[ 44.622222] __x64_sys_close+0x8f/0x120
[ 44.622530] do_syscall_64+0x5b/0x2f0
[ 44.622840] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 44.623244] RIP: 0033:0x7f365bb3f227
Kernel panics because it detects UFFD inconsistency during
userfaultfd_release_all(). Specifically, a VMA which has a valid pointer
to vma->vm_userfaultfd_ctx, but no UFFD flags in vma->vm_flags.
The inconsistency is caused in ksm_madvise(): when user calls madvise()
with MADV_UNMEARGEABLE on a VMA that is registered for UFFD in MINOR mode,
it accidentally clears all flags stored in the upper 32 bits of
vma->vm_flags.
Assuming x86_64 kernel build, unsigned long is 64-bit and unsigned int and
int are 32-bit wide. This setup causes the following mishap during the &=
~VM_MERGEABLE assignment.
VM_MERGEABLE is a 32-bit constant of type unsigned int, 0x8000'0000.
After ~ is applied, it becomes 0x7fff'ffff unsigned int, which is then
promoted to unsigned long before the & operation. This promotion fills
upper 32 bits with leading 0s, as we're doing unsigned conversion (and
even for a signed conversion, this wouldn't help as the leading bit is 0).
& operation thus ends up AND-ing vm_flags with 0x0000'0000'7fff'ffff
instead of intended 0xffff'ffff'7fff'ffff and hence accidentally clears
the upper 32-bits of its value.
Fix it by changing `VM_MERGEABLE` constant to unsigned long, using the
BIT() macro.
Note: other VM_* flags are not affected: This only happens to the
VM_MERGEABLE flag, as the other VM_* flags are all constants of type int
and after ~ operation, they end up with leading 1 and are thus converted
to unsigned long with leading 1s.
Note 2:
After commit 31defc3b01d9 ("userfaultfd: remove (VM_)BUG_ON()s"), this is
no longer a kernel BUG, but a WARNING at the same place:
[ 45.595973] WARNING: CPU: 1 PID: 2474 at mm/userfaultfd.c:2067
but the root-cause (flag-drop) remains the same.
[akpm@linux-foundation.org: rust bindgen wasn't able to handle BIT(), from Miguel] |
| In the Linux kernel, the following vulnerability has been resolved:
Input: uinput - zero-initialize uinput_ff_upload_compat to avoid info leak
Struct ff_effect_compat is embedded twice inside
uinput_ff_upload_compat, contains internal padding. In particular, there
is a hole after struct ff_replay to satisfy alignment requirements for
the following union member. Without clearing the structure,
copy_to_user() may leak stack data to userspace.
Initialize ff_up_compat to zero before filling valid fields. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: check the return value of pinmux_ops::get_function_name()
While the API contract in docs doesn't specify it explicitly, the
generic implementation of the get_function_name() callback from struct
pinmux_ops - pinmux_generic_get_function_name() - can fail and return
NULL. This is already checked in pinmux_check_ops() so add a similar
check in pinmux_func_name_to_selector() instead of passing the returned
pointer right down to strcmp() where the NULL can get dereferenced. This
is normal operation when adding new pinfunctions. |
| In the Linux kernel, the following vulnerability has been resolved:
bus: fsl-mc: Check return value of platform_get_resource()
platform_get_resource() returns NULL in case of failure, so check its
return value and propagate the error in order to prevent NULL pointer
dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
net/9p: fix double req put in p9_fd_cancelled
Syzkaller reports a KASAN issue as below:
general protection fault, probably for non-canonical address 0xfbd59c0000000021: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: maybe wild-memory-access in range [0xdead000000000108-0xdead00000000010f]
CPU: 0 PID: 5083 Comm: syz-executor.2 Not tainted 6.1.134-syzkaller-00037-g855bd1d7d838 #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
RIP: 0010:__list_del include/linux/list.h:114 [inline]
RIP: 0010:__list_del_entry include/linux/list.h:137 [inline]
RIP: 0010:list_del include/linux/list.h:148 [inline]
RIP: 0010:p9_fd_cancelled+0xe9/0x200 net/9p/trans_fd.c:734
Call Trace:
<TASK>
p9_client_flush+0x351/0x440 net/9p/client.c:614
p9_client_rpc+0xb6b/0xc70 net/9p/client.c:734
p9_client_version net/9p/client.c:920 [inline]
p9_client_create+0xb51/0x1240 net/9p/client.c:1027
v9fs_session_init+0x1f0/0x18f0 fs/9p/v9fs.c:408
v9fs_mount+0xba/0xcb0 fs/9p/vfs_super.c:126
legacy_get_tree+0x108/0x220 fs/fs_context.c:632
vfs_get_tree+0x8e/0x300 fs/super.c:1573
do_new_mount fs/namespace.c:3056 [inline]
path_mount+0x6a6/0x1e90 fs/namespace.c:3386
do_mount fs/namespace.c:3399 [inline]
__do_sys_mount fs/namespace.c:3607 [inline]
__se_sys_mount fs/namespace.c:3584 [inline]
__x64_sys_mount+0x283/0x300 fs/namespace.c:3584
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x35/0x80 arch/x86/entry/common.c:81
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
This happens because of a race condition between:
- The 9p client sending an invalid flush request and later cleaning it up;
- The 9p client in p9_read_work() canceled all pending requests.
Thread 1 Thread 2
...
p9_client_create()
...
p9_fd_create()
...
p9_conn_create()
...
// start Thread 2
INIT_WORK(&m->rq, p9_read_work);
p9_read_work()
...
p9_client_rpc()
...
...
p9_conn_cancel()
...
spin_lock(&m->req_lock);
...
p9_fd_cancelled()
...
...
spin_unlock(&m->req_lock);
// status rewrite
p9_client_cb(m->client, req, REQ_STATUS_ERROR)
// first remove
list_del(&req->req_list);
...
spin_lock(&m->req_lock)
...
// second remove
list_del(&req->req_list);
spin_unlock(&m->req_lock)
...
Commit 74d6a5d56629 ("9p/trans_fd: Fix concurrency del of req_list in
p9_fd_cancelled/p9_read_work") fixes a concurrency issue in the 9p filesystem
client where the req_list could be deleted simultaneously by both
p9_read_work and p9_fd_cancelled functions, but for the case where req->status
equals REQ_STATUS_RCVD.
Update the check for req->status in p9_fd_cancelled to skip processing not
just received requests, but anything that is not SENT, as whatever
changed the state from SENT also removed the request from its list.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
[updated the check from status == RECV || status == ERROR to status != SENT] |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Don't (re)check L1 intercepts when completing userspace I/O
When completing emulation of instruction that generated a userspace exit
for I/O, don't recheck L1 intercepts as KVM has already finished that
phase of instruction execution, i.e. has already committed to allowing L2
to perform I/O. If L1 (or host userspace) modifies the I/O permission
bitmaps during the exit to userspace, KVM will treat the access as being
intercepted despite already having emulated the I/O access.
Pivot on EMULTYPE_NO_DECODE to detect that KVM is completing emulation.
Of the three users of EMULTYPE_NO_DECODE, only complete_emulated_io() (the
intended "recipient") can reach the code in question. gp_interception()'s
use is mutually exclusive with is_guest_mode(), and
complete_emulated_insn_gp() unconditionally pairs EMULTYPE_NO_DECODE with
EMULTYPE_SKIP.
The bad behavior was detected by a syzkaller program that toggles port I/O
interception during the userspace I/O exit, ultimately resulting in a WARN
on vcpu->arch.pio.count being non-zero due to KVM no completing emulation
of the I/O instruction.
WARNING: CPU: 23 PID: 1083 at arch/x86/kvm/x86.c:8039 emulator_pio_in_out+0x154/0x170 [kvm]
Modules linked in: kvm_intel kvm irqbypass
CPU: 23 UID: 1000 PID: 1083 Comm: repro Not tainted 6.16.0-rc5-c1610d2d66b1-next-vm #74 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:emulator_pio_in_out+0x154/0x170 [kvm]
PKRU: 55555554
Call Trace:
<TASK>
kvm_fast_pio+0xd6/0x1d0 [kvm]
vmx_handle_exit+0x149/0x610 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0xda8/0x1ac0 [kvm]
kvm_vcpu_ioctl+0x244/0x8c0 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0x5d/0xc60
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: essiv - Check ssize for decryption and in-place encryption
Move the ssize check to the start in essiv_aead_crypt so that
it's also checked for decryption and in-place encryption. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: Defer ip_vs_ftp unregister during netns cleanup
On the netns cleanup path, __ip_vs_ftp_exit() may unregister ip_vs_ftp
before connections with valid cp->app pointers are flushed, leading to a
use-after-free.
Fix this by introducing a global `exiting_module` flag, set to true in
ip_vs_ftp_exit() before unregistering the pernet subsystem. In
__ip_vs_ftp_exit(), skip ip_vs_ftp unregister if called during netns
cleanup (when exiting_module is false) and defer it to
__ip_vs_cleanup_batch(), which unregisters all apps after all connections
are flushed. If called during module exit, unregister ip_vs_ftp
immediately. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mvsas: Fix use-after-free bugs in mvs_work_queue
During the detaching of Marvell's SAS/SATA controller, the original code
calls cancel_delayed_work() in mvs_free() to cancel the delayed work
item mwq->work_q. However, if mwq->work_q is already running, the
cancel_delayed_work() may fail to cancel it. This can lead to
use-after-free scenarios where mvs_free() frees the mvs_info while
mvs_work_queue() is still executing and attempts to access the
already-freed mvs_info.
A typical race condition is illustrated below:
CPU 0 (remove) | CPU 1 (delayed work callback)
mvs_pci_remove() |
mvs_free() | mvs_work_queue()
cancel_delayed_work() |
kfree(mvi) |
| mvi-> // UAF
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the delayed work item is properly canceled and any executing
delayed work item completes before the mvs_info is deallocated.
This bug was found by static analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: target_core_configfs: Add length check to avoid buffer overflow
A buffer overflow arises from the usage of snprintf to write into the
buffer "buf" in target_lu_gp_members_show function located in
/drivers/target/target_core_configfs.c. This buffer is allocated with
size LU_GROUP_NAME_BUF (256 bytes).
snprintf(...) formats multiple strings into buf with the HBA name
(hba->hba_group.cg_item), a slash character, a devicename (dev->
dev_group.cg_item) and a newline character, the total formatted string
length may exceed the buffer size of 256 bytes.
Since snprintf() returns the total number of bytes that would have been
written (the length of %s/%sn ), this value may exceed the buffer length
(256 bytes) passed to memcpy(), this will ultimately cause function
memcpy reporting a buffer overflow error.
An additional check of the return value of snprintf() can avoid this
buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
media: b2c2: Fix use-after-free causing by irq_check_work in flexcop_pci_remove
The original code uses cancel_delayed_work() in flexcop_pci_remove(), which
does not guarantee that the delayed work item irq_check_work has fully
completed if it was already running. This leads to use-after-free scenarios
where flexcop_pci_remove() may free the flexcop_device while irq_check_work
is still active and attempts to dereference the device.
A typical race condition is illustrated below:
CPU 0 (remove) | CPU 1 (delayed work callback)
flexcop_pci_remove() | flexcop_pci_irq_check_work()
cancel_delayed_work() |
flexcop_device_kfree(fc_pci->fc_dev) |
| fc = fc_pci->fc_dev; // UAF
This is confirmed by a KASAN report:
==================================================================
BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0
Write of size 8 at addr ffff8880093aa8c8 by task bash/135
...
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_report+0xcf/0x610
? __run_timer_base.part.0+0x7d7/0x8c0
kasan_report+0xb8/0xf0
? __run_timer_base.part.0+0x7d7/0x8c0
__run_timer_base.part.0+0x7d7/0x8c0
? __pfx___run_timer_base.part.0+0x10/0x10
? __pfx_read_tsc+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
run_timer_softirq+0xd1/0x190
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
Allocated by task 1:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
__kmalloc_noprof+0x1be/0x460
flexcop_device_kmalloc+0x54/0xe0
flexcop_pci_probe+0x1f/0x9d0
local_pci_probe+0xdc/0x190
pci_device_probe+0x2fe/0x470
really_probe+0x1ca/0x5c0
__driver_probe_device+0x248/0x310
driver_probe_device+0x44/0x120
__driver_attach+0xd2/0x310
bus_for_each_dev+0xed/0x170
bus_add_driver+0x208/0x500
driver_register+0x132/0x460
do_one_initcall+0x89/0x300
kernel_init_freeable+0x40d/0x720
kernel_init+0x1a/0x150
ret_from_fork+0x10c/0x1a0
ret_from_fork_asm+0x1a/0x30
Freed by task 135:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3a/0x60
__kasan_slab_free+0x3f/0x50
kfree+0x137/0x370
flexcop_device_kfree+0x32/0x50
pci_device_remove+0xa6/0x1d0
device_release_driver_internal+0xf8/0x210
pci_stop_bus_device+0x105/0x150
pci_stop_and_remove_bus_device_locked+0x15/0x30
remove_store+0xcc/0xe0
kernfs_fop_write_iter+0x2c3/0x440
vfs_write+0x871/0xd70
ksys_write+0xee/0x1c0
do_syscall_64+0xac/0x280
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the delayed work item is properly canceled and any executing delayed
work has finished before the device memory is deallocated.
This bug was initially identified through static analysis. To reproduce
and test it, I simulated the B2C2 FlexCop PCI device in QEMU and introduced
artificial delays within the flexcop_pci_irq_check_work() function to
increase the likelihood of triggering the bug. |
| In the Linux kernel, the following vulnerability has been resolved:
media: i2c: tc358743: Fix use-after-free bugs caused by orphan timer in probe
The state->timer is a cyclic timer that schedules work_i2c_poll and
delayed_work_enable_hotplug, while rearming itself. Using timer_delete()
fails to guarantee the timer isn't still running when destroyed, similarly
cancel_delayed_work() cannot ensure delayed_work_enable_hotplug has
terminated if already executing. During probe failure after timer
initialization, these may continue running as orphans and reference the
already-freed tc358743_state object through tc358743_irq_poll_timer.
The following is the trace captured by KASAN.
BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0
Write of size 8 at addr ffff88800ded83c8 by task swapper/1/0
...
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_report+0xcf/0x610
? __pfx_sched_balance_find_src_group+0x10/0x10
? __run_timer_base.part.0+0x7d7/0x8c0
kasan_report+0xb8/0xf0
? __run_timer_base.part.0+0x7d7/0x8c0
__run_timer_base.part.0+0x7d7/0x8c0
? rcu_sched_clock_irq+0xb06/0x27d0
? __pfx___run_timer_base.part.0+0x10/0x10
? try_to_wake_up+0xb15/0x1960
? tmigr_update_events+0x280/0x740
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
tmigr_handle_remote_up+0x603/0x7e0
? __pfx_tmigr_handle_remote_up+0x10/0x10
? sched_balance_trigger+0x98/0x9f0
? sched_tick+0x221/0x5a0
? _raw_spin_lock_irq+0x80/0xe0
? __pfx__raw_spin_lock_irq+0x10/0x10
? tick_nohz_handler+0x339/0x440
? __pfx_tmigr_handle_remote_up+0x10/0x10
__walk_groups.isra.0+0x42/0x150
tmigr_handle_remote+0x1f4/0x2e0
? __pfx_tmigr_handle_remote+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
? hrtimer_interrupt+0x322/0x780
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
Allocated by task 141:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
__kmalloc_node_track_caller_noprof+0x198/0x430
devm_kmalloc+0x7b/0x1e0
tc358743_probe+0xb7/0x610 i2c_device_probe+0x51d/0x880
really_probe+0x1ca/0x5c0
__driver_probe_device+0x248/0x310
driver_probe_device+0x44/0x120
__device_attach_driver+0x174/0x220
bus_for_each_drv+0x100/0x190
__device_attach+0x206/0x370
bus_probe_device+0x123/0x170
device_add+0xd25/0x1470
i2c_new_client_device+0x7a0/0xcd0
do_one_initcall+0x89/0x300
do_init_module+0x29d/0x7f0
load_module+0x4f48/0x69e0
init_module_from_file+0xe4/0x150
idempotent_init_module+0x320/0x670
__x64_sys_finit_module+0xbd/0x120
do_syscall_64+0xac/0x280
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 141:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3a/0x60
__kasan_slab_free+0x3f/0x50
kfree+0x137/0x370
release_nodes+0xa4/0x100
devres_release_group+0x1b2/0x380
i2c_device_probe+0x694/0x880
really_probe+0x1ca/0x5c0
__driver_probe_device+0x248/0x310
driver_probe_device+0x44/0x120
__device_attach_driver+0x174/0x220
bus_for_each_drv+0x100/0x190
__device_attach+0x206/0x370
bus_probe_device+0x123/0x170
device_add+0xd25/0x1470
i2c_new_client_device+0x7a0/0xcd0
do_one_initcall+0x89/0x300
do_init_module+0x29d/0x7f0
load_module+0x4f48/0x69e0
init_module_from_file+0xe4/0x150
idempotent_init_module+0x320/0x670
__x64_sys_finit_module+0xbd/0x120
do_syscall_64+0xac/0x280
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
Replace timer_delete() with timer_delete_sync() and cancel_delayed_work()
with cancel_delayed_work_sync() to ensure proper termination of timer and
work items before resource cleanup.
This bug was initially identified through static analysis. For reproduction
and testing, I created a functional emulation of the tc358743 device via a
kernel module and introduced faults through the debugfs interface. |
| In the Linux kernel, the following vulnerability has been resolved:
media: tuner: xc5000: Fix use-after-free in xc5000_release
The original code uses cancel_delayed_work() in xc5000_release(), which
does not guarantee that the delayed work item timer_sleep has fully
completed if it was already running. This leads to use-after-free scenarios
where xc5000_release() may free the xc5000_priv while timer_sleep is still
active and attempts to dereference the xc5000_priv.
A typical race condition is illustrated below:
CPU 0 (release thread) | CPU 1 (delayed work callback)
xc5000_release() | xc5000_do_timer_sleep()
cancel_delayed_work() |
hybrid_tuner_release_state(priv) |
kfree(priv) |
| priv = container_of() // UAF
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the timer_sleep is properly canceled before the xc5000_priv memory
is deallocated.
A deadlock concern was considered: xc5000_release() is called in a process
context and is not holding any locks that the timer_sleep work item might
also need. Therefore, the use of the _sync() variant is safe here.
This bug was initially identified through static analysis.
[hverkuil: fix typo in Subject: tunner -> tuner] |
| In the Linux kernel, the following vulnerability has been resolved:
media: rc: fix races with imon_disconnect()
Syzbot reports a KASAN issue as below:
BUG: KASAN: use-after-free in __create_pipe include/linux/usb.h:1945 [inline]
BUG: KASAN: use-after-free in send_packet+0xa2d/0xbc0 drivers/media/rc/imon.c:627
Read of size 4 at addr ffff8880256fb000 by task syz-executor314/4465
CPU: 2 PID: 4465 Comm: syz-executor314 Not tainted 6.0.0-rc1-syzkaller #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:317 [inline]
print_report.cold+0x2ba/0x6e9 mm/kasan/report.c:433
kasan_report+0xb1/0x1e0 mm/kasan/report.c:495
__create_pipe include/linux/usb.h:1945 [inline]
send_packet+0xa2d/0xbc0 drivers/media/rc/imon.c:627
vfd_write+0x2d9/0x550 drivers/media/rc/imon.c:991
vfs_write+0x2d7/0xdd0 fs/read_write.c:576
ksys_write+0x127/0x250 fs/read_write.c:631
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The iMON driver improperly releases the usb_device reference in
imon_disconnect without coordinating with active users of the
device.
Specifically, the fields usbdev_intf0 and usbdev_intf1 are not
protected by the users counter (ictx->users). During probe,
imon_init_intf0 or imon_init_intf1 increments the usb_device
reference count depending on the interface. However, during
disconnect, usb_put_dev is called unconditionally, regardless of
actual usage.
As a result, if vfd_write or other operations are still in
progress after disconnect, this can lead to a use-after-free of
the usb_device pointer.
Thread 1 vfd_write Thread 2 imon_disconnect
...
if
usb_put_dev(ictx->usbdev_intf0)
else
usb_put_dev(ictx->usbdev_intf1)
...
while
send_packet
if
pipe = usb_sndintpipe(
ictx->usbdev_intf0) UAF
else
pipe = usb_sndctrlpipe(
ictx->usbdev_intf0, 0) UAF
Guard access to usbdev_intf0 and usbdev_intf1 after disconnect by
checking ictx->disconnected in all writer paths. Add early return
with -ENODEV in send_packet(), vfd_write(), lcd_write() and
display_open() if the device is no longer present.
Set and read ictx->disconnected under ictx->lock to ensure memory
synchronization. Acquire the lock in imon_disconnect() before setting
the flag to synchronize with any ongoing operations.
Ensure writers exit early and safely after disconnect before the USB
core proceeds with cleanup.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86/amd/hsmp: Ensure sock->metric_tbl_addr is non-NULL
If metric table address is not allocated, accessing metrics_bin will
result in a NULL pointer dereference, so add a check. |
