Filtered by vendor Linux
Subscriptions
Total
6990 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2021-47369 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: s390/qeth: fix NULL deref in qeth_clear_working_pool_list() When qeth_set_online() calls qeth_clear_working_pool_list() to roll back after an error exit from qeth_hardsetup_card(), we are at risk of accessing card->qdio.in_q before it was allocated by qeth_alloc_qdio_queues() via qeth_mpc_initialize(). qeth_clear_working_pool_list() then dereferences NULL, and by writing to queue->bufs[i].pool_entry scribbles all over the CPU's lowcore. Resulting in a crash when those lowcore areas are used next (eg. on the next machine-check interrupt). Such a scenario would typically happen when the device is first set online and its queues aren't allocated yet. An early IO error or certain misconfigs (eg. mismatched transport mode, bad portno) then cause us to error out from qeth_hardsetup_card() with card->qdio.in_q still being NULL. Fix it by checking the pointer for NULL before accessing it. Note that we also have (rare) paths inside qeth_mpc_initialize() where a configuration change can cause us to free the existing queues, expecting that subsequent code will allocate them again. If we then error out before that re-allocation happens, the same bug occurs. Root-caused-by: Heiko Carstens <hca@linux.ibm.com> | ||||
| CVE-2021-47354 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 9.1 Critical |
| In the Linux kernel, the following vulnerability has been resolved: drm/sched: Avoid data corruptions Wait for all dependencies of a job to complete before killing it to avoid data corruptions. | ||||
| CVE-2021-47378 | 2 Linux, Redhat | 4 Linux Kernel, Rhel Aus, Rhel E4s and 1 more | 2024-08-04 | 9.8 Critical |
| In the Linux kernel, the following vulnerability has been resolved: nvme-rdma: destroy cm id before destroy qp to avoid use after free We should always destroy cm_id before destroy qp to avoid to get cma event after qp was destroyed, which may lead to use after free. In RDMA connection establishment error flow, don't destroy qp in cm event handler.Just report cm_error to upper level, qp will be destroy in nvme_rdma_alloc_queue() after destroy cm id. | ||||
| CVE-2021-47367 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: virtio-net: fix pages leaking when building skb in big mode We try to use build_skb() if we had sufficient tailroom. But we forget to release the unused pages chained via private in big mode which will leak pages. Fixing this by release the pages after building the skb in big mode. | ||||
| CVE-2021-47348 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 9.1 Critical |
| In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Avoid HDCP over-read and corruption Instead of reading the desired 5 bytes of the actual target field, the code was reading 8. This could result in a corrupted value if the trailing 3 bytes were non-zero, so instead use an appropriately sized and zero-initialized bounce buffer, and read only 5 bytes before casting to u64. | ||||
| CVE-2021-47356 | 2 Linux, Redhat | 6 Linux Kernel, Enterprise Linux, Rhel Aus and 3 more | 2024-08-04 | 7.7 High |
| In the Linux kernel, the following vulnerability has been resolved: mISDN: fix possible use-after-free in HFC_cleanup() This module's remove path calls del_timer(). However, that function does not wait until the timer handler finishes. This means that the timer handler may still be running after the driver's remove function has finished, which would result in a use-after-free. Fix by calling del_timer_sync(), which makes sure the timer handler has finished, and unable to re-schedule itself. | ||||
| CVE-2021-47179 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: NFSv4: Fix a NULL pointer dereference in pnfs_mark_matching_lsegs_return() Commit de144ff4234f changes _pnfs_return_layout() to call pnfs_mark_matching_lsegs_return() passing NULL as the struct pnfs_layout_range argument. Unfortunately, pnfs_mark_matching_lsegs_return() doesn't check if we have a value here before dereferencing it, causing an oops. I'm able to hit this crash consistently when running connectathon basic tests on NFS v4.1/v4.2 against Ontap. | ||||
| CVE-2021-47194 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: cfg80211: call cfg80211_stop_ap when switch from P2P_GO type If the userspace tools switch from NL80211_IFTYPE_P2P_GO to NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), it does not call the cleanup cfg80211_stop_ap(), this leads to the initialization of in-use data. For example, this path re-init the sdata->assigned_chanctx_list while it is still an element of assigned_vifs list, and makes that linked list corrupt. | ||||
| CVE-2021-47193 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: scsi: pm80xx: Fix memory leak during rmmod Driver failed to release all memory allocated. This would lead to memory leak during driver removal. Properly free memory when the module is removed. | ||||
| CVE-2021-47195 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: spi: fix use-after-free of the add_lock mutex Commit 6098475d4cb4 ("spi: Fix deadlock when adding SPI controllers on SPI buses") introduced a per-controller mutex. But mutex_unlock() of said lock is called after the controller is already freed: spi_unregister_controller(ctlr) -> put_device(&ctlr->dev) -> spi_controller_release(dev) -> mutex_unlock(&ctrl->add_lock) Move the put_device() after the mutex_unlock(). | ||||
| CVE-2021-47173 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: misc/uss720: fix memory leak in uss720_probe uss720_probe forgets to decrease the refcount of usbdev in uss720_probe. Fix this by decreasing the refcount of usbdev by usb_put_dev. BUG: memory leak unreferenced object 0xffff888101113800 (size 2048): comm "kworker/0:1", pid 7, jiffies 4294956777 (age 28.870s) hex dump (first 32 bytes): ff ff ff ff 31 00 00 00 00 00 00 00 00 00 00 00 ....1........... 00 00 00 00 00 00 00 00 00 00 00 00 03 00 00 00 ................ backtrace: [<ffffffff82b8e822>] kmalloc include/linux/slab.h:554 [inline] [<ffffffff82b8e822>] kzalloc include/linux/slab.h:684 [inline] [<ffffffff82b8e822>] usb_alloc_dev+0x32/0x450 drivers/usb/core/usb.c:582 [<ffffffff82b98441>] hub_port_connect drivers/usb/core/hub.c:5129 [inline] [<ffffffff82b98441>] hub_port_connect_change drivers/usb/core/hub.c:5363 [inline] [<ffffffff82b98441>] port_event drivers/usb/core/hub.c:5509 [inline] [<ffffffff82b98441>] hub_event+0x1171/0x20c0 drivers/usb/core/hub.c:5591 [<ffffffff81259229>] process_one_work+0x2c9/0x600 kernel/workqueue.c:2275 [<ffffffff81259b19>] worker_thread+0x59/0x5d0 kernel/workqueue.c:2421 [<ffffffff81261228>] kthread+0x178/0x1b0 kernel/kthread.c:292 [<ffffffff8100227f>] ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:294 | ||||
| CVE-2021-47164 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix null deref accessing lag dev It could be the lag dev is null so stop processing the event. In bond_enslave() the active/backup slave being set before setting the upper dev so first event is without an upper dev. After setting the upper dev with bond_master_upper_dev_link() there is a second event and in that event we have an upper dev. | ||||
| CVE-2021-46951 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tpm: efi: Use local variable for calculating final log size When tpm_read_log_efi is called multiple times, which happens when one loads and unloads a TPM2 driver multiple times, then the global variable efi_tpm_final_log_size will at some point become a negative number due to the subtraction of final_events_preboot_size occurring each time. Use a local variable to avoid this integer underflow. The following issue is now resolved: Mar 8 15:35:12 hibinst kernel: Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 Mar 8 15:35:12 hibinst kernel: Workqueue: tpm-vtpm vtpm_proxy_work [tpm_vtpm_proxy] Mar 8 15:35:12 hibinst kernel: RIP: 0010:__memcpy+0x12/0x20 Mar 8 15:35:12 hibinst kernel: Code: 00 b8 01 00 00 00 85 d2 74 0a c7 05 44 7b ef 00 0f 00 00 00 c3 cc cc cc 66 66 90 66 90 48 89 f8 48 89 d1 48 c1 e9 03 83 e2 07 <f3> 48 a5 89 d1 f3 a4 c3 66 0f 1f 44 00 00 48 89 f8 48 89 d1 f3 a4 Mar 8 15:35:12 hibinst kernel: RSP: 0018:ffff9ac4c0fcfde0 EFLAGS: 00010206 Mar 8 15:35:12 hibinst kernel: RAX: ffff88f878cefed5 RBX: ffff88f878ce9000 RCX: 1ffffffffffffe0f Mar 8 15:35:12 hibinst kernel: RDX: 0000000000000003 RSI: ffff9ac4c003bff9 RDI: ffff88f878cf0e4d Mar 8 15:35:12 hibinst kernel: RBP: ffff9ac4c003b000 R08: 0000000000001000 R09: 000000007e9d6073 Mar 8 15:35:12 hibinst kernel: R10: ffff9ac4c003b000 R11: ffff88f879ad3500 R12: 0000000000000ed5 Mar 8 15:35:12 hibinst kernel: R13: ffff88f878ce9760 R14: 0000000000000002 R15: ffff88f77de7f018 Mar 8 15:35:12 hibinst kernel: FS: 0000000000000000(0000) GS:ffff88f87bd00000(0000) knlGS:0000000000000000 Mar 8 15:35:12 hibinst kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Mar 8 15:35:12 hibinst kernel: CR2: ffff9ac4c003c000 CR3: 00000001785a6004 CR4: 0000000000060ee0 Mar 8 15:35:12 hibinst kernel: Call Trace: Mar 8 15:35:12 hibinst kernel: tpm_read_log_efi+0x152/0x1a7 Mar 8 15:35:12 hibinst kernel: tpm_bios_log_setup+0xc8/0x1c0 Mar 8 15:35:12 hibinst kernel: tpm_chip_register+0x8f/0x260 Mar 8 15:35:12 hibinst kernel: vtpm_proxy_work+0x16/0x60 [tpm_vtpm_proxy] Mar 8 15:35:12 hibinst kernel: process_one_work+0x1b4/0x370 Mar 8 15:35:12 hibinst kernel: worker_thread+0x53/0x3e0 Mar 8 15:35:12 hibinst kernel: ? process_one_work+0x370/0x370 | ||||
| CVE-2021-46933 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_fs: Clear ffs_eventfd in ffs_data_clear. ffs_data_clear is indirectly called from both ffs_fs_kill_sb and ffs_ep0_release, so it ends up being called twice when userland closes ep0 and then unmounts f_fs. If userland provided an eventfd along with function's USB descriptors, it ends up calling eventfd_ctx_put as many times, causing a refcount underflow. NULL-ify ffs_eventfd to prevent these extraneous eventfd_ctx_put calls. Also, set epfiles to NULL right after de-allocating it, for readability. For completeness, ffs_data_clear actually ends up being called thrice, the last call being before the whole ffs structure gets freed, so when this specific sequence happens there is a second underflow happening (but not being reported): /sys/kernel/debug/tracing# modprobe usb_f_fs /sys/kernel/debug/tracing# echo ffs_data_clear > set_ftrace_filter /sys/kernel/debug/tracing# echo function > current_tracer /sys/kernel/debug/tracing# echo 1 > tracing_on (setup gadget, run and kill function userland process, teardown gadget) /sys/kernel/debug/tracing# echo 0 > tracing_on /sys/kernel/debug/tracing# cat trace smartcard-openp-436 [000] ..... 1946.208786: ffs_data_clear <-ffs_data_closed smartcard-openp-431 [000] ..... 1946.279147: ffs_data_clear <-ffs_data_closed smartcard-openp-431 [000] .n... 1946.905512: ffs_data_clear <-ffs_data_put Warning output corresponding to above trace: [ 1946.284139] WARNING: CPU: 0 PID: 431 at lib/refcount.c:28 refcount_warn_saturate+0x110/0x15c [ 1946.293094] refcount_t: underflow; use-after-free. [ 1946.298164] Modules linked in: usb_f_ncm(E) u_ether(E) usb_f_fs(E) hci_uart(E) btqca(E) btrtl(E) btbcm(E) btintel(E) bluetooth(E) nls_ascii(E) nls_cp437(E) vfat(E) fat(E) bcm2835_v4l2(CE) bcm2835_mmal_vchiq(CE) videobuf2_vmalloc(E) videobuf2_memops(E) sha512_generic(E) videobuf2_v4l2(E) sha512_arm(E) videobuf2_common(E) videodev(E) cpufreq_dt(E) snd_bcm2835(CE) brcmfmac(E) mc(E) vc4(E) ctr(E) brcmutil(E) snd_soc_core(E) snd_pcm_dmaengine(E) drbg(E) snd_pcm(E) snd_timer(E) snd(E) soundcore(E) drm_kms_helper(E) cec(E) ansi_cprng(E) rc_core(E) syscopyarea(E) raspberrypi_cpufreq(E) sysfillrect(E) sysimgblt(E) cfg80211(E) max17040_battery(OE) raspberrypi_hwmon(E) fb_sys_fops(E) regmap_i2c(E) ecdh_generic(E) rfkill(E) ecc(E) bcm2835_rng(E) rng_core(E) vchiq(CE) leds_gpio(E) libcomposite(E) fuse(E) configfs(E) ip_tables(E) x_tables(E) autofs4(E) ext4(E) crc16(E) mbcache(E) jbd2(E) crc32c_generic(E) sdhci_iproc(E) sdhci_pltfm(E) sdhci(E) [ 1946.399633] CPU: 0 PID: 431 Comm: smartcard-openp Tainted: G C OE 5.15.0-1-rpi #1 Debian 5.15.3-1 [ 1946.417950] Hardware name: BCM2835 [ 1946.425442] Backtrace: [ 1946.432048] [<c08d60a0>] (dump_backtrace) from [<c08d62ec>] (show_stack+0x20/0x24) [ 1946.448226] r7:00000009 r6:0000001c r5:c04a948c r4:c0a64e2c [ 1946.458412] [<c08d62cc>] (show_stack) from [<c08d9ae0>] (dump_stack+0x28/0x30) [ 1946.470380] [<c08d9ab8>] (dump_stack) from [<c0123500>] (__warn+0xe8/0x154) [ 1946.482067] r5:c04a948c r4:c0a71dc8 [ 1946.490184] [<c0123418>] (__warn) from [<c08d6948>] (warn_slowpath_fmt+0xa0/0xe4) [ 1946.506758] r7:00000009 r6:0000001c r5:c0a71dc8 r4:c0a71e04 [ 1946.517070] [<c08d68ac>] (warn_slowpath_fmt) from [<c04a948c>] (refcount_warn_saturate+0x110/0x15c) [ 1946.535309] r8:c0100224 r7:c0dfcb84 r6:ffffffff r5:c3b84c00 r4:c24a17c0 [ 1946.546708] [<c04a937c>] (refcount_warn_saturate) from [<c0380134>] (eventfd_ctx_put+0x48/0x74) [ 1946.564476] [<c03800ec>] (eventfd_ctx_put) from [<bf5464e8>] (ffs_data_clear+0xd0/0x118 [usb_f_fs]) [ 1946.582664] r5:c3b84c00 r4:c2695b00 [ 1946.590668] [<bf546418>] (ffs_data_clear [usb_f_fs]) from [<bf547cc0>] (ffs_data_closed+0x9c/0x150 [usb_f_fs]) [ 1946.609608] r5:bf54d014 r4:c2695b00 [ 1946.617522] [<bf547c24>] (ffs_data_closed [usb_f_fs]) from [<bf547da0>] (ffs_fs_kill_sb+0x2c/0x30 [usb_f_fs]) [ 1946.636217] r7:c0dfcb ---truncated--- | ||||
| CVE-2021-46928 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: parisc: Clear stale IIR value on instruction access rights trap When a trap 7 (Instruction access rights) occurs, this means the CPU couldn't execute an instruction due to missing execute permissions on the memory region. In this case it seems the CPU didn't even fetched the instruction from memory and thus did not store it in the cr19 (IIR) register before calling the trap handler. So, the trap handler will find some random old stale value in cr19. This patch simply overwrites the stale IIR value with a constant magic "bad food" value (0xbaadf00d), in the hope people don't start to try to understand the various random IIR values in trap 7 dumps. | ||||
| CVE-2021-46952 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: NFS: fs_context: validate UDP retrans to prevent shift out-of-bounds Fix shift out-of-bounds in xprt_calc_majortimeo(). This is caused by a garbage timeout (retrans) mount option being passed to nfs mount, in this case from syzkaller. If the protocol is XPRT_TRANSPORT_UDP, then 'retrans' is a shift value for a 64-bit long integer, so 'retrans' cannot be >= 64. If it is >= 64, fail the mount and return an error. | ||||
| CVE-2021-46908 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Use correct permission flag for mixed signed bounds arithmetic We forbid adding unknown scalars with mixed signed bounds due to the spectre v1 masking mitigation. Hence this also needs bypass_spec_v1 flag instead of allow_ptr_leaks. | ||||
| CVE-2021-46939 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tracing: Restructure trace_clock_global() to never block It was reported that a fix to the ring buffer recursion detection would cause a hung machine when performing suspend / resume testing. The following backtrace was extracted from debugging that case: Call Trace: trace_clock_global+0x91/0xa0 __rb_reserve_next+0x237/0x460 ring_buffer_lock_reserve+0x12a/0x3f0 trace_buffer_lock_reserve+0x10/0x50 __trace_graph_return+0x1f/0x80 trace_graph_return+0xb7/0xf0 ? trace_clock_global+0x91/0xa0 ftrace_return_to_handler+0x8b/0xf0 ? pv_hash+0xa0/0xa0 return_to_handler+0x15/0x30 ? ftrace_graph_caller+0xa0/0xa0 ? trace_clock_global+0x91/0xa0 ? __rb_reserve_next+0x237/0x460 ? ring_buffer_lock_reserve+0x12a/0x3f0 ? trace_event_buffer_lock_reserve+0x3c/0x120 ? trace_event_buffer_reserve+0x6b/0xc0 ? trace_event_raw_event_device_pm_callback_start+0x125/0x2d0 ? dpm_run_callback+0x3b/0xc0 ? pm_ops_is_empty+0x50/0x50 ? platform_get_irq_byname_optional+0x90/0x90 ? trace_device_pm_callback_start+0x82/0xd0 ? dpm_run_callback+0x49/0xc0 With the following RIP: RIP: 0010:native_queued_spin_lock_slowpath+0x69/0x200 Since the fix to the recursion detection would allow a single recursion to happen while tracing, this lead to the trace_clock_global() taking a spin lock and then trying to take it again: ring_buffer_lock_reserve() { trace_clock_global() { arch_spin_lock() { queued_spin_lock_slowpath() { /* lock taken */ (something else gets traced by function graph tracer) ring_buffer_lock_reserve() { trace_clock_global() { arch_spin_lock() { queued_spin_lock_slowpath() { /* DEAD LOCK! */ Tracing should *never* block, as it can lead to strange lockups like the above. Restructure the trace_clock_global() code to instead of simply taking a lock to update the recorded "prev_time" simply use it, as two events happening on two different CPUs that calls this at the same time, really doesn't matter which one goes first. Use a trylock to grab the lock for updating the prev_time, and if it fails, simply try again the next time. If it failed to be taken, that means something else is already updating it. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212761 | ||||
| CVE-2021-46945 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ext4: always panic when errors=panic is specified Before commit 014c9caa29d3 ("ext4: make ext4_abort() use __ext4_error()"), the following series of commands would trigger a panic: 1. mount /dev/sda -o ro,errors=panic test 2. mount /dev/sda -o remount,abort test After commit 014c9caa29d3, remounting a file system using the test mount option "abort" will no longer trigger a panic. This commit will restore the behaviour immediately before commit 014c9caa29d3. (However, note that the Linux kernel's behavior has not been consistent; some previous kernel versions, including 5.4 and 4.19 similarly did not panic after using the mount option "abort".) This also makes a change to long-standing behaviour; namely, the following series commands will now cause a panic, when previously it did not: 1. mount /dev/sda -o ro,errors=panic test 2. echo test > /sys/fs/ext4/sda/trigger_fs_error However, this makes ext4's behaviour much more consistent, so this is a good thing. | ||||
| CVE-2021-46941 | 1 Linux | 1 Linux Kernel | 2024-08-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: core: Do core softreset when switch mode According to the programming guide, to switch mode for DRD controller, the driver needs to do the following. To switch from device to host: 1. Reset controller with GCTL.CoreSoftReset 2. Set GCTL.PrtCapDir(host mode) 3. Reset the host with USBCMD.HCRESET 4. Then follow up with the initializing host registers sequence To switch from host to device: 1. Reset controller with GCTL.CoreSoftReset 2. Set GCTL.PrtCapDir(device mode) 3. Reset the device with DCTL.CSftRst 4. Then follow up with the initializing registers sequence Currently we're missing step 1) to do GCTL.CoreSoftReset and step 3) of switching from host to device. John Stult reported a lockup issue seen with HiKey960 platform without these steps[1]. Similar issue is observed with Ferry's testing platform[2]. So, apply the required steps along with some fixes to Yu Chen's and John Stultz's version. The main fixes to their versions are the missing wait for clocks synchronization before clearing GCTL.CoreSoftReset and only apply DCTL.CSftRst when switching from host to device. [1] https://lore.kernel.org/linux-usb/20210108015115.27920-1-john.stultz@linaro.org/ [2] https://lore.kernel.org/linux-usb/0ba7a6ba-e6a7-9cd4-0695-64fc927e01f1@gmail.com/ | ||||