| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix TSO header length truncation
stmmac_tso_xmit() stores the protocol header length returned by
stmmac_tso_header_size() in a u8. stmmac_tso_valid_packet() admits
headers up to 1023 bytes, so a header longer than 255 bytes wraps modulo
256 (486 becomes 230, 256 becomes 0).
A TCP over IPv6 socket carrying a few hundred bytes of sticky
destination/hop-by-hop options makes skb_tcp_all_headers() exceed 255
while staying below the 1023-byte limit, so such an skb reaches
stmmac_tso_xmit().
Widen proto_hdr_len to unsigned int, which is sufficient since the value
is bounded by the hardware limit, and adjust the debug print specifier
accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_qca: Do not write to the serial port after it is closed
hci_uart_close() closes the serdev port if HCI_QUIRK_NON_PERSISTENT_SETUP
is set (for example, for the WCN399x family). A failed hci_dev_open_sync()
following a successful qca_setup() calls hdev->close() but not
hdev->shutdown(), so the port is closed while power->vregs_on is left true.
qca_serdev_remove() then passes its power->vregs_on test and calls
qca_power_off(), which writes to the closed port unconditionally.
Seen on a WCN3988 by unbinding the driver after a controller failure. The
trace below is from a 7.0.0 based kernel, where qca_power_off() was still
named qca_power_shutdown():
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000038
Call trace:
tty_set_termios+0x50/0x238 (P)
ttyport_set_baudrate+0x84/0xc0
serdev_device_set_baudrate+0x24/0x40
qca_power_shutdown+0x158/0x1fc [hci_uart]
qca_serdev_remove+0x54/0x68 [hci_uart]
serdev_drv_remove+0x1c/0x2c
device_remove+0x4c/0x80
device_release_driver_internal+0x1cc/0x224
device_driver_detach+0x18/0x24
unbind_store+0xb4/0xc0
Check HCI_UART_PROTO_READY, which hci_uart_close() clears in the same place
it closes the port, before writing to it. The regulator disable is left
unconditional so the controller is still powered down.
The dangling serport->tty that turns this into a use-after-free is
addressed in a separate patch. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel_pcie: validate TX skb length in send_sync
btintel_pcie_prepare_tx() copies skb->len bytes into a fixed
BTINTEL_PCIE_BUFFER_SIZE (4096) DMA slot via an unchecked memcpy.
Oversized packets are currently rejected only in
btintel_pcie_send_frame(); any future caller of
btintel_pcie_send_sync() would silently overflow the DMA buffer.
Add the bounds check in btintel_pcie_send_sync() itself, right
before skb_push() and the DMA copy. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Fix queuing tx_work after workqueue is drained
hci_send_acl(), hci_send_sco() and hci_send_iso() queue hdev->tx_work
unconditionally. They can run from the L2CAP/SCO/ISO socket send path
while hci_dev_close_sync() is draining hdev->workqueue (HCIDEVDOWN
racing with a socket write). Since that queue_work() is not chained
work from the tx_work worker itself, __queue_work() sees the queue
marked __WQ_DRAINING, warns "cannot queue %ps on wq %s", and drops
the work:
WARNING: CPU: 1 PID: 5985 at kernel/workqueue.c:2352 __queue_work
Call Trace:
queue_work_on
l2cap_chan_send
l2cap_sock_sendmsg
...
hci_dev_close_sync() already sets HCI_CMD_DRAIN_WORKQUEUE before
draining, but only hci_cmd_work() and handle_cmd_cnt_and_timer()
check it before queuing. Route the tx_work producers through the
same guard via a shared hci_sched_tx() helper. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: mmp_pdma: fix wrong sg length in mmp_pdma_prep_slave_sg()
In mmp_pdma_prep_slave_sg(), for_each_sg() iterates the scatterlist
putting each entry into 'sg', but the entry length is read from 'sgl'
(the list head) instead of 'sg' (the current entry):
for_each_sg(sgl, sg, sg_len, i) {
addr = sg_dma_address(sg);
avail = sg_dma_len(sgl); /* should be 'sg' */
Consequently 'avail' is always the length of the first entry. For
multi-sg lists this causes out-of-bounds reads when a later entry is
shorter than the first, and silent data loss when it is longer.
Single-sg or uniformly-sized lists happen to mask the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
seg6: set IPSKB_L3SLAVE from IP6SKB_L3SLAVE on IPIP decapsulation
When an SRv6 packet arrives on an interface enslaved to a VRF,
vrf_ip6_rcv() sets IP6SKB_L3SLAVE in IP6CB, but decap_and_validate()
has never set IPSKB_L3SLAVE in IPCB. The bit stayed clear in the
common case, and with CONFIG_IPV6_MIP6 the leftover frag_max_size of
a reassembled outer packet could even set it, with no VRF involved.
Commit 44930446dde4 ("ipv6: seg6: clear IPv4 control block on IPIP
decapsulation") then made the unreliable bit reliably clear.
The effect of the missing flag is visible with End.DX4 when a
delivery to a local address of the node reaches the socket lookup.
For example, a UDP socket bound to the enslaved ingress interface
does not receive any of the decapsulated packets, while an unbound
socket outside the VRF does.
This contradicts Documentation/networking/vrf.rst: by default the
scope of an unbound UDP or TCP socket is limited to the default VRF.
Set IPSKB_L3SLAVE for IPv4 in decap_and_validate(), which already does
the same for IPv6. The socket lookup then matches the decapsulated
packet like any other packet received on that enslaved interface. Such
a packet matches an unbound UDP or TCP socket only when
udp_l3mdev_accept or tcp_l3mdev_accept is set. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: cleanup arsta in ath11k_mac_peer_cleanup_all()
When mac80211 removes a sta, it calls .sta_state() which in turn calls
ath11k_mac_station_remove(). In that function we clean up both peers &
arsta related resources.
But when the firmware crashes, ath11k calls ieee80211_restart_hw(), which
assumes that all driver related resources are cleaned up beforehand. This
cleanup is supposedly done by ath11k_mac_peer_cleanup_all() but does not
in fact free arsta->rx_stats / tx_stats.
Extract the arsta cleanup from ath11k_mac_station_remove() into a
new ath11k_mac_station_cleanup() and call it from both there and
ath11k_mac_peer_cleanup_all().
This should handle kmemleaks reports like:
unreferenced object 0xffffff801ae66400 (size 1024):
comm "hostapd", pid 1306, jiffies 4295011565
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc d61c08ec):
kmemleak_alloc+0x3c/0x50
__kmalloc_cache_noprof+0x2b0/0x3e0
ath11k_mac_op_sta_state+0x1dc/0xb10
drv_sta_state+0xac/0x6f8
sta_info_insert_rcu+0x314/0x5e0
sta_info_insert+0x14/0x38
ieee80211_add_station+0x10c/0x1a0
nl80211_new_station+0x3e8/0x680
genl_family_rcv_msg_doit+0xc0/0x120
genl_rcv_msg+0x1b4/0x258
netlink_rcv_skb+0x4c/0x108
genl_rcv+0x38/0x60
netlink_unicast+0x190/0x278
netlink_sendmsg+0x15c/0x370
____sys_sendmsg+0x120/0x290
___sys_sendmsg+0x70/0xa0
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.9.0.1-01977-QCAHKSWPL_SILICONZ-1 |
| A heap buffer overflow vulnerability in the FileMaker Server database engine block parsing routine allowed a maliciously crafted .fmp12 database file to cause memory corruption, potentially leading to arbitrary code execution. This vulnerability is addressed in FileMaker Server version 26.0.3. |
| Improper neutralization of input during web page generation ('cross-site scripting') vulnerability in Akıllı Ticaret Software Technologies Ltd. Co. E-Commerce Pack allows Reflected XSS.
This issue affects E-Commerce Pack: through 2026-10-06. NOTE: The vendor was contacted early about this disclosure but did not respond in any way. |
| In the Linux kernel, the following vulnerability has been resolved:
mips: select CONFIG_WEAK_REORDERING_BEYOND_LLSC from CONFIG_EYEQ
On I6500 CPU cores, lld and scd give no ordering guarantees (same as all
other instructions). To respect the assumption that arch_cmpxchg() is
fully ordered, we must inject sync instructions above and below our
lld/scd loops using the already in place WEAK_REORDERING_BEYOND_LLSC
infrastructure.
Otherwise, bad things can happen:
[ 34.054496] CPU 3 Unable to handle kernel paging request at virtual address 0000000000000000, epc == a80000080838e01c, ra == a80000080838dfc4
[ 34.054559] Oops[#1]:
[ 34.069561] CPU: 3 UID: 0 PID: 170 Comm: pipe_race Not tainted 7.2.0-rc6-01553-gb73c35220968-dirty #103 VOLUNTARY
[ 34.079932] Hardware name: Mobile EyeQ5 MP5 Evaluation board
[ 34.085592] $ 0 : 0000000000000000 0000000000000001 0000000000000000 0000000000000000
[ 34.093616] $ 4 : a800000808ee2618 000000000b7a879d 0000000000001000 0000000000000000
[ 34.101638] $ 8 : 0000000000e3f2c9 0000000000000000 a800000808a2a9f8 0000000000000000
[ 34.109660] $12 : a8000008139ffcd8 ffffffff84080018 a80000080837fae0 7878787878787878
[ 34.117682] $16 : a800000807e82940 0000000000001000 0000000000000000 0000000000000000
[ 34.125704] $20 : a800000802920e00 a8000008139ffdf8 a800000802649400 0000000000e3f2c9
[ 34.133726] $24 : 0000000000000006 00000001200406e0
[ 34.141783] $28 : a8000008139fc000 a8000008139ffd10 0000000000e3f2c8 a80000080838dfc4
[ 34.149837] epc : a80000080838e01c anon_pipe_read+0xd4/0x428
[ 34.155697] ra : a80000080838dfc4 anon_pipe_read+0x7c/0x428
[ 34.161549] Status: 140000e3 KX SX UX KERNEL EXL IE
[ 34.166551] Cause : 40800408 (ExcCode 02)
[ 34.170574] BadVA : 0000000000000000
[ 34.174161] PrId : 0001b028 (MIPS I6500)
[ 34.178183] Process pipe_race (pid: 170, threadinfo=000000005ca35720, task=00000000e1013890, tls=000000014ebbb780)
[ 34.188568] Stack : a800000802649400 0000000000000000 0000000000000000 a8000008139ffdd0
[ 34.196623] 0000000000000fba a800000808ee0000 0000000000000001 a8000008130c3e80
[ 34.204676] a8000008080d1280 a8000008139ffd58 a8000008139ffd58 1dbd2b22ea1dd500
[ 34.212729] a800000802649400 a800000808ee0000 ffffffffffffffea 0000000000000001
[ 34.220783] 0000000000001000 0000000000000000 00000001200ae518 ffffffffffffffff
[ 34.228836] 000000fffbe0e530 a80000080837edf4 000000fffbe0e530 0000000000000000
[ 34.236890] 0000000000000000 0000000000000000 000000014ebb55a0 0000000000001000
[ 34.244943] 0000000000000001 a800000802649400 0000000000000000 0000000000000000
[ 34.252996] 0000000000000000 0000400400000000 0000000000000000 1dbd2b22ea1dd500
[ 34.261049] 00000000140000e3 a800000802649400 a800000802649400 a800000808ee0000
[ 34.269103] ...
[ 34.271568] Call Trace:
[ 34.274026] [<a80000080838e01c>] anon_pipe_read+0xd4/0x428
[ 34.279533] [<a80000080837edf4>] vfs_read+0x25c/0x318
[ 34.284607] [<a80000080837faac>] ksys_read+0x104/0x138
[ 34.289763] [<a80000080802b9cc>] syscall_common+0x44/0x68
[ 34.295187]
[ 34.296689] Code: f84000cf 02209825 de020010 <dc420000> d8400004 02002825 0040f809 02802025 f84000c3
[ 34.306504]
[ 34.308099] ---[ end trace 0000000000000000 ]---
My initial reproducer was the xdp-tools test suite. A standalone
reproducer would be an lld/scd loop that, when the read is reordered by
the CPU, triggers a fault. We can achieve this from userspace by
stressing an anonymous pipe, which uses a mutex. Program used:
// SPDX-License-Identifier: GPL-2.0
// pipe_race.c - reproducer for MIPS LL/SC reordering vs fs/pipe.c
//
// Two userspace processes on an anonymous pipe:
// parent = writer: tight write() loop
// child = reader: tight read() loop
#define _GNU_SOURCE
#include <assert.h>
#include <errno.h>
#include <sched.h>
#include <signal.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <sys/types.h>
#include
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: save input state data before secpath resets
xfrm_input() stores the current xfrm_state in the skb secpath while it
continues receive-side processing. Some input paths can reset that secpath
before xfrm_input() has finished dereferencing the state.
Receive callback users such as VTI and XFRM interfaces can reset the
secpath. The VTI receive path does so before checking whether the packet
crosses network namespaces, while the XFRM interface path does so only for
cross-network-namespace packets. The XFRM_MAX_DEPTH error path can also
reset the secpath before the final drop callback reports the current
state's protocol.
If secpath_reset() drops the last state reference while the state is
concurrently deleted, xfrm_input() can still dereference the freed state
when selecting transport_finish() or reporting the drop callback protocol.
Save the state protocol on the stack while the state is still valid,
and use the already saved address family for transport_finish(). A larval
XFRM_STATE_ACQ state has no type, so retain nexthdr as its protocol. This
preserves the existing drop-path fallback while avoiding the post-reset
state dereferences without adding an extra state reference to every
received packet. |
| In the Linux kernel, the following vulnerability has been resolved:
net: wwan: mhi_wwan_mbim: check skb_copy_bits() return value
mhi_mbim_rx() ignores the return value of skb_copy_bits() when it
copies each datagram out of the NTB. The datagram offset and length
come from the DPE, which is only checked to lie within the NTB
itself, so a modem can point a datagram outside the received skb.
The copy then fails and the freshly allocated skbn is passed to
netif_rx() with its uninitialized contents still in place, leaking
kernel heap memory into the network stack.
Free the skb and account an error when the copy fails.
Verified in a QEMU guest with a fault injector pointing a DPE
outside the received NTB: the copy fails, and the unpatched driver
hands the uninitialized skbn to the network stack (observed as
"unknown protocol" on bytes that were never written). With this
check the failed datagram is dropped and counted as an rx error.
Changes in v2: factor the free-and-count sequence out into
mhi_mbim_rx_drop(), shared with the unknown-protocol path, as
suggested by Loic Poulain. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: xfrm: use full sockets in local error paths
xfrm6_local_rxpmtu() and xfrm6_local_error() dereference skb->sk as if it
always pointed at a full IPv6 socket.
That is not guaranteed. TCP SYN-ACK skbs can be owned by a
TCP_NEW_SYN_RECV request_sock while the output path itself is driven by the
full listener. If rerouting selects an IPv6 XFRM tunnel route with a lower
MTU, the local PMTU/error handling path can reach these callbacks with that
mini-socket still attached to the skb.
The callbacks then miscast the request socket as a full inet/IPv6 socket and
can read beyond the request_sock allocation when they access inet_sock or
ipv6_pinfo state.
Resolve the owner with skb_to_full_sk() in both callbacks and bail out when
no full socket is attached. This matches the surrounding XFRM IPv6 PMTU/error
logic, which already reasons about full sockets with skb_to_full_sk(). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: clear free space tree creation state on rebuild failure
btrfs_rebuild_free_space_tree() sets BTRFS_FS_CREATING_FREE_SPACE_TREE
before rebuilding the free space tree. Several error paths return
without clearing this flag.
The transaction restart failure path can leave the flag set on a live
filesystem, causing delayed reference processing to be skipped. Clear it
on all free space tree rebuild failure paths. Keep
BTRFS_FS_FREE_SPACE_TREE_UNTRUSTED set, since a failed rebuild leaves
the free space tree untrusted. Callers must fall back to extent-tree
caching. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: 6fire: fix OOB write from device-reported iso length
usb6fire_pcm_in_urb_handler() sizes each outgoing isochronous packet as
(actual_length - 4) / (in_n_analog << 2) * (out_n_analog << 2) + 4, where
actual_length is the unsigned length the device reported for the matching
IN packet. A packet completed with status 0 and actual_length < 4 wraps
the subtraction to 0x7fffffec; a zero-length isochronous packet is legal
on the bus, and the preceding loop rejects only non-zero status. The sum
reaches memset() on out_urb->buffer, a 4832-byte object from
kcalloc(PCM_MAX_PACKET_SIZE, PCM_N_PACKETS_PER_URB).
Even without the wrap the result is out of bounds: at 88.2/96 kHz the
4-in/6-out scaling turns a full 420-byte IN packet into 628, so eight
packets span 5024 bytes of that buffer. usb_submit_urb() rejects an
over-long descriptor only after the memset() and the
usb6fire_pcm_playback() copy of user PCM data have run.
Guard the subtraction as the sibling usb6fire_pcm_capture() already does,
and limit the frame count to what fits in rt->out_packet_size, the OUT
endpoint's wMaxPacketSize. This bounds total_length by the buffer size
while keeping each packet length aligned to a whole output frame.
BUG: KASAN: out-of-bounds in usb6fire_pcm_in_urb_handler (sound/usb/6fire/pcm.c:338)
Write of size 18446744073709551456 at addr ffff88802a3d0000 by task vhci_rx/5018
Call Trace:
dump_stack_lvl (lib/dump_stack.c:94 lib/dump_stack.c:120)
print_report (mm/kasan/report.c:378 mm/kasan/report.c:482)
kasan_report (mm/kasan/report.c:595)
kasan_check_range (mm/kasan/generic.c:186 mm/kasan/generic.c:200)
__asan_memset (mm/kasan/shadow.c:84)
usb6fire_pcm_in_urb_handler (sound/usb/6fire/pcm.c:338)
__usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1657)
usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1741)
vhci_rx_loop (drivers/usb/usbip/vhci_rx.c:107 drivers/usb/usbip/vhci_rx.c:242)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245)
Allocated by task 10:
__kmalloc_cache_noprof (mm/slub.c:5563)
usb6fire_pcm_init (sound/usb/6fire/pcm.c:560 sound/usb/6fire/pcm.c:595)
usb6fire_chip_probe (sound/usb/6fire/chip.c:133)
usb_probe_interface (drivers/usb/core/driver.c:399)
The buggy address belongs to the object at ffff88802a3d0000
which belongs to the cache kmalloc-8k of size 8192
The buggy address is located 0 bytes inside of
4832-byte region [ffff88802a3d0000, ffff88802a3d12e0)
Kernel panic - not syncing: Fatal exception in interrupt |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_nat: unregister and release hooks on error
If nf_hook_entries_insert_raw() fails, the NAT hooks get never released,
resulting in a memleak.
Postpone setting nat_proto_net->nat_hook_ops when the hooks are
registered to simplify the error path to decide whether the nat hooks
need unwinding. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: Bound fragmented header copies by the remaining length
siw_get_hdr() can receive an extended DDP/RDMAP header across more than
one TCP callback. The first callback may receive most of the header,
while the next one still limits the copy to hdrlen - MIN_DDP_HDR instead
of the number of missing bytes. This makes the destination move past the
end of the header and overwrite the receive state, including
fpdu_part_rcvd. A later callback can then use a negative fpdu_part_rcvd
value as a copy offset, which creates an OOB write.
Use the number of header bytes already received when calculating the
next copy length. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: get the wiphy out of a dying network namespace
When a network namespace is destroyed, cfg80211_pernet_exit() moves any
wiphy back to the initial namespace, and just warns if that fails. But
moving an interface can fail (due to allocation failures), and then the
wiphy is left behind with a garbage netns pointer:
Kernel mode fault at addr 0x30
genlmsg_multicast_netns.constprop.0+0x46/0xcf [cfg80211]
nl80211_notify_wiphy+0xcd/0xe8 [cfg80211]
wiphy_unregister+0x169/0x3fc [cfg80211]
Note that commit debac3a20dec ("net: Remove conflicting altnames for
dying netns in __dev_change_net_namespace().") fixed another path
that could reach it without allocation failures.
Remove interfaces that cannot be moved instead of failing the switch,
so that the wiphy always ends up in the initial namespace. In this
case the netdev core will unregister the interfaces anyway. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: unlist vifs when their netdev is unregistered
mac80211 only removes vifs from the local->interfaces list when
an interface is removed via ieee80211_if_remove(), before it
unregisters the netdev. However, it's possible for a netdev to
be unregistered without going through that: When the netns that
holds the wiphy is destroyed, the wiphy is supposed to move to
the init_ns, but that can run into allocation failures.
Then, mac80211 has an interface listed that doesn't exist, and
will eventually hit
BUG: failure at net/wireless/core.h:141/wiphy_to_rdev()!
...
_cfg80211_unregister_wdev+0x24/0x36a [cfg80211]
cfg80211_unregister_wdev+0x15/0x1d [cfg80211]
ieee80211_remove_interfaces+0x1ff/0x257 [mac80211]
ieee80211_unregister_hw+0x73/0x1d1 [mac80211]
mac80211_hwsim_del_radio+0x114/0x166 [mac80211_hwsim]
Remove the interface from the list in ->ndo_uninit if it's still
around to avoid this. |
| A vulnerability was found in Kusalkasilva Learning-Management-System up to ffeb873f8803f1e9664384ff75000c7da45466d2. The affected element is the function mysql_query of the file admin/login.php of the component Administrator Login Endpoint. The manipulation of the argument username/password results in sql injection. The attack can be launched remotely. The exploit has been made public and could be used. This product does not use versioning. This is why information about affected and unaffected releases are unavailable. The project was informed of the problem early through an issue report but has not responded yet. |
