| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: Fix NULL pointer dereference in core_scsi3_decode_spec_i_port()
The function core_scsi3_decode_spec_i_port(), in its error code path,
unconditionally calls core_scsi3_lunacl_undepend_item() passing the
dest_se_deve pointer, which may be NULL.
This can lead to a NULL pointer dereference if dest_se_deve remains
unset.
SPC-3 PR SPEC_I_PT: Unable to locate dest_tpg
Unable to handle kernel paging request at virtual address dfff800000000012
Call trace:
core_scsi3_lunacl_undepend_item+0x2c/0xf0 [target_core_mod] (P)
core_scsi3_decode_spec_i_port+0x120c/0x1c30 [target_core_mod]
core_scsi3_emulate_pro_register+0x6b8/0xcd8 [target_core_mod]
target_scsi3_emulate_pr_out+0x56c/0x840 [target_core_mod]
Fix this by adding a NULL check before calling
core_scsi3_lunacl_undepend_item() |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-qpic-snand: reallocate BAM transactions
Using the mtd_nandbiterrs module for testing the driver occasionally
results in weird things like below.
1. swiotlb mapping fails with the following message:
[ 85.926216] qcom_snand 79b0000.spi: swiotlb buffer is full (sz: 4294967294 bytes), total 512 (slots), used 0 (slots)
[ 85.932937] qcom_snand 79b0000.spi: failure in mapping desc
[ 87.999314] qcom_snand 79b0000.spi: failure to write raw page
[ 87.999352] mtd_nandbiterrs: error: write_oob failed (-110)
Rebooting the board after this causes a panic due to a NULL pointer
dereference.
2. If the swiotlb mapping does not fail, rebooting the board may result
in a different panic due to a bad spinlock magic:
[ 256.104459] BUG: spinlock bad magic on CPU#3, procd/2241
[ 256.104488] Unable to handle kernel paging request at virtual address ffffffff0000049b
...
Investigating the issue revealed that these symptoms are results of
memory corruption which is caused by out of bounds access within the
driver.
The driver uses a dynamically allocated structure for BAM transactions,
which structure must have enough space for all possible variations of
different flash operations initiated by the driver. The required space
heavily depends on the actual number of 'codewords' which is calculated
from the pagesize of the actual NAND chip.
Although the qcom_nandc_alloc() function allocates memory for the BAM
transactions during probe, but since the actual number of 'codewords'
is not yet know the allocation is done for one 'codeword' only.
Because of this, whenever the driver does a flash operation, and the
number of the required transactions exceeds the size of the allocated
arrays the driver accesses memory out of the allocated range.
To avoid this, change the code to free the initially allocated BAM
transactions memory, and allocate a new one once the actual number of
'codewords' required for a given NAND chip is known. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: gpio: Fix the out-of-bounds access to drvdata::gpiods
drvdata::gpiods is supposed to hold an array of 'gpio_desc' pointers. But
the memory is allocated for only one pointer. This will lead to
out-of-bounds access later in the code if 'config::ngpios' is > 1. So
fix the code to allocate enough memory to hold 'config::ngpios' of GPIO
descriptors.
While at it, also move the check for memory allocation failure to be below
the allocation to make it more readable. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4/pNFS: Fix a race to wake on NFS_LAYOUT_DRAIN
We found a few different systems hung up in writeback waiting on the same
page lock, and one task waiting on the NFS_LAYOUT_DRAIN bit in
pnfs_update_layout(), however the pnfs_layout_hdr's plh_outstanding count
was zero.
It seems most likely that this is another race between the waiter and waker
similar to commit ed0172af5d6f ("SUNRPC: Fix a race to wake a sync task").
Fix it up by applying the advised barrier. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: Refuse to evaluate a method if arguments are missing
As reported in [1], a platform firmware update that increased the number
of method parameters and forgot to update a least one of its callers,
caused ACPICA to crash due to use-after-free.
Since this a result of a clear AML issue that arguably cannot be fixed
up by the interpreter (it cannot produce missing data out of thin air),
address it by making ACPICA refuse to evaluate a method if the caller
attempts to pass fewer arguments than expected to it. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix iteration of extrefs during log replay
At __inode_add_ref() when processing extrefs, if we jump into the next
label we have an undefined value of victim_name.len, since we haven't
initialized it before we did the goto. This results in an invalid memory
access in the next iteration of the loop since victim_name.len was not
initialized to the length of the name of the current extref.
Fix this by initializing victim_name.len with the current extref's name
length. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix warning when reconnecting channel
When reconnecting a channel in smb2_reconnect_server(), a dummy tcon
is passed down to smb2_reconnect() with ->query_interface
uninitialized, so we can't call queue_delayed_work() on it.
Fix the following warning by ensuring that we're queueing the delayed
worker from correct tcon.
WARNING: CPU: 4 PID: 1126 at kernel/workqueue.c:2498 __queue_delayed_work+0x1d2/0x200
Modules linked in: cifs cifs_arc4 nls_ucs2_utils cifs_md4 [last unloaded: cifs]
CPU: 4 UID: 0 PID: 1126 Comm: kworker/4:0 Not tainted 6.16.0-rc3 #5 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-4.fc42 04/01/2014
Workqueue: cifsiod smb2_reconnect_server [cifs]
RIP: 0010:__queue_delayed_work+0x1d2/0x200
Code: 41 5e 41 5f e9 7f ee ff ff 90 0f 0b 90 e9 5d ff ff ff bf 02 00
00 00 e8 6c f3 07 00 89 c3 eb bd 90 0f 0b 90 e9 57 f> 0b 90 e9 65 fe
ff ff 90 0f 0b 90 e9 72 fe ff ff 90 0f 0b 90 e9
RSP: 0018:ffffc900014afad8 EFLAGS: 00010003
RAX: 0000000000000000 RBX: ffff888124d99988 RCX: ffffffff81399cc1
RDX: dffffc0000000000 RSI: ffff888114326e00 RDI: ffff888124d999f0
RBP: 000000000000ea60 R08: 0000000000000001 R09: ffffed10249b3331
R10: ffff888124d9998f R11: 0000000000000004 R12: 0000000000000040
R13: ffff888114326e00 R14: ffff888124d999d8 R15: ffff888114939020
FS: 0000000000000000(0000) GS:ffff88829f7fe000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffe7a2b4038 CR3: 0000000120a6f000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
<TASK>
queue_delayed_work_on+0xb4/0xc0
smb2_reconnect+0xb22/0xf50 [cifs]
smb2_reconnect_server+0x413/0xd40 [cifs]
? __pfx_smb2_reconnect_server+0x10/0x10 [cifs]
? local_clock_noinstr+0xd/0xd0
? local_clock+0x15/0x30
? lock_release+0x29b/0x390
process_one_work+0x4c5/0xa10
? __pfx_process_one_work+0x10/0x10
? __list_add_valid_or_report+0x37/0x120
worker_thread+0x2f1/0x5a0
? __kthread_parkme+0xde/0x100
? __pfx_worker_thread+0x10/0x10
kthread+0x1fe/0x380
? kthread+0x10f/0x380
? __pfx_kthread+0x10/0x10
? local_clock_noinstr+0xd/0xd0
? ret_from_fork+0x1b/0x1f0
? local_clock+0x15/0x30
? lock_release+0x29b/0x390
? rcu_is_watching+0x20/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork+0x15b/0x1f0
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
irq event stamp: 1116206
hardirqs last enabled at (1116205): [<ffffffff8143af42>] __up_console_sem+0x52/0x60
hardirqs last disabled at (1116206): [<ffffffff81399f0e>] queue_delayed_work_on+0x6e/0xc0
softirqs last enabled at (1116138): [<ffffffffc04562fd>] __smb_send_rqst+0x42d/0x950 [cifs]
softirqs last disabled at (1116136): [<ffffffff823d35e1>] release_sock+0x21/0xf0 |
| In the Linux kernel, the following vulnerability has been resolved:
rose: fix dangling neighbour pointers in rose_rt_device_down()
There are two bugs in rose_rt_device_down() that can cause
use-after-free:
1. The loop bound `t->count` is modified within the loop, which can
cause the loop to terminate early and miss some entries.
2. When removing an entry from the neighbour array, the subsequent entries
are moved up to fill the gap, but the loop index `i` is still
incremented, causing the next entry to be skipped.
For example, if a node has three neighbours (A, A, B) with count=3 and A
is being removed, the second A is not checked.
i=0: (A, A, B) -> (A, B) with count=2
^ checked
i=1: (A, B) -> (A, B) with count=2
^ checked (B, not A!)
i=2: (doesn't occur because i < count is false)
This leaves the second A in the array with count=2, but the rose_neigh
structure has been freed. Code that accesses these entries assumes that
the first `count` entries are valid pointers, causing a use-after-free
when it accesses the dangling pointer.
Fix both issues by iterating over the array in reverse order with a fixed
loop bound. This ensures that all entries are examined and that the removal
of an entry doesn't affect subsequent iterations. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio-net: ensure the received length does not exceed allocated size
In xdp_linearize_page, when reading the following buffers from the ring,
we forget to check the received length with the true allocate size. This
can lead to an out-of-bound read. This commit adds that missing check. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix unsafe xarray access in implicit ODP handling
__xa_store() and __xa_erase() were used without holding the proper lock,
which led to a lockdep warning due to unsafe RCU usage. This patch
replaces them with xa_store() and xa_erase(), which perform the necessary
locking internally.
=============================
WARNING: suspicious RCPU usage
6.14.0-rc7_for_upstream_debug_2025_03_18_15_01 #1 Not tainted
-----------------------------
./include/linux/xarray.h:1211 suspicious rcu_dereference_protected() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
3 locks held by kworker/u136:0/219:
at: process_one_work+0xbe4/0x15f0
process_one_work+0x75c/0x15f0
pagefault_mr+0x9a5/0x1390 [mlx5_ib]
stack backtrace:
CPU: 14 UID: 0 PID: 219 Comm: kworker/u136:0 Not tainted
6.14.0-rc7_for_upstream_debug_2025_03_18_15_01 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_ib_page_fault mlx5_ib_eqe_pf_action [mlx5_ib]
Call Trace:
dump_stack_lvl+0xa8/0xc0
lockdep_rcu_suspicious+0x1e6/0x260
xas_create+0xb8a/0xee0
xas_store+0x73/0x14c0
__xa_store+0x13c/0x220
? xa_store_range+0x390/0x390
? spin_bug+0x1d0/0x1d0
pagefault_mr+0xcb5/0x1390 [mlx5_ib]
? _raw_spin_unlock+0x1f/0x30
mlx5_ib_eqe_pf_action+0x3be/0x2620 [mlx5_ib]
? lockdep_hardirqs_on_prepare+0x400/0x400
? mlx5_ib_invalidate_range+0xcb0/0xcb0 [mlx5_ib]
process_one_work+0x7db/0x15f0
? pwq_dec_nr_in_flight+0xda0/0xda0
? assign_work+0x168/0x240
worker_thread+0x57d/0xcd0
? rescuer_thread+0xc40/0xc40
kthread+0x3b3/0x800
? kthread_is_per_cpu+0xb0/0xb0
? lock_downgrade+0x680/0x680
? do_raw_spin_lock+0x12d/0x270
? spin_bug+0x1d0/0x1d0
? finish_task_switch.isra.0+0x284/0x9e0
? lockdep_hardirqs_on_prepare+0x284/0x400
? kthread_is_per_cpu+0xb0/0xb0
ret_from_fork+0x2d/0x70
? kthread_is_per_cpu+0xb0/0xb0
ret_from_fork_asm+0x11/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: KVM: Avoid overflow with array index
The variable index is modified and reused as array index when modify
register EIOINTC_ENABLE. There will be array index overflow problem. |
| In the Linux kernel, the following vulnerability has been resolved:
posix-cpu-timers: fix race between handle_posix_cpu_timers() and posix_cpu_timer_del()
If an exiting non-autoreaping task has already passed exit_notify() and
calls handle_posix_cpu_timers() from IRQ, it can be reaped by its parent
or debugger right after unlock_task_sighand().
If a concurrent posix_cpu_timer_del() runs at that moment, it won't be
able to detect timer->it.cpu.firing != 0: cpu_timer_task_rcu() and/or
lock_task_sighand() will fail.
Add the tsk->exit_state check into run_posix_cpu_timers() to fix this.
This fix is not needed if CONFIG_POSIX_CPU_TIMERS_TASK_WORK=y, because
exit_task_work() is called before exit_notify(). But the check still
makes sense, task_work_add(&tsk->posix_cputimers_work.work) will fail
anyway in this case. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: drop fragments with multicast or broadcast RA
IEEE 802.11 fragmentation can only be applied to unicast frames.
Therefore, drop fragments with multicast or broadcast RA. This patch
addresses vulnerabilities such as CVE-2020-26145. |
| In the Linux kernel, the following vulnerability has been resolved:
software node: Correct a OOB check in software_node_get_reference_args()
software_node_get_reference_args() wants to get @index-th element, so
the property value requires at least '(index + 1) * sizeof(*ref)' bytes
but that can not be guaranteed by current OOB check, and may cause OOB
for malformed property.
Fix by using as OOB check '((index + 1) * sizeof(*ref) > prop->length)'. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/bpf: fix JIT code size calculation of bpf trampoline
arch_bpf_trampoline_size() provides JIT size of the BPF trampoline
before the buffer for JIT'ing it is allocated. The total number of
instructions emitted for BPF trampoline JIT code depends on where
the final image is located. So, the size arrived at with the dummy
pass in arch_bpf_trampoline_size() can vary from the actual size
needed in arch_prepare_bpf_trampoline(). When the instructions
accounted in arch_bpf_trampoline_size() is less than the number of
instructions emitted during the actual JIT compile of the trampoline,
the below warning is produced:
WARNING: CPU: 8 PID: 204190 at arch/powerpc/net/bpf_jit_comp.c:981 __arch_prepare_bpf_trampoline.isra.0+0xd2c/0xdcc
which is:
/* Make sure the trampoline generation logic doesn't overflow */
if (image && WARN_ON_ONCE(&image[ctx->idx] >
(u32 *)rw_image_end - BPF_INSN_SAFETY)) {
So, during the dummy pass, instead of providing some arbitrary image
location, account for maximum possible instructions if and when there
is a dependency with image location for JIT'ing. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to bail out in get_new_segment()
------------[ cut here ]------------
WARNING: CPU: 3 PID: 579 at fs/f2fs/segment.c:2832 new_curseg+0x5e8/0x6dc
pc : new_curseg+0x5e8/0x6dc
Call trace:
new_curseg+0x5e8/0x6dc
f2fs_allocate_data_block+0xa54/0xe28
do_write_page+0x6c/0x194
f2fs_do_write_node_page+0x38/0x78
__write_node_page+0x248/0x6d4
f2fs_sync_node_pages+0x524/0x72c
f2fs_write_checkpoint+0x4bc/0x9b0
__checkpoint_and_complete_reqs+0x80/0x244
issue_checkpoint_thread+0x8c/0xec
kthread+0x114/0x1bc
ret_from_fork+0x10/0x20
get_new_segment() detects inconsistent status in between free_segmap
and free_secmap, let's record such error into super block, and bail
out get_new_segment() instead of continue using the segment. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: cortina: Use TOE/TSO on all TCP
It is desireable to push the hardware accelerator to also
process non-segmented TCP frames: we pass the skb->len
to the "TOE/TSO" offloader and it will handle them.
Without this quirk the driver becomes unstable and lock
up and and crash.
I do not know exactly why, but it is probably due to the
TOE (TCP offload engine) feature that is coupled with the
segmentation feature - it is not possible to turn one
part off and not the other, either both TOE and TSO are
active, or neither of them.
Not having the TOE part active seems detrimental, as if
that hardware feature is not really supposed to be turned
off.
The datasheet says:
"Based on packet parsing and TCP connection/NAT table
lookup results, the NetEngine puts the packets
belonging to the same TCP connection to the same queue
for the software to process. The NetEngine puts
incoming packets to the buffer or series of buffers
for a jumbo packet. With this hardware acceleration,
IP/TCP header parsing, checksum validation and
connection lookup are offloaded from the software
processing."
After numerous tests with the hardware locking up after
something between minutes and hours depending on load
using iperf3 I have concluded this is necessary to stabilize
the hardware. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: Log an error when close_all_cached_dirs fails
Under low-memory conditions, close_all_cached_dirs() can't move the
dentries to a separate list to dput() them once the locks are dropped.
This will result in a "Dentry still in use" error, so add an error
message that makes it clear this is what happened:
[ 495.281119] CIFS: VFS: \\otters.example.com\share Out of memory while dropping dentries
[ 495.281595] ------------[ cut here ]------------
[ 495.281887] BUG: Dentry ffff888115531138{i=78,n=/} still in use (2) [unmount of cifs cifs]
[ 495.282391] WARNING: CPU: 1 PID: 2329 at fs/dcache.c:1536 umount_check+0xc8/0xf0
Also, bail out of looping through all tcons as soon as a single
allocation fails, since we're already in trouble, and kmalloc() attempts
for subseqeuent tcons are likely to fail just like the first one did. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio-pci: Fix result size returned for the admin command completion
The result size returned by virtio_pci_admin_dev_parts_get() is 8 bytes
larger than the actual result data size. This occurs because the
result_sg_size field of the command is filled with the result length
from virtqueue_get_buf(), which includes both the data size and an
additional 8 bytes of status.
This oversized result size causes two issues:
1. The state transferred to the destination includes 8 bytes of extra
data at the end.
2. The allocated buffer in the kernel may be smaller than the returned
size, leading to failures when reading beyond the allocated size.
The commit fixes this by subtracting the status size from the result of
virtqueue_get_buf().
This fix has been tested through live migrations with virtio-net,
virtio-net-transitional, and virtio-blk devices. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/fhandle.c: fix a race in call of has_locked_children()
may_decode_fh() is calling has_locked_children() while holding no locks.
That's an oopsable race...
The rest of the callers are safe since they are holding namespace_sem and
are guaranteed a positive refcount on the mount in question.
Rename the current has_locked_children() to __has_locked_children(), make
it static and switch the fs/namespace.c users to it.
Make has_locked_children() a wrapper for __has_locked_children(), calling
the latter under read_seqlock_excl(&mount_lock). |
